lkml.org 
[lkml]   [2016]   [Apr]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 1/2] dt/bindings/usb: Add bindings for PIC32 MUSB driver.
Date
Document devicetree binding for the USB controller
and USB Phy found on Microchip PIC32 class devices.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>

---

.../bindings/usb/microchip,pic32-musb.txt | 67 ++++++++++++++++++++++
1 file changed, 67 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt

diff --git a/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt b/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt
new file mode 100644
index 0000000..e1cec9d
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/microchip,pic32-musb.txt
@@ -0,0 +1,67 @@
+Microchip PIC32 MUSB DRC/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible : should be "microchip,pic32mzda-usb".
+ - reg : offset and length of "MUSB Core Registers" and
+ "USB Clock & Reset Registers".
+ - reg-names : should be "mc", and "usbcr" in order
+ - clocks : clock specifier for the musb controller clock
+ - clock-names : should be "usb_clk"
+ - interrupts : interrupt number for MUSB Core General interrupt
+ and DMA interrupt
+ - interrupt-names : must be "mc" and "dma" in order.
+ - phys : phy specifier for the otg phy.
+ - dr_mode : should be one of "host", "peripheral" or "otg".
+ - mentor,multipoint: Should be "1" indicating the musb controller supports
+ multipoint. This is MUSB configuration-specific setting.
+ - mentor,num-eps : Specifies the number of endpoints. This is also a
+ MUSB configuration-specific setting. Should be set to "8".
+ - mentor,ram-bits : Specifies the ram address size. Should be set to "11".
+ - mentor,power : Should be "500". This signifies the controller can supply
+ up to 500mA when operating in host mode.
+ - phys : phandle of the USB phy.
+ - usb_overcurrent : phandle to MUSB over-current note. It should have
+ interrupt number for over-current detection logic.
+
+Optional properties:
+ - microchip,fifo-mode: Specifies layout of internal SRAM for end-point fifos.
+ Should be 0 (default) or 1.
+
+Example:
+ aliases {
+ usb1 = &usb1;
+ phy1 = &usb1_phy;
+ };
+
+ usb1: hsusb1_core@1f8e3000 {
+ compatible = "microchip,pic32mzda-usb";
+ reg = <0x1f8e3000 0x1000>,
+ <0x1f884000 0x1000>;
+ reg-names = "mc", "usbcr";
+ interrupts = <132 IRQ_TYPE_EDGE_RISING>,
+ <133 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc", "dma";
+ dr_mode = "host";
+ mentor,multipoint = <1>;
+ mentor,num-eps = <8>;
+ mentor,ram-bits = <11>;
+ mentor,power = <500>;
+ phys = <&usb1_phy>;
+ clocks = <&rootclk PB5CLK>;
+ clock-names = "usb_clk";
+ usb_overcurrent = <&usb1_overcurrent>;
+ };
+
+ usb1_phy: hsusb1_phy@1f8e4000 {
+ compatible = "usb-nop-xceiv";
+ reg = <0x1f8e4000 0x1000>;
+ clocks = <&rootclk UPLLCLK>;
+ clock-names = "main_clk";
+ clock-frequency = <24000000>;
+ };
+
+ usb1_overcurrent: hsusb1_oc@0 {
+ interrupt-parent = <&gpio1>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+ };
--
1.8.3.1
\
 
 \ /
  Last update: 2016-04-07 13:21    [W:0.090 / U:0.540 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site