lkml.org 
[lkml]   [2016]   [Apr]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 03/10] gpio: stmpe: fix edge and rising/falling edge detection
Date
From: Patrice Chotard <patrice.chotard@st.com>

By cross-checking STMPE 610/801/811/1601/2401/2403 datasheets,
it appears that edge detection and rising/falling edge detection
is not supported by all STMPE variant:

GPIO GPIO
Edge detection rising/falling
edge detection
610 | X | X |
801 | | |
811 | X | X |
1600 | | |
1601 | X | X |
1801 | | X |
2401 | X | X |
2403 | X | X |

Rework stmpe_dbg_show_one() and stmpe_gpio_irq to correctly
take these cases into account.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/gpio/gpio-stmpe.c | 85 +++++++++++++++++++++++++++++++++--------------
1 file changed, 60 insertions(+), 25 deletions(-)

diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
index 5197edf..bfc918c 100644
--- a/drivers/gpio/gpio-stmpe.c
+++ b/drivers/gpio/gpio-stmpe.c
@@ -231,39 +231,74 @@ static void stmpe_dbg_show_one(struct seq_file *s,
gpio, label ?: "(none)",
val ? "hi" : "lo");
} else {
- u8 edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] + num_banks - 1 - (offset / 8);
- u8 rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] - (offset / 8);
- u8 fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] - (offset / 8);
- u8 irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] - (offset / 8);
- bool edge_det;
- bool rise;
- bool fall;
+ u8 edge_det_reg;
+ u8 rise_reg;
+ u8 fall_reg;
+ u8 irqen_reg;
+
+ char *edge_det_values[] = {"edge-inactive",
+ "edge-asserted",
+ "not-supported"};
+ char *rise_values[] = {"no-rising-edge-detection",
+ "rising-edge-detection",
+ "not-supported"};
+ char *fall_values[] = {"no-falling-edge-detection",
+ "falling-edge-detection",
+ "not-supported"};
+ #define NOT_SUPPORTED_IDX 2
+ u8 edge_det = NOT_SUPPORTED_IDX;
+ u8 rise = NOT_SUPPORTED_IDX;
+ u8 fall = NOT_SUPPORTED_IDX;
bool irqen;

- ret = stmpe_reg_read(stmpe, edge_det_reg);
- if (ret < 0)
- return;
- edge_det = !!(ret & mask);
- ret = stmpe_reg_read(stmpe, rise_reg);
- if (ret < 0)
+ switch (stmpe->partnum) {
+ case STMPE610:
+ case STMPE811:
+ case STMPE1601:
+ case STMPE2401:
+ case STMPE2403:
+ edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] +
+ num_banks - 1 - (offset / 8);
+ ret = stmpe_reg_read(stmpe, edge_det_reg);
+ if (ret < 0)
+ return;
+ edge_det = !!(ret & mask);
+
+ case STMPE1801:
+ rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] -
+ (offset / 8);
+ fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] -
+ (offset / 8);
+ ret = stmpe_reg_read(stmpe, rise_reg);
+ if (ret < 0)
+ return;
+ rise = !!(ret & mask);
+ ret = stmpe_reg_read(stmpe, fall_reg);
+ if (ret < 0)
+ return;
+ fall = !!(ret & mask);
+
+ case STMPE801:
+ irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] -
+ (offset / 8);
+ break;
+
+ default:
return;
- rise = !!(ret & mask);
- ret = stmpe_reg_read(stmpe, fall_reg);
- if (ret < 0)
- return;
- fall = !!(ret & mask);
+ }
+
ret = stmpe_reg_read(stmpe, irqen_reg);
if (ret < 0)
return;
irqen = !!(ret & mask);

- seq_printf(s, " gpio-%-3d (%-20.20s) in %s %s %s%s%s",
+ seq_printf(s, " gpio-%-3d (%-20.20s) in %s %13s %13s %25s %25s",
gpio, label ?: "(none)",
val ? "hi" : "lo",
- edge_det ? "edge-asserted" : "edge-inactive",
- irqen ? "IRQ-enabled" : "",
- rise ? " rising-edge-detection" : "",
- fall ? " falling-edge-detection" : "");
+ edge_det_values[edge_det],
+ irqen ? "IRQ-enabled" : "IRQ-disabled",
+ rise_values[rise],
+ fall_values[fall]);
}
}

@@ -322,8 +357,8 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)

stmpe_reg_write(stmpe, statmsbreg + i, status[i]);

- /* Edge detect register is not present on 801 */
- if (stmpe->partnum != STMPE801)
+ /* Edge detect register is not present on 801 and 1801 */
+ if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801)
stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB]
+ i, status[i]);
}
--
1.9.1
\
 
 \ /
  Last update: 2016-04-28 14:21    [W:0.131 / U:33.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site