lkml.org 
[lkml]   [2016]   [Apr]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCHv2] musb_host: fix lockup on rxcsr_h_error
Hi,

On Wed, Apr 27, 2016 at 02:13:56PM -0500, Bin Liu wrote:
> Hi,
>
> On Wed, Apr 27, 2016 at 09:26:10PM +0300, Maxim Uvarov wrote:
> > 2016-04-27 18:46 GMT+03:00 Bin Liu <b-liu@ti.com>:
> > > Hi,
> > >
> > > On Wed, Apr 27, 2016 at 09:51:58AM +0300, Max Uvarov wrote:
> > >> Fix soft lockup when resetting remote device attached
> > >> to usb host. Configuration:
> > >> pppd -> musb hub -> usb-serial -> gsm modem
> > >
> > > I have heard a few reports similar to this symptom, but never been able
> > > to reproduce it on my side.
> > >
> >
> > Ok, I can reproduce it almost very easy.
> >
> > >> When gsm modem resets, musb rolls in incoming rx interrupts
> > >> which does not give any time to other application as result
> > >> it totally lock ups. Solution is to keep original logic for RXCSR_H_ERROR
> > >
> > > Have you looked where exact place in the interrupt routine the execution
> > > has stuck in?
> > >
> >
> > It does not stuck. It goes to that line which print proto error over
> > and over again and
> > nothing stops that. After some time kernel reports lockup. But
> > actually it's not stuck,
> > all cpu time was eaten by executing that handlers.
> >
> >
> > >> and merge RXCSR_DATAERROR and RXCSR_H_ERROR branches to call same code
> > >> for setting rx stall with MUSB_RXCSR_H_WZC_BITS.
> > >
> > > MUSB_RXCSR_H_WZC_BITS itself does not set rx stall, it just ensures
> > > MUSB_RXCSR_H_RXSTALL not to be cleared. Please check its comment in
> > > musb_regs.h.
> > >
> > >>
> > >> Signed-off-by: Max Uvarov <muvarov@gmail.com>
> > >> ---
> > >> v2: use bitwise or for error flags before logical and. (Sergei Shtylyov).
> > >>
> > >> drivers/usb/musb/musb_host.c | 12 +++++-------
> > >> 1 file changed, 5 insertions(+), 7 deletions(-)
> > >>
> > >> diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c
> > >> index c3d5fc9..2d9aa78 100644
> > >> --- a/drivers/usb/musb/musb_host.c
> > >> +++ b/drivers/usb/musb/musb_host.c
> > >> @@ -1592,14 +1592,12 @@ void musb_host_rx(struct musb *musb, u8 epnum)
> > >
> > > What kernel do you use? This line # is away off from upstream kernel.
> > >
> >
> > I did this patch for 4.1 but 4.6 has the same problem and patch
> > cleanly applies to the latest torvalds/linux.git v4.6-rc5. This
> > interrupt handler has the same code. And looks like on 3.14
>
> Yeah, this code hasn't been chaned for year. But in general, it is
> prepfered to create patches on latest kernel to avoid other headache.
>
> > everything worked. I don't have a time to diff 2 versions. Might be
> > regression.
> >
> >
> > >>
> > >> /* stall; record URB status */
> > >> status = -EPIPE;
> > >> + } else if (rx_csr & (MUSB_RXCSR_DATAERROR | MUSB_RXCSR_H_ERROR)) {
> > >>
> > >> - } else if (rx_csr & MUSB_RXCSR_H_ERROR) {
> > >> - dev_dbg(musb->controller, "end %d RX proto error\n", epnum);
> > >> -
> > >> - status = -EPROTO;
> > >> - musb_writeb(epio, MUSB_RXINTERVAL, 0);
> > >> -
> > >> - } else if (rx_csr & MUSB_RXCSR_DATAERROR) {
> > >> + if (rx_csr & MUSB_RXCSR_H_ERROR) {
> > >> + status = -EPROTO;
> > >> + musb_writeb(epio, MUSB_RXINTERVAL, 0);
> > >> + }
> > >
> > > Please help me to understand how this change fixes the issue. I see the
> > > most effect of the change here is directly 'goto finish' so that 'done'
> > > flag is not set, then musb_advance_schedule() is not called. Is this the
> > > case or I missed other important pieces?
> > >
> >
> > Right that is the goal. On this rxcsr_h_error kernel reschedules
> > current interrupt. And that continues forever. For example adding
>
> The MUSB Programming Guide says CPU should clear this MUSB_RXCSR_H_ERROR
> bit, but the current driver doesn't. I am wondering if this causes the
> controller keeps generating the same interrupt. Can you please try the
> following change instead to see if the lockup goes away?
>
> @@ -1870,6 +1870,9 @@ void musb_host_rx(struct musb *musb, u8 epnum)
> status = -EPROTO;
> musb_writeb(epio, MUSB_RXINTERVAL, 0);
>
> + rx_csr &= ~MUSB_RXCSR_H_ERROR;
> + musb_writew(epio, MUSB_RXCSR, rx_csr);

+ goto finish;

Please also add the line above. I will spend more time to understand
what is happening...

First of all, I don't like the idea of merging the two branches, it
makes the code ugly.

Regards,
-Bin.

> +
> } else if (rx_csr & MUSB_RXCSR_DATAERROR) {
>
> if (USB_ENDPOINT_XFER_ISOC != qh->type) {
>
> Regards,
> -Bin.
>
> > msleep() can give some time for other processes. I'm not an expert in
> > this chip but I think that right solution in that case is not try to
> > reschedule and quick and allow hub to make reset and once again init
> > all devices (in my case ppp/pppd also shutdowns and then I bring
> > everything up with script.). The same behavior with dma and pio mode.
> >
> > Regards,
> > Max.
> >
> > > Thanks,
> > > -Bin.
> > >
> > >>
> > >> if (USB_ENDPOINT_XFER_ISOC != qh->type) {
> > >> dev_dbg(musb->controller, "RX end %d NAK timeout\n", epnum);
> > >> --
> > >> 1.9.1
> > >>
> > >> --
> > >> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
> > >> the body of a message to majordomo@vger.kernel.org
> > >> More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
> >
> >
> > --
> > Best regards,
> > Maxim Uvarov

\
 
 \ /
  Last update: 2016-04-28 00:01    [W:0.089 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site