lkml.org 
[lkml]   [2016]   [Apr]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net v3 2/5] drivers: net: cpsw: fix segfault in case of bad phy-handle
Date
From: David Rivshin <drivshin@allworx.com>

If an emac node has a phy-handle property that points to something
which is not a phy, then a segmentation fault will occur when the
interface is brought up. This is because while phy_connect() will
return ERR_PTR() on failure, of_phy_connect() will return NULL.
The common error check uses IS_ERR(), and so missed when
of_phy_connect() fails. The NULL pointer is then dereferenced.

Also, the common error message referenced slave->data->phy_id,
which would be empty in the case of phy-handle. Instead, use the
name of the device_node as a useful identifier. And in the phy_id
case add the error code for completeness.

Fixes: 9e42f715264f ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
---
I would suggest this for -stable. It should apply cleanly as far back
as 4.5, although there is a trivial conflict in 4.4. I can produce a
separate patch against linux-4.4.y if preferred.

Changes since v2:
- new patch, although fixing part of previous patch 2 [1]

Changes since v1 [2]:
- Rebased (no conflicts)
- Added Tested-by from Nicolas Chauvet
- Added Acked-by from Rob Herring for the binding change

[1] http://patchwork.ozlabs.org/patch/613260/
[2] http://patchwork.ozlabs.org/patch/560324/


drivers/net/ethernet/ti/cpsw.c | 37 +++++++++++++++++++++++--------------
1 file changed, 23 insertions(+), 14 deletions(-)

diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index ce0b0ca..5903448 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -1143,33 +1143,42 @@ static void cpsw_slave_open(struct cpsw_slave *slave, struct cpsw_priv *priv)

if (priv->data.dual_emac)
cpsw_add_dual_emac_def_ale_entries(priv, slave, slave_port);
else
cpsw_ale_add_mcast(priv->ale, priv->ndev->broadcast,
1 << slave_port, 0, 0, ALE_MCAST_FWD_2);

- if (slave->data->phy_node)
+ if (slave->data->phy_node) {
slave->phy = of_phy_connect(priv->ndev, slave->data->phy_node,
&cpsw_adjust_link, 0, slave->data->phy_if);
- else
+ if (!slave->phy) {
+ dev_err(priv->dev, "phy \"%s\" not found on slave %d\n",
+ slave->data->phy_node->full_name,
+ slave->slave_num);
+ return;
+ }
+ } else {
slave->phy = phy_connect(priv->ndev, slave->data->phy_id,
&cpsw_adjust_link, slave->data->phy_if);
- if (IS_ERR(slave->phy)) {
- dev_err(priv->dev, "phy %s not found on slave %d\n",
- slave->data->phy_id, slave->slave_num);
- slave->phy = NULL;
- } else {
- phy_attached_info(slave->phy);
-
- phy_start(slave->phy);
-
- /* Configure GMII_SEL register */
- cpsw_phy_sel(&priv->pdev->dev, slave->phy->interface,
- slave->slave_num);
+ if (IS_ERR(slave->phy)) {
+ dev_err(priv->dev,
+ "phy \"%s\" not found on slave %d, err %ld\n",
+ slave->data->phy_id, slave->slave_num,
+ PTR_ERR(slave->phy));
+ slave->phy = NULL;
+ return;
+ }
}
+
+ phy_attached_info(slave->phy);
+
+ phy_start(slave->phy);
+
+ /* Configure GMII_SEL register */
+ cpsw_phy_sel(&priv->pdev->dev, slave->phy->interface, slave->slave_num);
}

static inline void cpsw_add_default_vlan(struct cpsw_priv *priv)
{
const int vlan = priv->data.default_vlan;
const int port = priv->host_port;
u32 reg;
--
2.5.5
\
 
 \ /
  Last update: 2016-04-28 04:01    [W:0.103 / U:16.884 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site