lkml.org 
[lkml]   [2016]   [Apr]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/6] Documentation: DT binding doc for iProc Shared MDIO Controller.
Date
Add DT binding doc for iProc Shared MDIO Controller which
populate all masters to Shared MDIO framework.

Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
---
.../bindings/bus/brcm,iproc-shared-mdio.txt | 76 ++++++++++++++++++++++
1 file changed, 76 insertions(+)
create mode 100644 Documentation/devicetree/bindings/bus/brcm,iproc-shared-mdio.txt

diff --git a/Documentation/devicetree/bindings/bus/brcm,iproc-shared-mdio.txt b/Documentation/devicetree/bindings/bus/brcm,iproc-shared-mdio.txt
new file mode 100644
index 0000000..f455f3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/brcm,iproc-shared-mdio.txt
@@ -0,0 +1,76 @@
+Broadcom iProc Shared MDIO Controller
+
+Required properties:
+- compatible:
+ "brcm,iproc-shared-mdio" for shared MDIO controller.
+- reg: specifies the base physical address and size of the registers
+- reg-names: should be "mdio"
+- #address-cells: must be 1.
+- #size-cells: must be 0.
+
+optional:
+child nodes: Masters are represented as a child node of shared MDIO controller
+and all the PHYs handled by this master are represented as its child node.
+
+Master nodes properties are defined as-
+
+Required properties:
+- compatible: Used to match driver of this PHY.
+- reg: MDIO master ID.
+- #address-cells: must be 1.
+- #size-cells: must be 0.
+
+optional:
+-brcm,phy-internal: if presents, PHYs are internal. Absence shows phy is
+external.
+-brcm,is-c45: if presents, Controller uses Clause-45 to issue MDIO transaction.
+else Controller uses Clause-22 for transactions.
+
+PHY nodes are represented as the child node of Master. Child nodes properties
+are defined as-
+
+Required properties:
+-reg: phy id of attached PHY.
+
+optional:
+There could be additional properties required to configure the specific phy like
+phy-mode in case of gpphy node below. These should be defined here and used by
+respective drivers.
+
+Example:
+iproc_mdio: iproc_mdio@663f0000 {
+ compatible = "brcm,iproc-shared-mdio";
+ reg = <0x6602023c 0x14>;
+ reg-names = "mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata-master@6 {
+ compatible = "brcm,iproc-ns2-sata-phy";
+ reg = <0x6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ brcm,phy-internal;
+
+ sata_phy0: sata-phy@1 {
+ reg = <0x1>;
+ #phy-cells = <0>;
+ };
+
+ sata_phy1: sata-phy@2 {
+ reg = <0x2>;
+ #phy-cells = <0>;
+ };
+ };
+
+ eth-master@0 {
+ compatible = "brcm,iproc-mdio-master-eth";
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gphy0: eth-phy@10 {
+ reg = <0x10>;
+ phy-mode = "mii";
+ };
+ };
+};
--
1.9.1
\
 
 \ /
  Last update: 2016-04-21 11:41    [W:0.126 / U:0.124 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site