lkml.org 
[lkml]   [2016]   [Apr]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/8] mfd: stmpe: Add reset support for all STMPE variant
Date
From: Patrice Chotard <patrice.chotard@st.com>

Reset was only implemented for STMPE1801 variant despite
all variant have a SOFT_RESET bit.

For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7
of SYS_CTRL register.
For STMPE610/811 (which have the same variant id) SOFT_RESET
bit is bit 1 of SYS_CTRL register.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
---
drivers/mfd/stmpe.c | 23 +++++++++++++++--------
drivers/mfd/stmpe.h | 7 +++++--
2 files changed, 20 insertions(+), 10 deletions(-)

diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index c553b73..af682d0 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -735,13 +735,22 @@ static int stmpe1801_enable(struct stmpe *stmpe, unsigned int blocks,
enable ? mask : 0);
}

-static int stmpe1801_reset(struct stmpe *stmpe)
+static int stmpe_reset(struct stmpe *stmpe)
{
+ u16 id_val = stmpe->variant->id_val;
unsigned long timeout;
int ret = 0;
+ u8 reset_bit;
+
+ if (id_val == STMPE811_ID)
+ /* STMPE801 and STMPE610 use bit 1 of SYS_CTRL register */
+ reset_bit = STMPE811_SYS_CTRL_RESET;
+ else
+ /* all other STMPE variant use bit 7 of SYS_CTRL register */
+ reset_bit = STMPE_SYS_CTRL_RESET;

ret = __stmpe_set_bits(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL],
- STMPE1801_MSK_SYS_CTRL_RESET, STMPE1801_MSK_SYS_CTRL_RESET);
+ reset_bit, reset_bit);
if (ret < 0)
return ret;

@@ -750,7 +759,7 @@ static int stmpe1801_reset(struct stmpe *stmpe)
ret = __stmpe_reg_read(stmpe, stmpe->regs[STMPE_IDX_SYS_CTRL]);
if (ret < 0)
return ret;
- if (!(ret & STMPE1801_MSK_SYS_CTRL_RESET))
+ if (!(ret & reset_bit))
return 0;
usleep_range(100, 200);
}
@@ -1074,11 +1083,9 @@ static int stmpe_chip_init(struct stmpe *stmpe)
if (ret)
return ret;

- if (id == STMPE1801_ID) {
- ret = stmpe1801_reset(stmpe);
- if (ret < 0)
- return ret;
- }
+ ret = stmpe_reset(stmpe);
+ if (ret < 0)
+ return ret;

if (stmpe->irq >= 0) {
if (id == STMPE801_ID)
diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
index 406f9f2..4ae343d 100644
--- a/drivers/mfd/stmpe.h
+++ b/drivers/mfd/stmpe.h
@@ -104,6 +104,8 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE_ICR_LSB_EDGE (1 << 1)
#define STMPE_ICR_LSB_GIM (1 << 0)

+#define STMPE_SYS_CTRL_RESET (1 << 7)
+
/*
* STMPE801
*/
@@ -126,6 +128,7 @@ int stmpe_remove(struct stmpe *stmpe);
/*
* STMPE811
*/
+#define STMPE811_ID 0x0811

#define STMPE811_IRQ_TOUCH_DET 0
#define STMPE811_IRQ_FIFO_TH 1
@@ -155,6 +158,8 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE811_REG_GPIO_FE 0x16
#define STMPE811_REG_GPIO_AF 0x17

+#define STMPE811_SYS_CTRL_RESET (1 << 1)
+
#define STMPE811_SYS_CTRL2_ADC_OFF (1 << 0)
#define STMPE811_SYS_CTRL2_TSC_OFF (1 << 1)
#define STMPE811_SYS_CTRL2_GPIO_OFF (1 << 2)
@@ -244,8 +249,6 @@ int stmpe_remove(struct stmpe *stmpe);
#define STMPE1801_REG_GPIO_PULL_UP_MID 0x23
#define STMPE1801_REG_GPIO_PULL_UP_HIGH 0x24

-#define STMPE1801_MSK_SYS_CTRL_RESET (1 << 7)
-
#define STMPE1801_MSK_INT_EN_KPC (1 << 1)
#define STMPE1801_MSK_INT_EN_GPIO (1 << 3)

--
1.9.1
\
 
 \ /
  Last update: 2016-04-19 14:41    [W:0.236 / U:0.232 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site