lkml.org 
[lkml]   [2016]   [Apr]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v2] mmc: sdhci-pci: add Support of Synopsys DWC_MSHC IP
On 04/19/2016 04:18 PM, Prabu Thangamuthu wrote:
> Synopsys DWC_MSHC is compliant with SD Host Specifications. This patch
> is to support DWC_MSHC controller on PCI interface.

There is dwmmc controller for Synopsys DWC_MSHC.
According to commit message, dwmmc controller also is compliant with SD host specifications.

I think it's enough to use "sdhci-dwc".(To prevent confusion.)

>
> Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
> ---
> Change log v2:
> -Removed Synopsys specific PCI device ID's from pci_ids.h.
> -Updated the PCI device ID's in sdhci-pci-core.c.
>
> MAINTAINERS | 7 +
> drivers/mmc/host/Makefile | 3 +-
> drivers/mmc/host/sdhci-dwc-mshc-pci.c | 298 ++++++++++++++++++++++++++++++++++
> drivers/mmc/host/sdhci-dwc-mshc-pci.h | 58 +++++++
> drivers/mmc/host/sdhci-pci-core.c | 14 ++
> 5 files changed, 379 insertions(+), 1 deletion(-)
> create mode 100644 drivers/mmc/host/sdhci-dwc-mshc-pci.c
> create mode 100644 drivers/mmc/host/sdhci-dwc-mshc-pci.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 1d5b4be..b260b97 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9751,6 +9751,13 @@ S: Maintained
> F: include/linux/mmc/dw_mmc.h
> F: drivers/mmc/host/dw_mmc*
>
> +SYNOPSYS SDHCI COMPLIANT DWC MSHC DRIVER
> +M: Prabu Thangamuthu <prabu.t@synopsys.com>
> +M: Manjunath M B <manjumb@synopsys.com>
> +L: linux-mmc@vger.kernel.org
> +S: Maintained
> +F: drivers/mmc/host/sdhci-dwc-mshc*
> +
> SYSTEM TRACE MODULE CLASS
> M: Alexander Shishkin <alexander.shishkin@linux.intel.com>
> S: Maintained
> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
> index af918d2..1d2a3cf 100644
> --- a/drivers/mmc/host/Makefile
> +++ b/drivers/mmc/host/Makefile
> @@ -9,7 +9,8 @@ obj-$(CONFIG_MMC_MXC) += mxcmmc.o
> obj-$(CONFIG_MMC_MXS) += mxs-mmc.o
> obj-$(CONFIG_MMC_SDHCI) += sdhci.o
> obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
> -sdhci-pci-y += sdhci-pci-core.o sdhci-pci-o2micro.o
> +sdhci-pci-y += sdhci-pci-core.o sdhci-pci-o2micro.o \
> + sdhci-dwc-mshc-pci.o

how about using sdhci-pci-XXX?

> obj-$(subst m,y,$(CONFIG_MMC_SDHCI_PCI)) += sdhci-pci-data.o
> obj-$(CONFIG_MMC_SDHCI_ACPI) += sdhci-acpi.o
> obj-$(CONFIG_MMC_SDHCI_PXAV3) += sdhci-pxav3.o
> diff --git a/drivers/mmc/host/sdhci-dwc-mshc-pci.c b/drivers/mmc/host/sdhci-dwc-mshc-pci.c
> new file mode 100644
> index 0000000..e934af4
> --- /dev/null
> +++ b/drivers/mmc/host/sdhci-dwc-mshc-pci.c
> @@ -0,0 +1,298 @@
> +/*
> + * Copyright (C) 2016 Synopsys, Inc.
> + *
> + * Author: Manjunath M B <manjumb@synopsys.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/pci.h>
> +#include <linux/delay.h>
> +#include <linux/module.h>
> +#include <linux/moduleparam.h>
> +
> +#include "sdhci.h"
> +#include "sdhci-pci.h"
> +#include "sdhci-dwc-mshc-pci.h"
> +
> +/*****************************************************************************\
> + * *
> + * Hardware specific clock handling *
> + * *
> +\*****************************************************************************/
> +static const struct sdhci_ops *sdhci_ops; /* Low level hw interface */
> +
> +static void sdhci_set_clock_snps(struct sdhci_host *host,
> + unsigned int clock)
> +{
> + int div = 0;
> + int mul = 0;
> + int div_val = 0;
> + int mul_val = 0;
> + int mul_div_val = 0;
> + int reg = 0;
> + u16 clk = 0;
> + u32 vendor_ptr;
> + unsigned long timeout;
> + u32 tx_clk_phase_val = SDHC_DEF_TX_CLK_PH_VAL;
> + u32 rx_clk_phase_val = SDHC_DEF_RX_CLK_PH_VAL;
> +
> + /* DWC MSHC Specific clock settings */

I think this comment don't need..because this file already is IP specific.

> +
> + /* if clock is less than 25MHz, divided clock is used.
> + * For divided clock, we can use the standard sdhci_set_clock().
> + * For clock above 25MHz, DRP clock is used
> + * Here, we cannot use sdhci_set_clock(), we need to program
> + * TX RX CLOCK DCM DRP for appropriate clock
> + */
> +
> + vendor_ptr = sdhci_readw(host, SDHCI_UHS2_VENDOR);
> +
> + if (clock <= 25000000) {
> + /* Then call generic set_clock */
> + sdhci_ops->set_clock(host, clock);
> + } else {
> +
> + host->mmc->actual_clock = 0;
> +
> + /* Select un-phase shifted clock before reset Tx Tuning DCM*/
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg &= ~SDHC_TX_CLK_SEL_TUNED;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> + mdelay(10);
> +
> + sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
> +
> + if (clock == 0)
> + return;

Why return here? Can this locate above?

> +
> + /* Lets chose the Mulitplier value to be 0x2 */
> + mul = 0x2;
> + for (div = 1; div <= 32; div++) {
> + if (((host->max_clk * mul) / div)
> + <= clock)
> + break;
> + }
> + /*
> + * Set Programmable Clock Mode in the Clock
> + * Control register.
> + */
> + div_val = div - 1;
> + mul_val = mul - 1;
> +
> + host->mmc->actual_clock = (host->max_clk * mul) / div;
> + /* Program the DCM DRP */
> + /* Step 1: Assert DCM Reset */

I think more readable that you write the all steps on here.
/*
* Step1 :...
* Step2 :...

> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg = reg | SDHC_CARD_TX_CLK_DCM_RST;

reg |= SDHC_CARD_...

> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> +
> + /* Step 2: Program the mul and div values in DRP */
> + mul_div_val = (mul_val << 8) | div_val;
> + sdhci_writew(host, mul_div_val, TXRX_CLK_DCM_MUL_DIV_DRP);
> +
> + /* Step 3: issue a dummy read from DRP base 0x00 as per
> + * www.xilinx.com/support/documentation/user_guides/ug191.pdf
> + */
> + reg = sdhci_readw(host, TXRX_CLK_DCM_DRP_BASE_51);

This code is workaroud for issue?

> +
> + /* Step 4: De-Assert reset to DCM */
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg &= ~SDHC_CARD_TX_CLK_DCM_RST;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> +
> + clk |= SDHCI_PROG_CLOCK_MODE | SDHCI_CLOCK_INT_EN;
> + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
> +
> + /* Wait max 20 ms */
> + timeout = 20;
> + while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
> + & SDHCI_CLOCK_INT_STABLE)) {
> + if (timeout == 0) {
> + pr_err("%s: Internal clock never stabilised\n",
> + mmc_hostname(host->mmc));
> + return;
> + }
> + timeout--;
> + mdelay(1);
> + }
> +
> + clk |= SDHCI_CLOCK_CARD_EN;
> + sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
> +
> + /* For some bit-files we may have to do phase shifting for
> + * Tx Clock; Let's do it here
> + */
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg = reg | SDHC_TUNING_TX_CLK_DCM_RST;

Ditto.

> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> + mdelay(10);
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg &= ~SDHC_TUNING_TX_CLK_DCM_RST;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> +
> + /* Select working phase value if clock is <= 50MHz */
> + if (clock <= 50000000) {
> + /*Change the Phase value here */
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg = reg | (SDHC_TUNING_TX_CLK_SEL_MASK &
> + (tx_clk_phase_val << SDHC_TUNING_TX_CLK_SEL_SHIFT));
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> + mdelay(10);
> +
> + /* Program to select phase shifted clock */
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg = reg | SDHC_TX_CLK_SEL_TUNED;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> + mdelay(10);
> + }
> +
> + /* This Clock might have affected the RX CLOCK DCM
> + * used for Phase control; Reset this DCM for proper clock
> + */
> +
> + /* Program the DCM DRP */
> + /* Step 1: Reset the DCM */
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg = reg | SDHC_TUNING_RX_CLK_DCM_RST;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> + mdelay(10);
> + /* Step 2: De-Assert reset to DCM */
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg &= ~SDHC_TUNING_RX_CLK_DCM_RST;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));

Can these codes reuse?
If clock is upper than 50MHz, then only this code is running twice..is it correct?

> +
> + /* For 50Mhz, tuning is not possible.. Lets fix the sampling
> + * Phase of Rx Clock here
> + */
> + if (clock <= 50000000) {
> + /*Change the Phase value here */
> + reg = sdhci_readl(host, (SDHC_DBOUNCE + vendor_ptr));
> + reg &= ~SDHC_TUNING_RX_CLK_SEL_MASK;
> + reg = reg | (SDHC_TUNING_RX_CLK_SEL_MASK &
> + rx_clk_phase_val);
> + sdhci_writew(host, reg, (SDHC_DBOUNCE + vendor_ptr));
> + }
> + mdelay(10);
> + }
> +}
> +
> +static int sdhci_pci_enable_dma_snps(struct sdhci_host *host)
> +{
> + /* DWC MSHC Specific Dma Enabling */

Ditto.. this file is already DWC specific.

> +
> + /* Call generic emable_dma */
> + return sdhci_ops->enable_dma(host);
> +}
> +
> +static void sdhci_pci_set_bus_width_snps(struct sdhci_host *host, int width)
> +{
> + /* DWC MSHC Specific Bus Width Setting */

Ditto.

> +
> + /* Call generic set_bus_width */
> + sdhci_ops->set_bus_width(host, width);
> +}
> +
> +static void sdhci_reset_snps(struct sdhci_host *host, u8 mask)
> +{
> + /* DWC MSHC Specific hci reset */
> +
> + /* Call generic reset */
> + sdhci_ops->reset(host, mask);
> +}
> +static void sdhci_set_uhs_signaling_snps(struct sdhci_host *host,
> + unsigned int timing)
> +{
> + /* DWC MSHC Specific UHS-I Signaling */
> +
> + /* Call generic UHS-I signaling */
> + sdhci_ops->set_uhs_signaling(host, timing);
> +}
> +static void sdhci_pci_hw_reset_snps(struct sdhci_host *host)
> +{
> + /* DWC MSHC Specific hw reset */
> +
> + /* Call generic hw_reset */
> + if (host->ops && host->ops->hw_reset)

Above other host->ops-> didn't check..do you think what's correct?

> + sdhci_ops->hw_reset(host);
> +}
> +static const struct sdhci_ops sdhci_pci_ops_snps = {
> + .set_clock = sdhci_set_clock_snps,
> + .enable_dma = sdhci_pci_enable_dma_snps,
> + .set_bus_width = sdhci_pci_set_bus_width_snps,
> + .reset = sdhci_reset_snps,
> + .set_uhs_signaling = sdhci_set_uhs_signaling_snps,
> + .hw_reset = sdhci_pci_hw_reset_snps,
> +};
> +
> +static int snps_init_clock(struct sdhci_host *host)
> +{
> + int div = 0;
> + int mul = 0;
> + int div_val = 0;
> + int mul_val = 0;
> + int mul_div_val = 0;
> + int reg = 0;
> + u32 vendor_ptr;
> +
> + vendor_ptr = sdhci_readw(host, SDHCI_UHS2_VENDOR);
> +
> + /* Configure the BCLK DRP to get 100 MHZ Clock */
> +
> + /* To get 100MHz from 100MHz input freq,
> + * mul=2 and div=2
> + * Formula: output_clock = (input clock * mul) / div
> + */
> + mul = 2;
> + div = 2;
> + mul_val = mul - 1;
> + div_val = div - 1;
> + /* Program the DCM DRP */
> + /* Step 1: Reset the DCM */
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg = reg | SDHC_BCLK_DCM_RST;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));
> + /* Step 2: Program the mul and div values in DRP */
> + mul_div_val = (mul_val << 8) | div_val;
> + sdhci_writew(host, mul_div_val, BCLK_DCM_MUL_DIV_DRP);
> + /* Step 3: issue a dummy read from DRP base 0x00 as per
> + * http://www.xilinx.com/support/documentation/user_guides/ug191.pdf
> + */
> + reg = sdhci_readw(host, BCLK_DCM_DRP_BASE_51);
> + /* Step 4: De-Assert reset to DCM */
> + /* de assert reset*/
> + reg = sdhci_readl(host, (SDHC_GPIO_OUT + vendor_ptr));
> + reg &= ~SDHC_BCLK_DCM_RST;
> + sdhci_writew(host, reg, (SDHC_GPIO_OUT + vendor_ptr));

I'm not sure but it seems these codes are also simliar to above codes.
If i'm correct, you can reduce the code lines.

> +
> + /* By Default Clocks to MSHC are off..
> + * Before stack applies reset; we need to turn on the clock
> + */
> + sdhci_writew(host, SDHCI_CLOCK_INT_EN, SDHCI_CLOCK_CONTROL);
> +
> + return 0;
> +
> +}
> +
> +int sdhci_pci_probe_slot_snps(struct sdhci_pci_slot *slot)
> +{
> + int ret = 0;
> + struct sdhci_host *host;
> +
> + host = slot->host;
> + sdhci_ops = host->ops;
> + host->ops = &sdhci_pci_ops_snps;
> +
> + /* Board specific clock initialization */
> + ret = snps_init_clock(host);
> + return ret;
> +}
> +EXPORT_SYMBOL_GPL(sdhci_pci_probe_slot_snps);
> diff --git a/drivers/mmc/host/sdhci-dwc-mshc-pci.h b/drivers/mmc/host/sdhci-dwc-mshc-pci.h
> new file mode 100644
> index 0000000..1635bf2
> --- /dev/null
> +++ b/drivers/mmc/host/sdhci-dwc-mshc-pci.h
> @@ -0,0 +1,58 @@
> +/*
> + * Copyright (C) 2016 Synopsys, Inc.
> + *
> + * Author: Manjunath M B <manjumb@synopsys.com>
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#ifndef __SDHCI_DWC_MSHC_PCI_H__
> +#define __SDHCI_DWC_MSHC_PCI_H__
> +
> +#include "sdhci-pci.h"
> +
> +#define SDHCI_UHS2_VENDOR 0xE8
> +
> +#define DRIVER_NAME "sdhci_snps"
What do you use .."snps" or "dwc_mshc"?
As i mentioned, i want not to use "*mshc*" in these patches.

Best Regards,
Jaehoon Chung

> +#define SDHC_DEF_TX_CLK_PH_VAL 4
> +#define SDHC_DEF_RX_CLK_PH_VAL 4
> +
> +/* Synopsys Vendor Specific Registers */
> +#define SDHC_DBOUNCE 0x08
> +#define SDHC_TUNING_RX_CLK_SEL_MASK 0x000000FF
> +#define SDHC_GPIO_OUT 0x34
> +/* HAPS 51 Based implementation */
> +#define SDHC_BCLK_DCM_RST 0x00000001
> +#define SDHC_CARD_TX_CLK_DCM_RST 0x00000002
> +#define SDHC_TUNING_RX_CLK_DCM_RST 0x00000004
> +#define SDHC_TUNING_TX_CLK_DCM_RST 0x00000008
> +#define SDHC_TUNING_TX_CLK_SEL_MASK 0x00000070
> +#define SDHC_TUNING_TX_CLK_SEL_SHIFT 4
> +#define SDHC_TX_CLK_SEL_TUNED 0x00000080
> +
> +/* Offset of BCLK DCM DRP Attributes */
> +/* Every attribute is of 16 bit wide */
> +#define BCLK_DCM_DRP_BASE_51 0x1000
> +
> +#define BCLK_DCM_MUL_DIV_DRP 0x1050
> +#define MUL_MASK_DRP 0xFF00
> +#define DIV_MASK_DRP 0x00FF
> +
> +/* Offset of TX and RX CLK DCM DRP */
> +#define TXRX_CLK_DCM_DRP_BASE_51 0x2000
> +#define TXRX_CLK_DCM_MUL_DIV_DRP 0x2050
> +
> +int sdhci_pci_probe_snps(struct sdhci_pci_chip *chip);
> +int sdhci_pci_probe_slot_snps(struct sdhci_pci_slot *slot);
> +int sdhci_pci_resume_snps(struct sdhci_pci_chip *chip);
> +int sdhci_pci_suspend_snps(struct sdhci_pci_chip *chip);
> +
> +#endif
> diff --git a/drivers/mmc/host/sdhci-pci-core.c b/drivers/mmc/host/sdhci-pci-core.c
> index 79e1901..bfa3b39 100644
> --- a/drivers/mmc/host/sdhci-pci-core.c
> +++ b/drivers/mmc/host/sdhci-pci-core.c
> @@ -31,6 +31,7 @@
> #include "sdhci.h"
> #include "sdhci-pci.h"
> #include "sdhci-pci-o2micro.h"
> +#include "sdhci-dwc-mshc-pci.h"
>
> /*****************************************************************************\
> * *
> @@ -70,6 +71,11 @@ static int ricoh_mmc_resume(struct sdhci_pci_chip *chip)
> msleep(500);
> return 0;
> }
> +/* Synopsys DWC MSHC Controller based SDHCI-PCI */
> +static const struct sdhci_pci_fixes sdhci_snps = {
> + .probe_slot = sdhci_pci_probe_slot_snps,
> + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
> +};
>
> static const struct sdhci_pci_fixes sdhci_ricoh = {
> .probe = ricoh_probe,
> @@ -797,6 +803,14 @@ static const struct sdhci_pci_fixes sdhci_amd = {
>
> static const struct pci_device_id pci_ids[] = {
> {
> + .vendor = PCI_VENDOR_ID_SYNOPSYS,
> + .device = 0xc201, /* Device ID of MSHC EP on Haps51 */
> + .subvendor = PCI_ANY_ID,
> + .subdevice = PCI_ANY_ID,
> + .driver_data = (kernel_ulong_t)&sdhci_snps,
> + },
> +
> + {
> .vendor = PCI_VENDOR_ID_RICOH,
> .device = PCI_DEVICE_ID_RICOH_R5C822,
> .subvendor = PCI_ANY_ID,
>

\
 
 \ /
  Last update: 2016-04-19 13:21    [W:0.099 / U:2.820 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site