lkml.org 
[lkml]   [2016]   [Apr]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH RESEND 1/2] pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
From
Date
Hi Linus, Reddy,

On 4/17/2016 8:34 PM, Yendapally Reddy Dhananjaya Reddy wrote:
> Hi Linus,
>
> On Thu, Apr 14, 2016 at 3:12 PM, Linus Walleij <linus.walleij@linaro.org> wrote:
>> On Thu, Apr 14, 2016 at 9:53 AM, Yendapally Reddy Dhananjaya Reddy
>> <yendapally.reddy@broadcom.com> wrote:
>>> On Wed, Apr 13, 2016 at 6:49 PM, Linus Walleij <linus.walleij@linaro.org> wrote:
>>>> On Tue, Mar 29, 2016 at 5:22 PM, Yendapally Reddy Dhananjaya Reddy
>>>> <yendapally.reddy@broadcom.com> wrote:
>>
>>>>> +static const unsigned int gpio_0_1_pins[] = {24, 25};
>>>>> +static const unsigned int pwm_0_pins[] = {24};
>>>>> +static const unsigned int pwm_1_pins[] = {25};
>>>>
>>>> So either the same pins are used for GPIO or PWM.
>>>> And this pattern persists.
>>>>
>>>> Do you have a brewing GPIO driver for this block as well?
>>>> Is it a separate front-end calling to pinctrl using the
>>>> pinctrl_gpio_* calls or do you plan to patch it into this
>>>> driver?
>>>>
>>>> This is more of a question.
>>>>
>>>
>>> This SoC supports group based configuration and there is a top level register
>>> to select groups. Once the gpio_0_1_pins group is selected, there is one more
>>> register to select between gpio_0_1 and pwm (only four pins). The pins
>>> 24 and 25 are shared between nor pins and gpio at the top group level. Once
>>> gpio group is selected, then we can select to be either gpio or pwm. I missed
>>> these two pins to be added to nor_data_pins and will add in the next version.
>>>
>>> static const unsigned nor_data_pins[] = {0, 1, 2, 3, 4, 5, 6, 7, 8, 9,
>>> 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25};
>>>
>>> NS2_PIN_GROUP(nand, 0, 0, 31, 1, 0),
>>> NS2_PIN_GROUP(nor_data, 0, 0, 31, 1, 1),
>>> NS2_PIN_GROUP(gpio_0_1, 0, 0, 31, 1, 0),
>>>
>>> To select PWM, we need to select gpio and pwm as well.
>>>
>>> gpio: gpio {
>>> function = "gpio";
>>> groups = "gpio_0_1_grp";
>>>
>>> pwm: pwm {
>>> function = "pwm";
>>> groups = "pwm0_grp", "pwm1_grp";
>>> };
>>>
>>> Already available gpio driver "pinctrl-iproc-gpio.c" will be the gpio driver
>>> for this soc as well without pin request.
>>
>> Then you are doing something wrong. Look in pinctrl-iproc-gpio.c:
>>
>> /*
>> * Request the Iproc IOMUX pinmux controller to mux individual pins to GPIO
>> */
>> static int iproc_gpio_request(struct gpio_chip *gc, unsigned offset)
>> {
>> struct iproc_gpio *chip = gpiochip_get_data(gc);
>> unsigned gpio = gc->base + offset;
>>
>> /* not all Iproc GPIO pins can be muxed individually */
>> if (!chip->pinmux_is_supported)
>> return 0;

NS2 does not support GPIO pins to be muxed individually. The call to
iproc_gpio_request should be rejected for NS2 since
'chip->pinmux_is_supported' is false.

>>
>> return pinctrl_request_gpio(gpio);
>> }
>>
>> static void iproc_gpio_free(struct gpio_chip *gc, unsigned offset)
>> {
>> struct iproc_gpio *chip = gpiochip_get_data(gc);
>> unsigned gpio = gc->base + offset;
>>
>> if (!chip->pinmux_is_supported)
>> return;

Same here

>>
>> pinctrl_free_gpio(gpio);
>> }
>>
>> So as you see pinctrl_request_gpio() and pinctrl_free_gpio()
>> are being called.
>>
>> These will in turn call pinmux_request_gpio() and
>> pinmux_free_gpio() to make the backing pin controller
>> mux in the pin as GPIO.
>>
>> pinmux_request_gpio() will end up in pin_request()
>> and at this point:
>>
>> if (gpio_range && ops->gpio_request_enable)
>> /* This requests and enables a single GPIO pin */
>> status = ops->gpio_request_enable(pctldev, gpio_range, pin);
>>
>> As you can see: it will attempt to call the .gpio_request_enable()
>> method of your struct pinmux_ops.
>>
>> But your pinmux ops look like this:
>>
>> +static struct pinmux_ops ns2_pinmux_ops = {
>> + .get_functions_count = ns2_get_functions_count,
>> + .get_function_name = ns2_get_function_name,
>> + .get_function_groups = ns2_get_function_groups,
>> + .set_mux = ns2_pinmux_enable,
>> +};
>>
>> I.e. there is no way that GPIO can be set up as a GPIO line,
>> and you're relying on some other pin control entries in the
>> device tree to do that, which is unnecessarily complicated.

Correct, since NS2 can only support group based GPIO configuration, the
above functions will be rejected because "pinmux_is_supported" is false:

chip->pinmux_is_supported = of_property_read_bool(dev->of_node,
"gpio-ranges");

Here, "gpio-ranges" should never be defined on NS2 DT files.

>>
>> Please consider implementing the .gpio_request_enable callback
>> for this pin multiplexer.
>
> Only 4 GPIO pins are pin configurable. The other GPIO pins are group
> controlled as mentioned in the NS2_PIN_GROUP. A single gpio request will affect
> the other pins in that particular group as the control is available
> to select either "gpio group" or the other. As shown below
> 0x00 selects "gpio_6_7_pins" together
> 0x01 selects "pcie_a3_clk_wak_pins"
> 0x02 selects "nor_addr_4_5_pins"
>
> static const unsigned gpio_6_7_pins[] = {31, 32};
> static const unsigned pcie_a3_clk_wak_pins[] = {31, 32};
> static const unsigned nor_addr_4_5_pins[] = {31, 32};
>
> I tested with not providing the "ranges" property in the gpio node. The
> "iproc_gpio_request" and "iproc_gpio_free" functions returned back as
> "rages" property is not defined.
>
> if (!chip->pinmux_is_supported)
> return 0;
>
> We can support the "iproc_gpio_request" and "iproc_gpio_free" functions for the
> 4 gpios that share the pwm pins only. Please suggest me here.
>
> Thanks,
> Dhananjay
>
>>
>> Yours,
>> Linus Walleij

\
 
 \ /
  Last update: 2016-04-18 20:41    [W:0.140 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site