lkml.org 
[lkml]   [2016]   [Apr]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 2/2] i2c: tegra: proper handling of error cases
On Mon, Apr 18, 2016 at 06:45:55PM +0530, Shardar Shariff Md wrote:
> To summarize the issue observed in error cases:
>
> SW Flow: For i2c message transfer, packet header and data payload is
> posted and then required error/packet completion interrupts are enabled
> later.
>
> HW flow: HW process the packet just after packet header is posted, if
> ARB lost/NACK error occurs (SW will not handle immediately when error
> happens as error interrupts are not enabled at this point). HW assumes
> error is acknowledged and clears current data in FIFO, But SW here posts
> the remaining data payload which still stays in FIFO as stale data
> (data without packet header).
>
> Now once the interrupts are enabled, SW handles ARB lost/NACK error by
> clearing the ARB lost/NACK interrupt. Now HW assumes that SW attended
> the error and will parse/process stale data (data without packet header)
> present in FIFO which causes invalid NACK errors.
>
> Fix: Enable the error interrupts before posting the packet into FIFO
> which make sure HW to not clear the fifo. Also disable the packet mode
> before acknowledging errors (ARB lost/NACK error) to not process any
> stale data. As error interrupts are enabled before posting the packet
> header use spinlock to avoid preempting.
>
> Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
>
> Changes since v1:
> - Align the commit message to 72 characters per line.
> - Removing unnecessary paranthesis.
> - Printing error if tegra_i2c_disable_packet_mode() fails
> is already present and handling error is not taken cared
> in ISR which was done in v2.

I think I didn't express myself very clearly, or gave insufficient
information. The changelog reads easier if you have one entry per
revision. The above would then read:

Changes in v3:
- Printing error if tegra_i2c_disable_packet_mode() fails
is already present and handling error is not taken cared
in ISR which was done in v2.

Changes in v2:
- Align the commit message to 72 characters per line.
- Removing unnecessary paranthesis.

And it should go below the --- separator.

One more nitpick below.

> ---
> drivers/i2c/busses/i2c-tegra.c | 28 ++++++++++++++++++++++++++--
> 1 file changed, 26 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-tegra.c b/drivers/i2c/busses/i2c-tegra.c
> index 6235f16..7922892 100644
> --- a/drivers/i2c/busses/i2c-tegra.c
> +++ b/drivers/i2c/busses/i2c-tegra.c
> @@ -191,6 +191,7 @@ struct tegra_i2c_dev {
> u16 clk_divisor_non_hs_mode;
> bool is_suspended;
> bool is_multimaster_mode;
> + spinlock_t xfer_lock;
> };
>
> static void dvc_writel(struct tegra_i2c_dev *i2c_dev, u32 val, unsigned long reg)
> @@ -510,14 +511,27 @@ err:
> return err;
> }
>
> +static int tegra_i2c_disable_packet_mode(struct tegra_i2c_dev *i2c_dev)
> +{
> + u32 cnfg;
> +
> + cnfg = i2c_readl(i2c_dev, I2C_CNFG);
> + if (cnfg & I2C_CNFG_PACKET_MODE_EN)
> + i2c_writel(i2c_dev, cnfg & ~I2C_CNFG_PACKET_MODE_EN, I2C_CNFG);
> +
> + return tegra_i2c_wait_for_config_load(i2c_dev);
> +}

Since you no longer use the return value you might as well just make the
function return void. I don't feel very strongly about it, though, so
I'll defer to Wolfram.

Thierry
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2016-04-18 16:41    [W:0.038 / U:0.856 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site