lkml.org 
[lkml]   [2016]   [Mar]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
SubjectRe: [PATCH v3 1/2] usb:dwc3: Enable support for 64-bit system
From
Hi Balbi,
If CONFIG_DMA_CMA=y, dma mask is set properly. The issue just happen
when CONFIG_DMA_CMA is not set. In this case, dma mask is not set and
we need this code to check if dma mask should be manually set to 32 or
64.

----
Thang

On Wed, Mar 30, 2016 at 8:09 PM, Felipe Balbi
<felipe.balbi@linux.intel.com> wrote:
>
> Hi,
>
> "Thang Q. Nguyen" <tqnguyen@apm.com> writes:
>> From: "Thang Q. Nguyen" <tqnguyen@apm.com>
>>
>> Add 64-bit DMA operation support to the USB DWC3 driver.
>> First attempt to set the coherent DMA mask for 64-bit DMA.
>> If that failed, attempt again with 32-bit DMA.
>>
>> Changes from v2:
>> - None.
>>
>> Changes from v1:
>> - Remove WARN_ON if dma_mask is NULL
>
> these changes lines should be between the tearline (---) and diffstat
> below.
>
>> Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
>> ---
>> drivers/usb/dwc3/core.c | 15 +++++++++++++++
>> 1 file changed, 15 insertions(+)
>>
>> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
>> index de5e01f..2479c24 100644
>> --- a/drivers/usb/dwc3/core.c
>> +++ b/drivers/usb/dwc3/core.c
>> @@ -831,6 +831,21 @@ static int dwc3_probe(struct platform_device *pdev)
>> dwc->mem = mem;
>> dwc->dev = dev;
>>
>> + /* Try to set 64-bit DMA first */
>> + if (!pdev->dev.dma_mask)
>> + /* Platform did not initialize dma_mask */
>> + ret = dma_coerce_mask_and_coherent(&pdev->dev,
>> + DMA_BIT_MASK(64));
>> + else
>> + ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
>> +
>> + /* If seting 64-bit DMA mask fails, fall back to 32-bit DMA mask */
>> + if (ret) {
>> + ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
>> + if (ret)
>> + return ret;
>> + }
>
> Also, why is it so that you need this now ? glue layers are copying dma
> mask from parent device and that should be set properly. This really
> shouldn't be necessary in dwc3-core; it would mean that glue layer
> didn't set this device up properly.
>
> --
> balbi



--

Thang Q. Nguyen | Staff SW Eng.

C: +849.7684.7606 | O: +848.3770.0640
F: +848.3770.0641 | tqnguyen@apm.com
\
 
 \ /
  Last update: 2016-03-31 10:01    [W:0.084 / U:1.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site