lkml.org 
[lkml]   [2016]   [Mar]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] regulator: s2mps11: Fix invalid minimal selector for buck9 supplying SD card
On Tue, 29 Mar 2016, Krzysztof Kozlowski wrote:

> On 29.03.2016 18:08, Lee Jones wrote:
> > On Mon, 28 Mar 2016, Krzysztof Kozlowski wrote:
> >
> >> The buck9 regulator of S2MPS11 PMIC lacked minimal selector for linear
> >> mapping. The mapping starts from 0x40 (3 V).
> >>
> >> This buck9 provides power to other regulators, including LDO13 and LDO19
> >> which supply the MMC2 (SD card).
> >>
> >> Bootloader initializes the regulator with value of 0xff (5 V) which is
> >> outside of supported voltage range. When (during boot) constraints to
> >> buck9 were applied, the driver wrote value counting from 0x00, not 0x40.
> >> Effectively driver set lower voltage than required leading to SD card
> >> detection errors on Odroid XU3/XU4:
> >> mmc1: card never left busy state
> >> mmc1: error -110 whilst initialising SD card
> >>
> >> Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
> >> Cc: <stable@vger.kernel.org>
> >> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> >>
> >> ---
> >>
> >> The issue can be reproduced on next-20160324 with
> >> bae4fdc88d7f7dda1 (regulator: core: Ensure we are at least in bounds
> >> for our constraints).
> >> ---
> >> drivers/regulator/s2mps11.c | 19 ++++++++++++++++++-
> >> include/linux/mfd/samsung/s2mps11.h | 9 +++++++++
> >> 2 files changed, 27 insertions(+), 1 deletion(-)
> >
> > [...]
> >
> >> diff --git a/include/linux/mfd/samsung/s2mps11.h b/include/linux/mfd/samsung/s2mps11.h
> >> index b288965e8101..3937a932bfe0 100644
> >> --- a/include/linux/mfd/samsung/s2mps11.h
> >> +++ b/include/linux/mfd/samsung/s2mps11.h
> >> @@ -173,10 +173,19 @@ enum s2mps11_regulators {
> >>
> >> #define S2MPS11_LDO_VSEL_MASK 0x3F
> >> #define S2MPS11_BUCK_VSEL_MASK 0xFF
> >> +#define S2MPS11_BUCK9_MIN_VSEL 0x40
> >> #define S2MPS11_ENABLE_MASK (0x03 << S2MPS11_ENABLE_SHIFT)
> >> #define S2MPS11_ENABLE_SHIFT 0x06
> >> #define S2MPS11_LDO_N_VOLTAGES (S2MPS11_LDO_VSEL_MASK + 1)
> >> #define S2MPS11_BUCK_N_VOLTAGES (S2MPS11_BUCK_VSEL_MASK + 1)
> >> +/*
> >> + * Buck9 supports only 32 voltages (values from 0x40 to 0x5F) but bootloader
> >> + * initializes the register with value of 0xff so when probing this would
> >> + * cause a failure (Odroid XU3):
> >> + * vdd_2.8v_ldo: failed to get the current voltage(-22)
> >> + * Instead pretend we support up to 0xff (5 V).
> >> + */
> >> +#define S2MPS11_BUCK9_N_VOLTAGES 192
> >
> > Err... NACK.
> >
> > Please go and fix the bootloader instead of hacking the kernel.
>
> The change is not needed and was an effect of my inaccurate
> understanding of device and driver behaviour. In v2 there is no such
> statement and changes. Instead driver properly uses the mask without
> touching other parts of register.

Very well. Thanks for letting me know.

--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

\
 
 \ /
  Last update: 2016-03-29 12:21    [W:0.057 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site