lkml.org 
[lkml]   [2016]   [Mar]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2] dmaengine: vdma: Add 64 bit addressing support to the driver
Date
Hi Anurag,

On Wednesday 23 Sep 2015 15:12:36 Anurag Kumar Vulisha wrote:
> On Monday, September 21, 2015 9:27 PM Vinod Koul wrote:
> > On Thu, Aug 27, 2015 at 09:19:18PM +0530, Anurag Kumar Vulisha wrote:
> >> This VDMA is a soft ip, which can be programmed to support
> >> 32 bit addressing or greater than 32 bit addressing.
> >>
> >> When the VDMA ip is configured for 32 bit address space the transfer
> >> start address is specified by a single register.
> >
> > would be good to specfiy which one
>
> Will change this in v3

What happened to v3 ? :-)

> >> When the VDMA core is configured for an address space greater than 32
> >> then each start address is specified by a combination of two
> >> registers. The first register specifies the LSB 32 bits of address,
> >> while the next register specifies the MSB 32 bits of address.For
> >> example,5Ch will specify the LSB 32 bits while 60h will specify the
> >> MSB 32 bits of the first start address.So we need to program two
> >> registers at a time.
> >
> > can we have spaces after full stops and commas!
>
> Will take care of this in v3 patch.
>
> >> +/* Since vdma driver is trying to write to a register offset which is
> >> +not a
> >> + * multiple of 64 bits(ex : 0x5c), we are writing as two separate 32
> >> +bits
> >> + * instead of a single 64 bit register write.
> >> + */
> >
> > This is not kernel style for multi-lines, pls refer to
> > Documentation/CodingStyle
>
> Will address this in v3 patch
>
> >> +
> >> +static inline void vdma_desc_write_64(struct xilinx_vdma_chan *chan,
> >> u32 reg,
> >> + u32 value_lsb, u32 value_msb)
> >> +{
> >> + /* Write the lsb 32 bits*/
> >> + writel(value_lsb, chan->xdev->regs + chan->desc_offset + reg);
> >> +
> >> + /* Write the msb 32 bits */
> >> + writel(value_msb, chan->xdev->regs + chan->desc_offset + reg + 4);
> >
> > why not writeq
>
> We are trying to write at a register address(ex:0x5c) which is not aligned
> on 8 bytes boundary.So if I try to use 64 bit write on it,unalignment
> fault is getting generated.To avoid that we are using two separate 32 bit
> writes. We had this discussion in previous versions of this patch with
> Laurent Pinchart .I have also added this exaplanation in the comments above
> this function.
>
> >> + err = of_property_read_u32(node, "xlnx,addrwidth", &addr_width);
> >> +
> >> + if (err < 0) {
> >> + /* Setting addr_width property to default 32 bits */
> >> + addr_width = 32;
> >> + }
> >
> > braces for a single line statement! Also space is redandant before if
> > condition
>
> Will take care of this in v3 patch

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2016-03-21 18:01    [W:0.127 / U:0.088 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site