lkml.org 
[lkml]   [2016]   [Feb]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [v4 05/14] scsi: ufs: separate device and host quirks
Date
> Currently we use the host quirks mechanism in order to
> handle both device and host controller quirks.
> In order to support various of UFS devices we should separate
> handling the device quirks from the host controller's.
>
> Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
> Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
> Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>



I would like to see this patch to be split into two
1. support for device descriptor read
2. support quirks


>
> ---
> drivers/scsi/ufs/Makefile | 2 +-
> drivers/scsi/ufs/ufs.h | 32 +++++++++++
> drivers/scsi/ufs/ufs_quirks.c | 100 ++++++++++++++++++++++++++++++++++
> drivers/scsi/ufs/ufs_quirks.h | 124
> ++++++++++++++++++++++++++++++++++++++++++
> drivers/scsi/ufs/ufshcd.c | 90 +++++++++++++++++++++++++++++-
> drivers/scsi/ufs/ufshcd.h | 10 ++++
> 6 files changed, 356 insertions(+), 2 deletions(-)
> create mode 100644 drivers/scsi/ufs/ufs_quirks.c
> create mode 100644 drivers/scsi/ufs/ufs_quirks.h
>
> diff --git a/drivers/scsi/ufs/Makefile b/drivers/scsi/ufs/Makefile
> index 8303bcc..8570d41 100644
> --- a/drivers/scsi/ufs/Makefile
> +++ b/drivers/scsi/ufs/Makefile
> @@ -1,5 +1,5 @@
> # UFSHCD makefile
> obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o
> -obj-$(CONFIG_SCSI_UFSHCD) += ufshcd.o
> +obj-$(CONFIG_SCSI_UFSHCD) += ufshcd.o ufs_quirks.o
> obj-$(CONFIG_SCSI_UFSHCD_PCI) += ufshcd-pci.o
> obj-$(CONFIG_SCSI_UFSHCD_PLATFORM) += ufshcd-pltfrm.o
> diff --git a/drivers/scsi/ufs/ufs.h b/drivers/scsi/ufs/ufs.h
> index 42c459a..8dd608b 100644
> --- a/drivers/scsi/ufs/ufs.h
> +++ b/drivers/scsi/ufs/ufs.h
> @@ -43,6 +43,7 @@
> #define GENERAL_UPIU_REQUEST_SIZE 32
> #define QUERY_DESC_MAX_SIZE 255
> #define QUERY_DESC_MIN_SIZE 2
> +#define QUERY_DESC_HDR_SIZE 2
> #define QUERY_OSF_SIZE (GENERAL_UPIU_REQUEST_SIZE - \
> (sizeof(struct utp_upiu_header)))
>
> @@ -195,6 +196,37 @@ enum unit_desc_param {
> UNIT_DESC_PARAM_LARGE_UNIT_SIZE_M1 = 0x22,
> };
>
> +/* Device descriptor parameters offsets in bytes*/
> +enum device_desc_param {
> + DEVICE_DESC_PARAM_LEN = 0x0,
> + DEVICE_DESC_PARAM_TYPE = 0x1,
> + DEVICE_DESC_PARAM_DEVICE_TYPE = 0x2,
> + DEVICE_DESC_PARAM_DEVICE_CLASS = 0x3,
> + DEVICE_DESC_PARAM_DEVICE_SUB_CLASS = 0x4,
> + DEVICE_DESC_PARAM_PRTCL = 0x5,
> + DEVICE_DESC_PARAM_NUM_LU = 0x6,
> + DEVICE_DESC_PARAM_NUM_WLU = 0x7,
> + DEVICE_DESC_PARAM_BOOT_ENBL = 0x8,
> + DEVICE_DESC_PARAM_DESC_ACCSS_ENBL = 0x9,
> + DEVICE_DESC_PARAM_INIT_PWR_MODE = 0xA,
> + DEVICE_DESC_PARAM_HIGH_PR_LUN = 0xB,
> + DEVICE_DESC_PARAM_SEC_RMV_TYPE = 0xC,
> + DEVICE_DESC_PARAM_SEC_LU = 0xD,
> + DEVICE_DESC_PARAM_BKOP_TERM_LT = 0xE,
> + DEVICE_DESC_PARAM_ACTVE_ICC_LVL = 0xF,
> + DEVICE_DESC_PARAM_SPEC_VER = 0x10,
> + DEVICE_DESC_PARAM_MANF_DATE = 0x12,
> + DEVICE_DESC_PARAM_MANF_NAME = 0x14,
> + DEVICE_DESC_PARAM_PRDCT_NAME = 0x15,
> + DEVICE_DESC_PARAM_SN = 0x16,
> + DEVICE_DESC_PARAM_OEM_ID = 0x17,
> + DEVICE_DESC_PARAM_MANF_ID = 0x18,
> + DEVICE_DESC_PARAM_UD_OFFSET = 0x1A,
> + DEVICE_DESC_PARAM_UD_LEN = 0x1B,
> + DEVICE_DESC_PARAM_RTT_CAP = 0x1C,
> + DEVICE_DESC_PARAM_FRQ_RTC = 0x1D,
> +};
> +

This list is correct only for UFS 2.0, UFS 1.0 has different offsets.

> /*
> * Logical Unit Write Protect
> * 00h: LU not write protected
> diff --git a/drivers/scsi/ufs/ufs_quirks.c b/drivers/scsi/ufs/ufs_quirks.c
> new file mode 100644
> index 0000000..476ed01
> --- /dev/null
> +++ b/drivers/scsi/ufs/ufs_quirks.c
> @@ -0,0 +1,100 @@
> +/*
> + * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include "ufshcd.h"
> +#include "ufs_quirks.h"
> +
> +static struct ufs_dev_fix ufs_fixups[] = {
> + /* UFS cards deviations table */
> + UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
> UFS_DEVICE_NO_VCCQ),
> + UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
> + UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS),
> + UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
> + UFS_DEVICE_NO_FASTAUTO),
> + UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9C8KBADG",
> + UFS_DEVICE_QUIRK_PA_TACTIVATE),
> + UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9D8KBADG",
> + UFS_DEVICE_QUIRK_PA_TACTIVATE),
> +
> + END_FIX
> +};
> +
> +static int ufs_get_device_info(struct ufs_hba *hba,
> + struct ufs_device_info *card_data)
> +{
> + int err;
> + u8 model_index;
> + u8 str_desc_buf[QUERY_DESC_STRING_MAX_SIZE + 1] = {0};
> + u8 desc_buf[QUERY_DESC_DEVICE_MAX_SIZE];
> +
> + err = ufshcd_read_device_desc(hba, desc_buf,
> + QUERY_DESC_DEVICE_MAX_SIZE);
> + if (err) {
> + dev_err(hba->dev, "%s: Failed reading Device Desc. err = %d\n",
> + __func__, err);
> + goto out;
> + }
> +
> + /*
> + * getting vendor (manufacturerID) and Bank Index in big endian
> + * format
> + */
> + card_data->wmanufacturerid =
> desc_buf[DEVICE_DESC_PARAM_MANF_ID] << 8 |
> + desc_buf[DEVICE_DESC_PARAM_MANF_ID +
> 1];
> +
> + model_index = desc_buf[DEVICE_DESC_PARAM_PRDCT_NAME];
> +
> + err = ufshcd_read_string_desc(hba, model_index, str_desc_buf,
> + QUERY_DESC_STRING_MAX_SIZE,
> ASCII_STD);
> + if (err) {
> + dev_err(hba->dev, "%s: Failed reading Product Name. err =
> %d\n",
> + __func__, err);
> + goto out;
> + }
> +
> + str_desc_buf[QUERY_DESC_STRING_MAX_SIZE] = '\0';
> + strlcpy(card_data->model, (str_desc_buf + QUERY_DESC_HDR_SIZE),
> + min_t(u8, str_desc_buf[QUERY_DESC_LENGTH_OFFSET],
> + MAX_MODEL_LEN));
> +
> + /* Null terminate the model string */
> + card_data->model[MAX_MODEL_LEN] = '\0';
> +
> +out:
> + return err;
> +}

This functionality should go to ufshcd.c , it would be maybe better just read device descriptor as during prob_hba
And quirk will access the loaded descriptor.


> +void ufs_advertise_fixup_device(struct ufs_hba *hba)
> +{
> + int err;
> + struct ufs_dev_fix *f;
> + struct ufs_device_info card_data;
> +
> + card_data.wmanufacturerid = 0;
> +
> + err = ufs_get_device_info(hba, &card_data);
> + if (err) {
> + dev_err(hba->dev, "%s: Failed getting device info. err = %d\n",
> + __func__, err);
> + return;
> + }
> +
> + for (f = ufs_fixups; f->quirk; f++) {
> + if (((f->card.wmanufacturerid == card_data.wmanufacturerid) ||
> + (f->card.wmanufacturerid == UFS_ANY_VENDOR)) &&
> + (STR_PRFX_EQUAL(f->card.model, card_data.model) ||
> + !strcmp(f->card.model, UFS_ANY_MODEL)))
> + hba->dev_quirks |= f->quirk;
> + }
> +}
> +EXPORT_SYMBOL(ufs_advertise_fixup_device);
> diff --git a/drivers/scsi/ufs/ufs_quirks.h b/drivers/scsi/ufs/ufs_quirks.h
> new file mode 100644
> index 0000000..01ab166
> --- /dev/null
> +++ b/drivers/scsi/ufs/ufs_quirks.h
> @@ -0,0 +1,124 @@
> +/*
> + * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#ifndef _UFS_QUIRKS_H_
> +#define _UFS_QUIRKS_H_
> +
> +/* return true if s1 is a prefix of s2 */
> +#define STR_PRFX_EQUAL(s1, s2) !strncmp(s1, s2, strlen(s1))
> +
> +#define UFS_ANY_VENDOR -1
> +#define UFS_ANY_MODEL "ANY_MODEL"
> +
> +#define MAX_MODEL_LEN 16
> +
> +#define UFS_VENDOR_TOSHIBA 0x198
> +#define UFS_VENDOR_SAMSUNG 0x1CE
> +
> +/**
> + * ufs_device_info - ufs device details
> + * @wmanufacturerid: card details
> + * @model: card model
> + */
> +struct ufs_device_info {
> + u16 wmanufacturerid;
> + char model[MAX_MODEL_LEN + 1];
> +};
> +
> +/**
> + * ufs_dev_fix - ufs device quirk info
> + * @card: ufs card details
> + * @quirk: device quirk
> + */
> +struct ufs_dev_fix {
> + struct ufs_device_info card;
> + unsigned int quirk;
> +};
> +
> +#define END_FIX { { 0 }, 0 }
> +
> +/* add specific device quirk */
> +#define UFS_FIX(_vendor, _model, _quirk) \
> + { \
> + .card.wmanufacturerid = (_vendor),\
> + .card.model = (_model), \
> + .quirk = (_quirk), \
> + }
> +
> +/*
> + * If UFS device is having issue in processing LCC (Line Control
> + * Command) coming from UFS host controller then enable this quirk.
> + * When this quirk is enabled, host controller driver should disable
> + * the LCC transmission on UFS host controller (by clearing
> + * TX_LCC_ENABLE attribute of host to 0).
> + */
> +#define UFS_DEVICE_QUIRK_BROKEN_LCC (1 << 0)
> +
> +/*
> + * Some UFS devices don't need VCCQ rail for device operations. Enabling this
> + * quirk for such devices will make sure that VCCQ rail is not voted.
> + */
> +#define UFS_DEVICE_NO_VCCQ (1 << 1)
> +
> +/*
> + * Some vendor's UFS device sends back to back NACs for the DL data frames
> + * causing the host controller to raise the DFES error status. Sometimes
> + * such UFS devices send back to back NAC without waiting for new
> + * retransmitted DL frame from the host and in such cases it might be possible
> + * the Host UniPro goes into bad state without raising the DFES error
> + * interrupt. If this happens then all the pending commands would timeout
> + * only after respective SW command (which is generally too large).
> + *
> + * We can workaround such device behaviour like this:
> + * - As soon as SW sees the DL NAC error, it should schedule the error handler
> + * - Error handler would sleep for 50ms to see if there are any fatal errors
> + * raised by UFS controller.
> + * - If there are fatal errors then SW does normal error recovery.
> + * - If there are no fatal errors then SW sends the NOP command to device
> + * to check if link is alive.
> + * - If NOP command times out, SW does normal error recovery
> + * - If NOP command succeed, skip the error handling.
> + *
> + * If DL NAC error is seen multiple times with some vendor's UFS devices then
> + * enable this quirk to initiate quick error recovery and also silence related
> + * error logs to reduce spamming of kernel logs.
> + */
> +#define UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS (1 << 2)
> +
> +/*
> + * Some UFS devices may not work properly after resume if the link was kept
> + * in off state during suspend. Enabling this quirk will not allow the
> + * link to be kept in off state during suspend.
> + */
> +#define UFS_DEVICE_QUIRK_NO_LINK_OFF (1 << 3)
> +
> +/*
> + * Few Toshiba UFS device models advertise
> RX_MIN_ACTIVATETIME_CAPABILITY as
> + * 600us which may not be enough for reliable hibern8 exit hardware sequence
> + * from UFS device.
> + * To workaround this issue, host should set its PA_TACTIVATE time to 1ms even
> + * if device advertises RX_MIN_ACTIVATETIME_CAPABILITY less than 1ms.
> + */
> +#define UFS_DEVICE_QUIRK_PA_TACTIVATE (1 << 4)
> +
> +/*
> + * Some UFS memory devices may have really low read/write throughput in
> + * FAST AUTO mode, enable this quirk to make sure that FAST AUTO mode is
> + * never enabled for such devices.
> + */
> +#define UFS_DEVICE_NO_FASTAUTO (1 << 5)
> +
> +struct ufs_hba;
> +void ufs_advertise_fixup_device(struct ufs_hba *hba);
> +#endif /* UFS_QUIRKS_H_ */
> diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
> index df0316b..95db156 100644
> --- a/drivers/scsi/ufs/ufshcd.c
> +++ b/drivers/scsi/ufs/ufshcd.c
> @@ -39,9 +39,10 @@
>
> #include <linux/async.h>
> #include <linux/devfreq.h>
> -
> +#include <linux/nls.h>
> #include <linux/of.h>
> #include "ufshcd.h"
> +#include "ufs_quirks.h"
> #include "unipro.h"
>
> #define UFSHCD_ENABLE_INTRS (UTP_TRANSFER_REQ_COMPL |\
> @@ -232,6 +233,16 @@ static inline void ufshcd_disable_irq(struct ufs_hba
> *hba)
> }
> }
>
> +/* replace non-printable or non-ASCII characters with spaces */
> +static inline void ufshcd_remove_non_printable(char *val)
> +{
> + if (!val)
> + return;
> +
> + if (*val < 0x20 || *val > 0x7e)
> + *val = ' ';
> +}
> +
> /*
> * ufshcd_wait_for_register - wait for register value to change
> * @hba - per-adapter interface
> @@ -2021,6 +2032,82 @@ static inline int ufshcd_read_power_desc(struct
> ufs_hba *hba,
> return ufshcd_read_desc(hba, QUERY_DESC_IDN_POWER, 0, buf, size);
> }
>
> +int ufshcd_read_device_desc(struct ufs_hba *hba, u8 *buf, u32 size)
> +{
> + return ufshcd_read_desc(hba, QUERY_DESC_IDN_DEVICE, 0, buf, size);
> +}
> +EXPORT_SYMBOL(ufshcd_read_device_desc);
> +
> +/**
> + * ufshcd_read_string_desc - read string descriptor
> + * @hba: pointer to adapter instance
> + * @desc_index: descriptor index
> + * @buf: pointer to buffer where descriptor would be read
> + * @size: size of buf
> + * @ascii: if true convert from unicode to ascii characters
> + *
> + * Return 0 in case of success, non-zero otherwise
> + */
> +int ufshcd_read_string_desc(struct ufs_hba *hba, int desc_index, u8 *buf,
> + u32 size, bool ascii)
> +{
> + int err = 0;
> +
> + err = ufshcd_read_desc(hba,
> + QUERY_DESC_IDN_STRING, desc_index, buf,
> size);
> +
> + if (err) {
> + dev_err(hba->dev, "%s: reading String Desc failed after %d
> retries. err = %d\n",
> + __func__, QUERY_REQ_RETRIES, err);
> + goto out;
> + }
> +
> + if (ascii) {
> + int desc_len;
> + int ascii_len;
> + int i;
> + char *buff_ascii;
> +
> + desc_len = buf[0];
> + /* remove header and divide by 2 to move from UTF16 to UTF8
> */
> + ascii_len = (desc_len - QUERY_DESC_HDR_SIZE) / 2 + 1;
> + if (size < ascii_len + QUERY_DESC_HDR_SIZE) {
> + dev_err(hba->dev, "%s: buffer allocated size is too
> small\n",
> + __func__);
> + err = -ENOMEM;
> + goto out;
> + }
> +
> + buff_ascii = kmalloc(ascii_len, GFP_KERNEL);
> + if (!buff_ascii) {
> + err = -ENOMEM;
> + goto out_free_buff;
> + }
> +
> + /*
> + * the descriptor contains string in UTF16 format
> + * we need to convert to utf-8 so it can be displayed
> + */
> + utf16s_to_utf8s((wchar_t *)&buf[QUERY_DESC_HDR_SIZE],
> + desc_len - QUERY_DESC_HDR_SIZE,
> + UTF16_BIG_ENDIAN, buff_ascii, ascii_len);

Don't we need to load nls for that? (probably no, just asking).

> + /* replace non-printable or non-ASCII characters with spaces */
> + for (i = 0; i < ascii_len; i++)
> + ufshcd_remove_non_printable(&buff_ascii[i]);
> +
> + memset(buf + QUERY_DESC_HDR_SIZE, 0,
> + size - QUERY_DESC_HDR_SIZE);
> + memcpy(buf + QUERY_DESC_HDR_SIZE, buff_ascii, ascii_len);
> + buf[QUERY_DESC_LENGTH_OFFSET] = ascii_len +
> QUERY_DESC_HDR_SIZE;
> +out_free_buff:
> + kfree(buff_ascii);
> + }
> +out:
> + return err;
> +}
> +EXPORT_SYMBOL(ufshcd_read_string_desc);
> +
> /**
> * ufshcd_read_unit_desc_param - read the specified unit descriptor parameter
> * @hba: Pointer to adapter instance
> @@ -4505,6 +4592,7 @@ static int ufshcd_probe_hba(struct ufs_hba *hba)
> if (ret)
> goto out;
>
> + ufs_advertise_fixup_device(hba);
> /* UFS device is also active now */
> ufshcd_set_ufs_dev_active(hba);
> ufshcd_force_reset_auto_bkops(hba);
> diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
> index 27ae395..b0c7e8b 100644
> --- a/drivers/scsi/ufs/ufshcd.h
> +++ b/drivers/scsi/ufs/ufshcd.h
> @@ -470,6 +470,9 @@ struct ufs_hba {
>
> unsigned int quirks; /* Deviations from standard UFSHCI spec. */
>
> + /* Device deviations from standard UFS device spec. */
> + unsigned int dev_quirks;
> +
> wait_queue_head_t tm_wq;
> wait_queue_head_t tm_tag_wq;
> unsigned long tm_condition;
> @@ -678,6 +681,13 @@ static inline int ufshcd_dme_peer_get(struct ufs_hba
> *hba,
> return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_PEER);
> }
>
> +int ufshcd_read_device_desc(struct ufs_hba *hba, u8 *buf, u32 size);
> +
> +#define ASCII_STD true
> +
> +int ufshcd_read_string_desc(struct ufs_hba *hba, int desc_index, u8 *buf,
> + u32 size, bool ascii);
> +
> /* Expose Query-Request API */
> int ufshcd_query_flag(struct ufs_hba *hba, enum query_opcode opcode,
> enum flag_idn idn, bool *flag_res);
> --
> 1.8.5.2
>
> --
> QUALCOMM ISRAEL, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
> --
> To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html

\
 
 \ /
  Last update: 2016-02-09 18:21    [W:0.130 / U:1.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site