lkml.org 
[lkml]   [2016]   [Feb]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4] iio: adc: Add TI ADS1015 ADC driver support
On Mon, Feb 08, 2016 at 04:44:02PM +0200, Daniel Baluta wrote:
> On Mon, Feb 8, 2016 at 12:25 PM, Wolfram Sang <wsa@the-dreams.de> wrote:
> > On Fri, Feb 05, 2016 at 06:32:45PM -0600, Michael Welling wrote:
> >> On Fri, Feb 05, 2016 at 09:32:34PM +0200, Daniel Baluta wrote:
> >> > >> +static int ads1015_read_raw(struct iio_dev *indio_dev,
> >> > >> + struct iio_chan_spec const *chan, int *val,
> >> > >> + int *val2, long mask)
> >> > >> +{
> >> > >> + int ret, idx;
> >> > >> + struct ads1015_data *data = iio_priv(indio_dev);
> >> > >> +
> >> > >> + mutex_lock(&data->lock);
> >> > >> + switch (mask) {
> >> > >> + case IIO_CHAN_INFO_RAW:
> >> > >> + if (iio_buffer_enabled(indio_dev)) {
> >> > >> + ret = -EBUSY;
> >> > >> + break;
> >> > >> + }
> >> > >> +
> >> > >> + ret = ads1015_set_power_state(data, true);
> >> > >> + if (ret < 0)
> >> > >> + break;
> >> > >
> >> > > Just tested the driver on a Dragonboard 410C with a robotics mezzanine that I
> >> > > designed.
> >> > >
> >> > > The above ads1015_set_power_state(data, true) is always returning -EINVAL.
> >> > >
> >> > > Any ideas why that would be happening?
> >> > > I think it may be the return from pm_runtime_get_sync?
> >> >
> >> > Can you confirm that pm_runtime_get_sync fails? Using some printk?
> >> >
> >> > Also adding printks in suspend/resume function would be helpful. Do
> >> > you have CONFIG_PM enabled?
> >> >
> >>
> >> Indeed it is the pm_runtime_get_sync that fails with a -EINVAL.
>
> Can you check the output of:
> $ cat /sys/bus/iio/devices/iio:device0/power/runtime_status
>
> * after insmod

root@dragonboard-410c:~# cat /sys/bus/iio/devices/iio:device0/power/runtime_status
unsupported

> * after a reading from sysfs

root@dragonboard-410c:~# cat /sys/bus/iio/devices/iio:device0/power/runtime_status
unsupported

>
> >>
> >> > >
> >> > > When I comment out the break the readings come back but are not updated continually.
> >> > > If I read in_voltage0-voltage1_raw then in_voltage0_raw the value is updated.
> >> >
> >> > I guess this is normal if set_power_state fails.
> >>
> >> The hwmod driver works fine BTW.
> >>
> >> My guess is there is an issue with the qup i2c driver seeing as it has worked on
> >> other system without issue.
> >>
> >> CC'd some the latest developer on the qup i2c driver.
> >>
> >> I2C guys have any ideas on this?
> >>
> >
> > Adding some more people who recently worked on this. Might be nice to
> > know which kernel version you are using.

\
 
 \ /
  Last update: 2016-02-08 18:01    [W:0.135 / U:0.548 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site