lkml.org 
[lkml]   [2016]   [Feb]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] mmc: sdhci-tegra: Set DMA mask
Date
On Friday 26 February 2016 16:24:34 Alexandre Courbot wrote:
> On Thu, Feb 25, 2016 at 11:52 PM, Arnd Bergmann <arnd@arndb.de> wrote:
> >> Actually even if we specify a dma-ranges on the parent DT node, the
> >> DMA range will still be limited to 32 bits because of the following
> >> code in of_dma_configure():
> >>
> >> /*
> >> * Set default coherent_dma_mask to 32 bit. Drivers are expected to
> >> * setup the correct supported mask.
> >> */
> >> if (!dev->coherent_dma_mask)
> >> dev->coherent_dma_mask = DMA_BIT_MASK(32);
> >>
> >> /*
> >> * Set it to coherent_dma_mask by default if the architecture
> >> * code has not set it.
> >> */
> >> if (!dev->dma_mask)
> >> dev->dma_mask = &dev->coherent_dma_mask;
> >>
> >> ....
> >> /* gets dma-ranges into dma_addr and size */
> >> ....
> >>
> >>
> >> *dev->dma_mask = min((*dev->dma_mask),
> >> DMA_BIT_MASK(ilog2(dma_addr + size)));
> >>
> >> So unless the DMA mask is set on the device before of_dma_configure()
> >> is called, the min() statement will choose the 32 bits mask that has
> >> been previously set. So IIUC in any case, the driver will need to call
> >> dma_set_mask()
> >
> > Yes, the driver definitely has to call dma_set_mask(), the property of
> > the parent bus is used to make that fail when the bus doesn't support
> > it.
>
> And that's where things seem to stop working: the driver's probe
> function is invoked by the platform bus, *after* of_dma_configure() is
> called. So unless I am missing something there is no way for the
> driver to set the DMA mask in such a way that of_dma_configure() can
> see it and do the right thing.
>
> In other words, most of the DMA mask logic in of_dma_configure()
> doesn't seem to have any effect (and a 32 bits mask will be set), at
> least on the platform bus.

That is correct: of_dma_configure has to set a 32-bit DMA mask
because that is the default that we expect to see in Linux drivers.

A lot of drivers don't call dma_set_mask() at all, so this is
the most reasonable value that typically works, unless the
device is more limited, or you want the extra performance you
get on devices that actually support a bigger mask.

> >> Can I have your thoughts on this? Am I missing something?
> >
> > One point: I think the dma_set_mask() probably should be in the
> > generic part of the sdhci driver, not the tegra specific portion.
>
> Ok, but then how does the generic part of the driver knows which DMA
> mask applies to the device?

If dma_set_mask() succeeds when passed a 64-bit mask, the driver
can pass high addresses into dma_map_*() and put the result into
the 64-bit DMA registers of the device. That is all the driver
needs to know here.

When the bus is more limited than the device, we either have
an swiotlb/iommu that will use bounce buffers to map dma_map_* work
anyway (using low DMA addresses for high memory), or we don't have
an swiotlb and the dma_set_mask() operation has to fail.

Arnd

\
 
 \ /
  Last update: 2016-02-26 13:01    [W:1.332 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site