lkml.org 
[lkml]   [2016]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: ATH9 driver issues on ARM64
Date
Sorry, Forgot to add kernel version, we are using 4.6 kernel. 

> Hi,
> Can any one tell, when exactly the chip sends ASSERT & DEASSERT in driver.
> It might help us to debug issue further.
>
> Thanks & Regards,
> Bharat
>
> > > > [+cc Kalle, ath9k list]
> >
> > Thanks, but please also CC linux-wireless. Full thread below for the folks there.
> >
> > >> On Thu, Dec 08, 2016 at 01:49:42PM +0000, Bharat Kumar Gogada wrote:
> > >> > Hi,
> > >> >
> > >> > Did anyone test Atheros ATH9
> > >> > driver(drivers/net/wireless/ath/ath9k/)
> > >> > on ARM64. The end point is TP link wifi card with which supports
> > >> > only legacy interrupts.
> > >>
> > >> If it works on other arches and the arm64 PCI enumeration works, my
> > >> first guess would be an INTx issue, e.g., maybe the driver is
> > >> waiting for an interrupt that never arrives.
> > > We are not sure for now.
> > >>
> > >> > We are trying to test it on ARM64 with
> > >> > (drivers/pci/host/pcie-xilinx-nwl.c) as root port.
> > >> >
> > >> > EP is getting enumerated and able to link up.
> > >> >
> > >> > But when we start scan system gets hanged.
> > >>
> > >> When you say the system hangs when you start a scan, I assume you
> > >> mean a wifi scan, not the PCI enumeration. A problem with a wifi
> > >> scan might cause a *process* to hang, but it shouldn't hang the
> > >> entire system.
> > >>
> > > Yes wifi scan.
> > >> > When we took trace we see that after we start scan assert message
> > >> > is sent but there is no de assert from end point.
> > >>
> > >> Are you talking about a trace from a PCIe analyzer? Do you see an
> > >> Assert_INTx PCIe message on the link?
> > >>
> > > Yes lecroy trace, yes we do see Assert_INTx and Deassert_INTx
> > > happening
> > when we do interface link up.
> > > When we have less debug prints in Atheros driver, and do wifi scan
> > > we see Assert_INTx but never Deassert_INTx,
> > >> > What might cause end point not sending de assert ?
> > >>
> > >> If the endpoint doesn't send a Deassert_INTx message, I expect that
> > >> would mean the driver didn't service the interrupt and remove the
> > >> condition that caused the device to assert the interrupt in the
> > >> first place.
> > >>
> > >> If the driver didn't receive the interrupt, it couldn't service it,
> > >> of course. You could add a printk in the ath9k interrupt service
> > >> routine to see if you ever get there.
> > >>
> > > The interrupt behavior is changing w.r.t amount of debug prints we
> > > add. (I kept many prints to aid debug) root@Xilinx-ZCU102-2016_3:~#
> > > iw dev
> > wlan0 scan
> > > [ 83.064675] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.069486] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.074257] ath9k_hw_kill_interrupts 793
> > > [ 83.078260] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.083107] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.087882] ath9k_hw_kill_interrupts 793
> > > [ 83.095450] ath9k_hw_enable_interrupts 821
> > > [ 83.099557] ath9k_hw_enable_interrupts 825
> > > [ 83.103721] ath9k_hw_enable_interrupts 832
> > > [ 83.107887] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.112748] AR_SREV_9100 0
> > > [ 83.115438] ath9k_hw_enable_interrupts 848
> > > [ 83.119607] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.124389] ath9k_hw_intrpend 762
> > > [ 83.127761] (AR_SREV_9340(ah) val 0
> > > [ 83.131234] ath9k_hw_intrpend 767
> > > [ 83.134628] ath_isr 603
> > > [ 83.137134] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.141995] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.146771] ath9k_hw_kill_interrupts 793
> > > [ 83.150864] ath9k_hw_enable_interrupts 821
> > > [ 83.154971] ath9k_hw_enable_interrupts 825
> > > [ 83.159135] ath9k_hw_enable_interrupts 832
> > > [ 83.163300] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.168161] AR_SREV_9100 0
> > > [ 83.170852] ath9k_hw_enable_interrupts 848
> > > [ 83.170855] ath9k_hw_intrpend 762
> > > [ 83.178398] (AR_SREV_9340(ah) val 0
> > > [ 83.181873] ath9k_hw_intrpend 767
> > > [ 83.185265] ath_isr 603
> > > [ 83.187773] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.192635] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.197411] ath9k_hw_kill_interrupts 793
> > > [ 83.201414] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.206258] ath9k_hw_enable_interrupts 821
> > > [ 83.210368] ath9k_hw_enable_interrupts 825
> > > [ 83.214531] ath9k_hw_enable_interrupts 832
> > > [ 83.218698] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.223558] AR_SREV_9100 0
> > > [ 83.226243] ath9k_hw_enable_interrupts 848
> > > [ 83.226246] ath9k_hw_intrpend 762
> > > [ 83.233794] (AR_SREV_9340(ah) val 0
> > > [ 83.237268] ath9k_hw_intrpend 767
> > > [ 83.240661] ath_isr 603
> > > [ 83.243169] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.248030] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.252806] ath9k_hw_kill_interrupts 793
> > > [ 83.256811] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.261651] ath9k_hw_enable_interrupts 821
> > > [ 83.265753] ath9k_hw_enable_interrupts 825
> > > [ 83.269919] ath9k_hw_enable_interrupts 832
> > > [ 83.274083] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.278945] AR_SREV_9100 0
> > > [ 83.281630] ath9k_hw_enable_interrupts 848
> > > [ 83.281633] ath9k_hw_intrpend 762
> > > [ 83.281634] (AR_SREV_9340(ah) val 0
> > > [ 83.281637] ath9k_hw_intrpend 767
> > > [ 83.281648] ath_isr 603
> > > [ 83.281649] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.281651] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.281654] ath9k_hw_kill_interrupts 793
> > > [ 83.312192] ath9k: ath9k_ioread32 ffffff800a400024
> > > [ 83.317030] ath9k_hw_enable_interrupts 821
> > > [ 83.321132] ath9k_hw_enable_interrupts 825
> > > [ 83.325297] ath9k_hw_enable_interrupts 832
> > > [ 83.329463] ath9k: ath9k_iowrite32 ffffff800a400024
> > > [ 83.334324] AR_SREV_9100 0
> > > [ 83.337014] ath9k_hw_enable_interrupts 848
> > > ..
> > > ..
> > > This log continues until I turn off board without obtaining scanning result.
> > >
> > > In between I get following cpu stall outputs :
> > > 230.457179] INFO: rcu_sched self-detected stall on CPU
> > > [ 230.457185] 2-...: (31314 ticks this GP)
> > idle=2d1/140000000000001/0 softirq=1400/1400 fqs=36713
> > > [ 230.457189] (t=36756 jiffies g=161 c=160 q=16169)
> > > [ 230.457191] Task dump for CPU 2:
> > > [ 230.457196] kworker/u8:4 R running task 0 1342 2 0x00000002
> > > [ 230.457207] Workqueue: phy0 ieee80211_scan_work [ 230.457208]
> > > Call
> > > trace:
> > > [ 230.457214] [<ffffff8008089860>] dump_backtrace+0x0/0x198 [
> > > 230.457219] [<ffffff8008089a0c>] show_stack+0x14/0x20 [ 230.457224]
> > > [<ffffff80080c0930>] sched_show_task+0x98/0xf8 [ 230.457228]
> > > [<ffffff80080c2628>] dump_cpu_task+0x40/0x50 [ 230.457233]
> > > [<ffffff80080e14a8>] rcu_dump_cpu_stacks+0xa0/0xf0 [ 230.457239]
> > > [<ffffff80080e4cd8>] rcu_check_callbacks+0x468/0x748 [ 230.457243]
> > > [<ffffff80080e7cfc>] update_process_times+0x3c/0x68 [ 230.457249]
> > > [<ffffff80080f6dfc>] tick_sched_handle.isra.5+0x3c/0x50
> > > [ 230.457253] [<ffffff80080f6e54>] tick_sched_timer+0x44/0x90 [
> > > 230.457257] [<ffffff80080e86b0>] __hrtimer_run_queues+0xf0/0x178
> > > ** 10 printk messages dropped ** [ 230.457302] f8c0:
> > > 0000000000000000 0000000005f5e0ff 000000000001379a
> 3866666666666620
> > > [ 230.457306]
> > > f8e0: ffffff800a1b4065 0000000000000006 ffffff800a129000
> > > ffffffc87b8010a8 [ 230.457310] f900: ffffff808a1b4057
> > > ffffff800a1c3000 ffffff800a1b3000 ffffff800a13b000 [ 230.457314]
> > > f920: 0000000000000140 0000000000000006 ffffff800a1b3b10
> > > ffffff800a1c39e8 [ 230.457318] f940: 000000000000002f
> > > ffffff800a1b8a98 ffffff800a1b3ae8 ffffffc87b07f990 [ 230.457322]
> > > f960: ffffff80080d6230 ffffffc87b07f990 ffffff80080d6234
> > > 0000000060000145
> > > ** 1 printk messages dropped ** [ 230.457329] [<ffffff8008085720>]
> > > el1_irq+0xa0/0x100
> > > ** 9 printk messages dropped ** [ 230.457373] [<ffffff800885ad60>]
> > > ieee80211_hw_config+0x50/0x290 [ 230.457377] [<ffffff8008863690>]
> > > ieee80211_scan_work+0x1f8/0x480 [ 230.457383] [<ffffff80080b15d0>]
> > > process_one_work+0x120/0x378 [ 230.457386] [<ffffff80080b1870>]
> > > worker_thread+0x48/0x4b0 [ 230.457391] [<ffffff80080b7108>]
> > > kthread+0xd0/0xe8 [ 230.457395] [<ffffff8008085dd0>]
> > ret_from_fork+0x10/0x40
> > > [ 230.480389] ath9k_hw_intrpend 762
> > >
> > >
> > > [ 545.487987] ath9k: ath9k_ioread32 ffffff800a400024 [ 545.526189]
> > > INFO: rcu_sched self-detected stall on CPU
> > > [ 545.526195] 2-...: (97636 ticks this GP)
> > idle=2d1/140000000000001/0 softirq=1400/1400 fqs=115374
> > > [ 545.526199] (t=115523 jiffies g=161 c=160 q=51066)
> > > [ 545.526201] Task dump for CPU 2:
> > > [ 545.526206] kworker/u8:4 R running task 0 1342 2 0x00000002
> > > ** 3 printk messages dropped ** [ 545.526231] [<ffffff8008089a0c>]
> > > show_stack+0x14/0x20
> > > ** 9 printk messages dropped ** [ 545.526280] [<ffffff80086a71e8>]
> > > arch_timer_handler_phys+0x30/0x40 [ 545.526284]
> > > [<ffffff80080dbe18>]
> > > handle_percpu_devid_irq+0x78/0xa0 [ 545.526291]
> > > [<ffffff80080d760c>]
> > > generic_handle_irq+0x24/0x38 [ 545.526296] [<ffffff80080d7944>]
> > > __handle_domain_irq+0x5c/0xb8 [ 545.526299] [<ffffff80080824bc>]
> > > gic_handle_irq+0x64/0xc0 [ 545.526302] Exception
> > > stack(0xffffffc87b07f870
> > to 0xffffffc87b07f990)
> > > [ 545.526306] f860: 0000000000009732 ffffff800a1eaaa8
> > > ** 8 printk messages dropped ** [ 545.526341] f980:
> > > ffffff800a1c39e8
> > > 0000000000000036 [ 545.526345] [<ffffff8008085720>]
> > > el1_irq+0xa0/0x100 [ 545.526349] [<ffffff80080d6234>]
> > > console_unlock+0x384/0x5b0 [ 545.526353] [<ffffff80080d673c>]
> > > vprintk_emit+0x2dc/0x4b0 [ 545.526357] [<ffffff80080d6a50>]
> > > vprintk_default+0x38/0x40 [ 545.526362] [<ffffff8008129704>]
> > > printk+0x58/0x60 [ 545.526366] [<ffffff800859e3e4>]
> > > ath9k_iowrite32+0x9c/0xa8 [ 545.526372] [<ffffff80085c7ca8>]
> > > ath9k_hw_kill_interrupts+0x28/0xf0
> > > [ 545.526376] [<ffffff80085a18ec>] ath_reset+0x24/0x68
> > > ** 2 printk messages dropped ** [ 545.526391] [<ffffff800885ad60>]
> > ieee80211_hw_config+0x50/0x290
> > > ** 11 printk messages dropped ** [ 545.532834]
> > > ath9k_hw_kill_interrupts
> > 793
> > > [ 545.532890] ath9k_hw_enable_interrupts 821
> > >
> > >
> > > But if we have less debug prints it does not reach EP handler
> > > sometimes, due to following Condition in "kernel/irq/chip.c" in
> > > function handle_simple_irq
> > >
> > > if (unlikely(!desc->action || irqd_irq_disabled(&desc->irq_data))) {
> > > desc->istate |= IRQS_PENDING;
> > > goto out_unlock;
> > > }
> > > Here irqd_irq_disabled is being set to 1.
> > >
> > > With lesser debug prints it stops after following prints:
> > > root@Xilinx-ZCU102-2016_3:~# iw dev wlan0 scan
> > > [ 54.781045] ath9k_hw_kill_interrupts 793
> > > [ 54.785007] ath9k_hw_kill_interrupts 793
> > > [ 54.792535] ath9k_hw_enable_interrupts 821
> > > [ 54.796642] ath9k_hw_enable_interrupts 825
> > > [ 54.800807] ath9k_hw_enable_interrupts 832
> > > [ 54.804973] AR_SREV_9100 0
> > > [ 54.807663] ath9k_hw_enable_interrupts 848
> > > [ 54.811843] ath9k_hw_intrpend 762
> > > [ 54.815211] (AR_SREV_9340(ah) val 0
> > > [ 54.818684] ath9k_hw_intrpend 767
> > > [ 54.822078] ath_isr 603
> > > [ 54.824587] ath9k_hw_kill_interrupts 793
> > > [ 54.828601] ath9k_hw_enable_interrupts 821
> > > [ 54.832750] ath9k_hw_enable_interrupts 825
> > > [ 54.836916] ath9k_hw_enable_interrupts 832
> > > [ 54.841082] AR_SREV_9100 0
> > > [ 54.843772] ath9k_hw_enable_interrupts 848
> > > [ 54.843775] ath9k_hw_intrpend 762
> > > [ 54.851319] (AR_SREV_9340(ah) val 0
> > > [ 54.854793] ath9k_hw_intrpend 767
> > > [ 54.858185] ath_isr 603
> > > [ 54.860696] ath9k_hw_kill_interrupts 793
> > > [ 54.864776] ath9k_hw_enable_interrupts 821
> > > [ 54.867061] ath9k_hw_kill_interrupts 793
> > > [ 54.872870] ath9k_hw_enable_interrupts 825
> > > [ 54.877036] ath9k_hw_enable_interrupts 832
> > > [ 54.881202] AR_SREV_9100 0
> > > [ 54.883892] ath9k_hw_enable_interrupts 848
> > > [ 75.963129] INFO: rcu_sched detected stalls on CPUs/tasks:
> > > [ 75.968602] 0-...: (2 GPs behind) idle=9d5/140000000000001/0
> > softirq=1103/1109 fqs=519
> > > [ 75.976675] (detected by 2, t=5274 jiffies, g=64, c=63, q=11)
> > > [ 75.982485] Task dump for CPU 0:
> > > [ 75.985696] ksoftirqd/0 R running task 0 3 2 0x00000002
> > > [ 75.992726] Call trace:
> > > [ 75.995165] [<ffffff8008086b3c>] __switch_to+0xc4/0xd0
> > > [ 76.000281] [<ffffffc87b830500>] 0xffffffc87b830500
> > > [ 139.059027] INFO: rcu_sched detected stalls on CPUs/tasks:
> > > [ 139.064430] 0-...: (2 GPs behind) idle=9d5/140000000000001/0
> > softirq=1103/1109 fqs=2097
> > > [ 139.072593] (detected by 2, t=21049 jiffies, g=64, c=63, q=11)
> > > [ 139.078489] Task dump for CPU 0:
> > > [ 139.081700] ksoftirqd/0 R running task 0 3 2 0x00000002
> > > [ 139.088731] Call trace:
> > > [ 139.091165] [<ffffff8008086b3c>] __switch_to+0xc4/0xd0 [
> > > 139.096285] [<ffffffc87b830500>] 0xffffffc87b830500
> > >
> > >
> > >> > We are not seeing any issues on 32-bit ARM platform and X86
> > >> > platform.
> > >>
> > >> Can you collect a dmesg log (or, if the system hang means you can't
> > >> collect that, a console log with "ignore_loglevel"), and "lspci -vv"
> > >> output as root? That should have clues about whether the INTx got
> > >> routed correctly. /proc/interrupts should also show whether we're
> > >> receiving interrupts from the device.
> > >
> > > Here is the lspci output:
> > > 00:00.0 PCI bridge: Xilinx Corporation Device d022 (prog-if 00
> > > [Normal
> > decode])
> > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> > ParErr- Stepping- SERR- FastB2B- DisINTx-
> > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR- INTx-
> > > Latency: 0
> > > Interrupt: pin A routed to IRQ 224
> > > Bus: primary=00, secondary=01, subordinate=0c, sec-latency=0
> > > I/O behind bridge: 00000000-00000fff
> > > Memory behind bridge: e0000000-e00fffff
> > > Prefetchable memory behind bridge: 00000000fff00000-
> > 00000000000fffff
> > > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > <TAbort- <MAbort- <SERR- <PERR-
> > > BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> > > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> > > Capabilities: [40] Power Management version 3
> > > Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> > PME(D0+,D1+,D2+,D3hot+,D3cold-)
> > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> > > Capabilities: [60] Express (v2) Root Port (Slot-), MSI 00
> > > DevCap: MaxPayload 256 bytes, PhantFunc 0
> > > ExtTag- RBE+
> > > DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> > Unsupported-
> > > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
> > > MaxPayload 128 bytes, MaxReadReq 512 bytes
> > > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
> > TransPend+
> > > LnkCap: Port #0, Speed 5GT/s, Width x2, ASPM not supported,
> > Exit Latency L0s unlimited, L1 unlimited
> > > ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
> > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
> > DLActive- BWMgmt- ABWMgmt-
> > > RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
> > CRSVisible+
> > > RootCap: CRSVisible+
> > > RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> > > DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR-,
> > OBFF Not Supported ARIFwd-
> > > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
> > OBFF Disabled ARIFwd-
> > > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> > > Transmit Margin: Normal Operating Range,
> > EnterModifiedCompliance- ComplianceSOS-
> > > Compliance De-emphasis: -6dB
> > > LnkSta2: Current De-emphasis Level: -3.5dB,
> > EqualizationComplete-, EqualizationPhase1-
> > > EqualizationPhase2-, EqualizationPhase3-,
> > LinkEqualizationRequest-
> > > Capabilities: [100 v1] Device Serial Number 00-00-00-00-00-00-00-00
> > > Capabilities: [10c v1] Virtual Channel
> > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> > > Arb: Fixed- WRR32- WRR64- WRR128-
> > > Ctrl: ArbSelect=Fixed
> > > Status: InProgress-
> > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> > > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
> > WRR256-
> > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> > > Status: NegoPending- InProgress-
> > > Capabilities: [128 v1] Vendor Specific Information: ID=1234 Rev=1
> > > Len=018 <?>
> > >
> > > 01:00.0 Network controller: Qualcomm Atheros AR93xx Wireless Network
> > Adapter (rev 01)
> > > Subsystem: Qualcomm Atheros Device 3112
> > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> > ParErr- Stepping- SERR- FastB2B- DisINTx-
> > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > <TAbort- <MAbort- >SERR- <PERR- INTx-
> > > Latency: 0, Cache Line Size: 128 bytes
> > > Interrupt: pin A routed to IRQ 224
> > > Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=128K]
> > > [virtual] Expansion ROM at e0020000 [disabled] [size=64K]
> > > Capabilities: [40] Power Management version 3
> > > Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA
> > PME(D0+,D1+,D2-,D3hot+,D3cold-)
> > > Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> > > Capabilities: [50] MSI: Enable- Count=1/4 Maskable+ 64bit+
> > > Address: 0000000000000000 Data: 0000
> > > Masking: 00000000 Pending: 00000000
> > > Capabilities: [70] Express (v2) Endpoint, MSI 00
> > > DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
> > L0s <1us, L1 <8us
> > > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> > SlotPowerLimit 0.000W
> > > DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
> > Unsupported-
> > > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
> > > MaxPayload 128 bytes, MaxReadReq 512 bytes
> > > DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
> > TransPend-
> > > LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit
> > Latency L0s <2us, L1 <64us
> > > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
> > > LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > > LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
> > DLActive- BWMgmt- ABWMgmt-
> > > DevCap2: Completion Timeout: Not Supported, TimeoutDis+,
> > LTR-, OBFF Not Supported
> > > DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-,
> > OBFF Disabled
> > > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
> > SpeedDis-
> > > Transmit Margin: Normal Operating Range,
> > EnterModifiedCompliance- ComplianceSOS-
> > > Compliance De-emphasis: -6dB
> > > LnkSta2: Current De-emphasis Level: -6dB,
> > EqualizationComplete-, EqualizationPhase1-
> > > EqualizationPhase2-, EqualizationPhase3-,
> > LinkEqualizationRequest-
> > > Capabilities: [100 v1] Advanced Error Reporting
> > > UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> > > UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
> > RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> > > UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
> > RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> > > CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> > NonFatalErr-
> > > CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
> > NonFatalErr+
> > > AERCap: First Error Pointer: 00, GenCap- CGenEn-
> > ChkCap- ChkEn-
> > > Capabilities: [140 v1] Virtual Channel
> > > Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> > > Arb: Fixed- WRR32- WRR64- WRR128-
> > > Ctrl: ArbSelect=Fixed
> > > Status: InProgress-
> > > VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> > > Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
> > WRR256-
> > > Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
> > > Status: NegoPending- InProgress-
> > > Capabilities: [300 v1] Device Serial Number 00-00-00-00-00-00-00-00
> > > Kernel driver in use: ath9k
> > >
> > > Here is the cat /proc/interrupts (after we do interface up):
> > >
> > > root@:~# ifconfig wlan0 up
> > > [ 1548.926601] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> > > root@Xilinx-ZCU102-2016_3:~# cat /proc/interrupts
> > > CPU0 CPU1 CPU2 CPU3
> > > 1: 0 0 0 0 GICv2 29 Edge arch_timer
> > > 2: 19873 20058 19089 17435 GICv2 30 Edge arch_timer
> > > 12: 0 0 0 0 GICv2 156 Level zynqmp-dma
> > > 13: 0 0 0 0 GICv2 157 Level zynqmp-dma
> > > 14: 0 0 0 0 GICv2 158 Level zynqmp-dma
> > > 15: 0 0 0 0 GICv2 159 Level zynqmp-dma
> > > 16: 0 0 0 0 GICv2 160 Level zynqmp-dma
> > > 17: 0 0 0 0 GICv2 161 Level zynqmp-dma
> > > 18: 0 0 0 0 GICv2 162 Level zynqmp-dma
> > > 19: 0 0 0 0 GICv2 163 Level zynqmp-dma
> > > 20: 0 0 0 0 GICv2 164 Level Mali_GP_MMU,
> Mali_GP,
> > Mali_PP0_MMU, Mali_PP0, Mali_PP1_MMU, Mali_PP1
> > > 30: 0 0 0 0 GICv2 95 Level eth0, eth0
> > > 206: 314 0 0 0 GICv2 49 Level cdns-i2c
> > > 207: 40 0 0 0 GICv2 50 Level cdns-i2c
> > > 209: 0 0 0 0 GICv2 150 Level nwl_pcie:misc
> > > 214: 12 0 0 0 GICv2 47 Level ff0f0000.spi
> > > 215: 0 0 0 0 GICv2 58 Level ffa60000.rtc
> > > 216: 0 0 0 0 GICv2 59 Level ffa60000.rtc
> > > 217: 0 0 0 0 GICv2 165 Level ahci-
> ceva[fd0c0000.ahci]
> > > 218: 61 0 0 0 GICv2 81 Level mmc0
> > > 219: 0 0 0 0 GICv2 187 Level arm-smmu global fault
> > > 220: 471 0 0 0 GICv2 53 Level xuartps
> > > 223: 0 0 0 0 GICv2 154 Level fd4c0000.dma
> > > 224: 3 0 0 0 dummy 1 Edge ath9k
> > > 225: 0 0 0 0 GICv2 97 Level xhci-hcd:usb1
> > >
> > > Regards,
> > > Bharat
> >
> > --
> > Kalle Valo
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of
> a message to majordomo@vger.kernel.org More majordomo info at
> http://vger.kernel.org/majordomo-info.html

\
 
 \ /
  Last update: 2016-12-09 07:55    [W:0.115 / U:0.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site