lkml.org 
[lkml]   [2016]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] stmmac: enable rx queues
From
Date
Hi Joao,

On 12/20/2016 03:59 PM, Joao Pinto wrote:
>
> Hi Séraphin,
>
> Às 2:52 PM de 12/20/2016, Seraphin BONNAFFE escreveu:
>> Hi Joao,
>>
>> Please see my in-line comments.
>>
>> Regards,
>> Séraphin
>> --
>> Seraphin BONNAFFE | Tel: +33244027061
>> STMicroelectronics | ADG | S/W Design
>>
>> On 12/20/2016 01:55 PM, Joao Pinto wrote:
>>> When the hardware is synthesized with multiple queues, all queues are
>>> disabled for default. This patch adds the rx queues configuration.
>>> This patch was successfully tested in a Synopsys QoS Reference design.
>>>
>>> Signed-off-by: Joao Pinto <jpinto@synopsys.com>
>>> ---
>>> drivers/net/ethernet/stmicro/stmmac/common.h | 2 ++
>>> drivers/net/ethernet/stmicro/stmmac/dwmac4.h | 4 ++++
>>> drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 11 +++++++++++
>>> drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 21 +++++++++++++++++++++
>>> 4 files changed, 38 insertions(+)
>>>
>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h
>>> b/drivers/net/ethernet/stmicro/stmmac/common.h
>>> index b13a144..61bab50 100644
>>> --- a/drivers/net/ethernet/stmicro/stmmac/common.h
>>> +++ b/drivers/net/ethernet/stmicro/stmmac/common.h
>>> @@ -454,6 +454,8 @@ struct stmmac_ops {
>>> void (*core_init)(struct mac_device_info *hw, int mtu);
>>> /* Enable and verify that the IPC module is supported */
>>> int (*rx_ipc)(struct mac_device_info *hw);
>>> + /* Enable RX Queues */
>>> + void (*rx_queue_enable)(struct mac_device_info *hw, u32 queue);
>>> /* Dump MAC registers */
>>> void (*dump_regs)(struct mac_device_info *hw);
>>> /* Handle extra events on specific interrupts hw dependent */
>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
>>> b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
>>> index 3e8d4fe..fd013bd 100644
>>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
>>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
>>> @@ -22,6 +22,7 @@
>>> #define GMAC_HASH_TAB_32_63 0x00000014
>>> #define GMAC_RX_FLOW_CTRL 0x00000090
>>> #define GMAC_QX_TX_FLOW_CTRL(x) (0x70 + x * 4)
>>> +#define GMAC_RXQ_CTRL0 0x000000a0
>>> #define GMAC_INT_STATUS 0x000000b0
>>> #define GMAC_INT_EN 0x000000b4
>>> #define GMAC_PCS_BASE 0x000000e0
>>> @@ -44,6 +45,9 @@
>>>
>>> #define GMAC_MAX_PERFECT_ADDRESSES 128
>>>
>>> +/* MAC RX Queue Enable*/
>>> +#define GMAC_RX_QUEUE_ENABLE(queue) BIT(queue * 2)
>>
>> According to the GMAC_RXQ0 register description from the dwc_ether_qos_databok,
>> I guess this will enable the queues in AV only.
>> What if we would like to enable them in DCB (10)b ?
>
> Correct, I am enabling AV only. What you are saying makes perfect sense. What
> about adding a variable to plat in order to configure the RX queue type?
> Example:
> plat->rx_queue_type = RX_QUEUE_DCB or plat->rx_queue_type = RX_QUEUE_AV
>

I am just not 100% sure about what does enabling the Queues in DCB implies,
and I think it needs something more to support the DCB feature as a whole in the driver, which is not supported yet.

On the other side, I observed that the queues should be enabled in AV by default.
Maybe providing this DCB option to plat could bring some confusion.
I would rather specify in the Macro name or in the comment above, that we are enabling the Queue in AV,
and eventually provide the same macro for enabling queues in DCB.

>
>>
>>
>>> +
>>> /* MAC Flow Control RX */
>>> #define GMAC_RX_FLOW_CTRL_RFE BIT(0)
>>>
>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
>>> b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
>>> index eaed7cb..7ec1887 100644
>>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
>>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
>>> @@ -59,6 +59,16 @@ static void dwmac4_core_init(struct mac_device_info *hw,
>>> int mtu)
>>> writel(value, ioaddr + GMAC_INT_EN);
>>> }
>>>
>>> +static void dwmac4_rx_queue_enable(struct mac_device_info *hw, u32 queue)
>>> +{
>>> + void __iomem *ioaddr = hw->pcsr;
>>> + u32 value = readl(ioaddr + GMAC_RXQ_CTRL0);
>>> +
>>> + value |= GMAC_RX_QUEUE_ENABLE(queue);
>>
>> What happen if for some reason the previous value of the register was 0xffff ?
>> The OR mask, by itself, won't clear the bits. AFAIU each queue is enabled with a
>> 2-bit value, and (11)b don't have the same effect as (01)b, does it ?
>>
>> I would suggest to clear the RXQ-enable bits before writing a new value.
>> Something like
>> value &= GMAC_RX_QUEUE_CLEAR(queue)
>> value |= GMAC_RX_QUEUE_ENABLE(queue);
>>
>> What do you think about that ?
>
> According to the databook, these values are always reset, but we can force it to
> clear as you suggest.
>
Yes, just in case. We may have another driver controlling the IP in a bootloader for example, and we don't know in which state it will let the controller.
...unless we have a IP reset at stmmac init (?). Anyway, it is more careful to control what we write to that register.

>>
>>> +
>>> + writel(value, ioaddr + GMAC_RXQ_CTRL0);
>>> +}
>>> +
>>> static void dwmac4_dump_regs(struct mac_device_info *hw)
>>> {
>>> void __iomem *ioaddr = hw->pcsr;
>>> @@ -392,6 +402,7 @@ static void dwmac4_debug(void __iomem *ioaddr, struct
>>> stmmac_extra_stats *x)
>>> static const struct stmmac_ops dwmac4_ops = {
>>> .core_init = dwmac4_core_init,
>>> .rx_ipc = dwmac4_rx_ipc_enable,
>>> + .rx_queue_enable = dwmac4_rx_queue_enable,
>>> .dump_regs = dwmac4_dump_regs,
>>> .host_irq_status = dwmac4_irq_status,
>>> .flow_ctrl = dwmac4_flow_ctrl,
>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>>> b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>>> index 3e40578..e30034d 100644
>>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
>>> @@ -1271,6 +1271,24 @@ static void free_dma_desc_resources(struct stmmac_priv
>>> *priv)
>>> }
>>>
>>> /**
>>> + * stmmac_mac_enable_rx_queues - Enable MAC rx queues
>>> + * @priv: driver private structure
>>> + * Description: It is used for enabling the rx queues in the MAC
>>> + */
>>> +static void stmmac_mac_enable_rx_queues(struct stmmac_priv *priv)
>>> +{
>>> + int rx_count = priv->dma_cap.number_rx_channel;
>>> + int queue = 0;
>>> +
>>> + /* If GMAC does not have multiqueues, then this is not necessary*/
>>> + if (rx_count == 1)
>>> + return;
>>> +
>>> + for (queue = 0; queue < rx_count; queue++)
>>> + priv->hw->mac->rx_queue_enable(priv->hw, queue);
>>
>>
>> Maybe it is worth checking if (priv->hw->mac->rx_queue_enable)
>> before actually calling this callback ?
>> I can see you have implemented it for dwmac4, but not for dwmac100 and dwmac100
>> In that case we may have a null pointer exception here.
>
> Yes, you are absolutely correct. Since I am using gmac4, I forgot that stmmac
> can use other types.
>

By the way, do you have any idea if this RxQ enabling is necessary for dwmac version before 4.00?


Regards,
Séraphin
>>
>>> +}
>>> +
>>> +/**
>>> * stmmac_dma_operation_mode - HW DMA operation mode
>>> * @priv: driver private structure
>>> * Description: it is used for configuring the DMA operation mode register in
>>> @@ -1691,6 +1709,9 @@ static int stmmac_hw_setup(struct net_device *dev, bool
>>> init_ptp)
>>> /* Initialize the MAC Core */
>>> priv->hw->mac->core_init(priv->hw, dev->mtu);
>>>
>>> + /* Initialize MAC RX Queues */
>>> + stmmac_mac_enable_rx_queues(priv);
>>> +
>>> ret = priv->hw->mac->rx_ipc(priv->hw);
>>> if (!ret) {
>>> netdev_warn(priv->dev, "RX IPC Checksum Offload disabled\n");
>>>
>
> Thanks.
>

\
 
 \ /
  Last update: 2016-12-20 16:32    [W:2.123 / U:0.508 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site