lkml.org 
[lkml]   [2016]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] ARM: dts: sun8i-q8-common: enable bluetooth on SDIO Wi-Fi
On Mon, Dec 19, 2016 at 10:24:44PM +0800, Chen-Yu Tsai wrote:
> On Mon, Dec 19, 2016 at 10:08 PM, Icenowy Zheng <icenowy@aosc.xyz> wrote:
> >
> >
> > 19.12.2016, 18:09, "Maxime Ripard" <maxime.ripard@free-electrons.com>:
> >> On Fri, Dec 16, 2016 at 10:40:00PM +0800, Icenowy Zheng wrote:
> >>> >> > > &r_pio {
> >>> >> > > wifi_pwrseq_pin_q8: wifi_pwrseq_pin@0 {
> >>> >> > > - pins = "PL6", "PL7", "PL11";
> >>> >> > > + pins = "PL6", "PL7", "PL8", "PL11";
> >>> >> > > function = "gpio_in";
> >>> >> > > bias-pull-up;
> >>> >> > > };
> >>> >> >
> >>> >> > There's several things wrong here. The first one is that you rely
> >>> >> > solely on the pinctrl state to maintain a reset line. This is very
> >>> >> > fragile (especially since the GPIO pinctrl state are likely to go away
> >>> >> > at some point), but it also means that if your driver wants to recover
> >>> >> > from that situation at some point, it won't work.
> >>> >> >
> >>> >> > The other one is that the bluetooth and wifi chips are two devices in
> >>> >> > linux, and you assign that pin to the wrong device (wifi).
> >>> >> >
> >>> >> > rfkill-gpio is made just for that, so please use it.
> >>> >>
> >>> >> The GPIO is not for the radio, but for the full Bluetooth part.
> >>> >
> >>> > I know.
> >>> >
> >>> >> If it's set to 0, then the bluetooth part will reset, and the
> >>> >> hciattach will fail.
> >>> >
> >>> > Both rfkill-gpio and rfkill-regulator will shutdown when called
> >>> > (either by poking the reset pin or shutting down the regulator), so
> >>> > that definitely seems like an expected behavior to put the device in
> >>> > reset.
> >>> >
> >>> >> The BSP uses this as a rfkill, and the result is that the bluetooth
> >>> >> on/off switch do not work properly.
> >>> >
> >>> > Then rfkill needs fixing, but working around it by hoping that the
> >>> > core will probe an entirely different device, and enforcing a default
> >>> > that the rest of the kernel might or might not change is both fragile
> >>> > and wrong.
> >>>
> >>> I think a rfkill-gpio here works just like the BSP rfkill...
> >>>
> >>> The real problem is that the Realtek UART bluetooth driver is a userspace
> >>> program (a modified hciattach), which is not capable of the GPIO reset...
> >>
> >> Can't you run rfkill before attaching? What is the problem exactly?
> >> It's not in reset for long enough?
> >>
> >> This seems more and more like an issue in the BT stack you're
> >> using. We might consider workarounds in the kernel, but they have to
> >> be correct.
> >
> > One more rfkill interface will be generated for hci0 after hciattach, which can
> > be safely toggled block and unblock.
> >
> > However, if the GPIO is toggled down, the hciattach program will die.
> >
> > The bluetooth stack I used is fd.o's BlueZ.
>
> I think the bigger issue is that the tty/serial subsystem does not have
> power sequencing support. Here we're trying to use rfkill to do that,
> but that doesn't seem to be what it was intended for. It might work with
> standalone USB bluetooth controllers that don't need any special setup,
> since the device will just appear and get registered. But it might not
> work so well with UART based adapters that need userspace fiddling with
> firmware and hciattach.

Then you can also have a look at the generic power sequence patches
that are floating around.

Maxime

--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2016-12-20 15:09    [W:0.035 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site