lkml.org 
[lkml]   [2016]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [RFC][PATCH 2/3] drm/bridge: adv7511: Add 200ms delay on power-on
Date
Hi Daniel,

On Wednesday 23 Nov 2016 08:55:37 Daniel Vetter wrote:
> On Tue, Nov 22, 2016 at 08:23:38PM +0200, Laurent Pinchart wrote:
> > On Tuesday 22 Nov 2016 10:07:53 John Stultz wrote:
> >> On Tue, Nov 22, 2016 at 9:38 AM, John Stultz wrote:
> >>> Interestingly, without the msleep added in this patch, removing the
> >>> wait_event_interruptible_timeout() method in adv7511_wait_for_edid()
> >>> and using the polling loop seems to make things just as reliable. So
> >>> maybe something is off with the irq handling here instead?
> >>
> >> Ahhhh.. So I think the trouble here is the that when we fail waiting
> >> for the irq, the backtrace is as follows:
> >>
> >> [ 8.318654] [<ffffff8008087c28>] dump_backtrace+0x0/0x1a0
> >> [ 8.318661] [<ffffff8008087ddc>] show_stack+0x14/0x20
> >> [ 8.318671] [<ffffff80084344f0>] dump_stack+0x90/0xb0
> >> [ 8.318680] [<ffffff8008534650>] adv7511_get_edid_block+0x2c8/0x320
> >> [ 8.318687] [<ffffff80085214a8>] drm_do_get_edid+0x78/0x280
> >> [ 8.318693] [<ffffff8008534728>] adv7511_get_modes+0x80/0xd8
> >> [ 8.318700] [<ffffff8008534794>]
> >> adv7511_connector_get_modes+0x14/0x20
> >> [ 8.318710] [<ffffff8008500a54>]
> >> drm_helper_probe_single_connector_modes+0x2bc/0x500
> >> [ 8.318718] [<ffffff800850e400>]
> >> drm_fb_helper_hotplug_event+0x130/0x188
> >> [ 8.318726] [<ffffff800850ee68>]
> >> drm_fbdev_cma_hotplug_event+0x10/0x20
> >> [ 8.318733] [<ffffff8008535718>]
> >> kirin_fbdev_output_poll_changed+0x20/0x58
> >> [ 8.318740] [<ffffff8008500cc0>]
> >> drm_kms_helper_hotplug_event+0x28/0x38
> >> [ 8.318748] [<ffffff80085010d8>] drm_helper_hpd_irq_event+0x138/0x180
> >> [ 8.318754] [<ffffff8008533850>] adv7511_irq_process+0x78/0xd8
> >> [ 8.318761] [<ffffff80085338c4>] adv7511_irq_handler+0x14/0x28
> >> [ 8.318769] [<ffffff8008100060>] irq_thread_fn+0x28/0x68
> >> [ 8.318775] [<ffffff8008100350>] irq_thread+0x128/0x1e8
> >> [ 8.318782] [<ffffff80080d2e68>] kthread+0xd0/0xe8
> >> [ 8.318788] [<ffffff8008082e80>] ret_from_fork+0x10/0x50
> >>
> >> So we're actually in irq handling the hotplug interrupt, which is why
> >> we never get the irq notification when the edid is read.
> >>
> >> I suspect we need to use a workqueue to do the hotplug handling out of
> >> irq.
> >
> > Lovely :-)
> >
> > Quoting the DRM documentation:
> >
> > /**
> > * drm_helper_hpd_irq_event - hotplug processing
> > * @dev: drm_device
> > *
> > * Drivers can use this helper function to run a detect cycle on all
> > connectors
> > * which have the DRM_CONNECTOR_POLL_HPD flag set in their &polled member.
> > All
> > * other connectors are ignored, which is useful to avoid reprobing fixed
> > * panels.
> > *
> > * This helper function is useful for drivers which can't or don't track
> > hotplug
> > * interrupts for each connector.
> > *
> > * Drivers which support hotplug interrupts for each connector
> > individually and
> > * which have a more fine-grained detect logic should bypass this code and
> > * directly call drm_kms_helper_hotplug_event() in case the connector
> > state
> > * changed.
> > *
> > * This function must be called from process context with no mode
> > * setting locks held.
> > *
> > * Note that a connector can be both polled and probed from the hotplug
> > handler,
> > * in case the hotplug interrupt is known to be unreliable.
> > */
> >
> > So it looks like we should use drm_kms_helper_hotplug_event() instead.
> >
> > /**
> > * drm_kms_helper_hotplug_event - fire off KMS hotplug events
> > * @dev: drm_device whose connector state changed
> > *
> > * This function fires off the uevent for userspace and also calls the
> > * output_poll_changed function, which is most commonly used to inform the
> > fbdev
> > * emulation code and allow it to update the fbcon output configuration.
> > *
> > * Drivers should call this from their hotplug handling code when a change
> > is
> > * detected. Note that this function does not do any output detection of
> > its
> > * own, like drm_helper_hpd_irq_event() does - this is assumed to be done
> > by the
> > * driver already.
> > *
> > * This function must be called from process context with no mode
> > * setting locks held.
> > */
> >
> > The function suffers from the same problem though, that it must be called
> > from process context.
> >
> > Daniel, why do we have an API the is clearly related to interrupt handling
> > but requires the caller to implement a workqueue ?
>
> Because in general you need that workqueue anyway, and up to now there was
> no driver ever who didn't have a work-queue already.

None of the bridge drivers in drivers/gpu/drm/bridge/ have workqueues. They
call the HPD helpers from a threaded interrupt handler though. Sleeping in
that context is fine, calling functions that might rely on interrupts from the
same device to signal completion (such as reading EDID through .get_modes())
isn't.

> Nesting workqueues
> within workqueues seemed beyond silly, hence why I removed them in:
>
> commit 69787f7da6b2adc4054357a661aaa1701a9ca76f
> Author: Daniel Vetter <daniel.vetter@ffwll.ch>
> Date: Tue Oct 23 18:23:34 2012 +0000
>
> drm: run the hpd irq event code directly
>
> I guess we could talk about re-introducing a work-item based version of
> drm_helper_hpd_irq_event. But for drm_kms_helper_hotplug_event I think it
> doesn't make sense - if you call that you've probably just done a pile of
> i2c transactions, and those can sleep. If you haven't done i2c
> transactions, then it's not an external panel, and why exactly are you
> handling hpd for them?

--
Regards,

Laurent Pinchart

\
 
 \ /
  Last update: 2016-11-25 01:24    [W:0.477 / U:0.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site