Messages in this thread | | | Subject | Re: [Intel-wired-lan] [PATCH v2] e1000e: free IRQ regardless of __E1000_DOWN | From | "Neftin, Sasha" <> | Date | Thu, 17 Nov 2016 15:31:21 +0200 |
| |
On 11/13/2016 10:34 AM, Neftin, Sasha wrote: > On 11/11/2016 12:35 AM, Baicar, Tyler wrote: >> Hello Sasha, >> >> On 11/9/2016 11:19 PM, Neftin, Sasha wrote: >>> On 11/9/2016 11:41 PM, Tyler Baicar wrote: >>>> Move IRQ free code so that it will happen regardless of the >>>> __E1000_DOWN bit. Currently the e1000e driver only releases its IRQ >>>> if the __E1000_DOWN bit is cleared. This is not sufficient because >>>> it is possible for __E1000_DOWN to be set without releasing the IRQ. >>>> In such a situation, we will hit a kernel bug later in e1000_remove >>>> because the IRQ still has action since it was never freed. A >>>> secondary bus reset can cause this case to happen. >>>> >>>> Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org> >>>> --- >>>> drivers/net/ethernet/intel/e1000e/netdev.c | 3 ++- >>>> 1 file changed, 2 insertions(+), 1 deletion(-) >>>> >>>> diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c >>>> b/drivers/net/ethernet/intel/e1000e/netdev.c >>>> index 7017281..36cfcb0 100644 >>>> --- a/drivers/net/ethernet/intel/e1000e/netdev.c >>>> +++ b/drivers/net/ethernet/intel/e1000e/netdev.c >>>> @@ -4679,12 +4679,13 @@ int e1000e_close(struct net_device *netdev) >>>> if (!test_bit(__E1000_DOWN, &adapter->state)) { >>>> e1000e_down(adapter, true); >>>> - e1000_free_irq(adapter); >>>> /* Link status message must follow this format */ >>>> pr_info("%s NIC Link is Down\n", adapter->netdev->name); >>>> } >>>> + e1000_free_irq(adapter); >>>> + >>>> napi_disable(&adapter->napi); >>>> e1000e_free_tx_resources(adapter->tx_ring); >>>> >>> I would like not recommend insert this change. This change related >>> driver state machine, we afraid from lot of synchronization problem and >>> issues. >>> We need keep e1000_free_irq in loop and check for 'test_bit' ready. >> >> What do you mean here? There is no loop. If __E1000_DOWN is set then we >> will never free the IRQ. >> >>> Another point, does before execute secondary bus reset your SW back up >>> pcie configuration space as properly? >> >> After a secondary bus reset, the link needs to recover and go back to a >> working state after 1 second. >> >> From the callstack, the issue is happening while removing the endpoint >> from the system, before applying the secondary bus reset. >> >> The order of events is >> 1. remove the drivers >> 2. cause a secondary bus reset >> 3. wait 1 second > Actually, this is too much, usually link up in less than 100ms.You can > check Data Link Layer indication. >> 4. recover the link >> >> callstack: >> free_msi_irqs+0x6c/0x1a8 >> pci_disable_msi+0xb0/0x148 >> e1000e_reset_interrupt_capability+0x60/0x78 >> e1000_remove+0xc8/0x180 >> pci_device_remove+0x48/0x118 >> __device_release_driver+0x80/0x108 >> device_release_driver+0x2c/0x40 >> pci_stop_bus_device+0xa0/0xb0 >> pci_stop_bus_device+0x3c/0xb0 >> pci_stop_root_bus+0x54/0x80 >> acpi_pci_root_remove+0x28/0x64 >> acpi_bus_trim+0x6c/0xa4 >> acpi_device_hotplug+0x19c/0x3f4 >> acpi_hotplug_work_fn+0x28/0x3c >> process_one_work+0x150/0x460 >> worker_thread+0x50/0x4b8 >> kthread+0xd4/0xe8 >> ret_from_fork+0x10/0x50 >> >> Thanks, >> Tyler >> > Hello Tyler, > Okay, we need consult more about this suggestion. > May I ask what is setup you run? Is there NIC or on board LAN? I would > like try reproduce this issue in our lab's too. > Also, is same issue observed with same scenario and others NIC's too? > Sasha > _______________________________________________ > Intel-wired-lan mailing list > Intel-wired-lan@lists.osuosl.org > http://lists.osuosl.org/mailman/listinfo/intel-wired-lan > Hello Tyler, I see some in consistent implementation of __*_close methods in our drivers. Do you have any igb NIC to check if same problem persist there? Thanks, Sasha
| |