lkml.org 
[lkml]   [2016]   [Nov]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2] mmc: sdhci-of-esdhc: fixup PRESENT_STATE read
From
Date
On 14/11/16 10:50, Michael Walle wrote:
> Am 2016-11-14 04:00, schrieb Y.B. Lu:
>>> -----Original Message-----
>>> From: Michael Walle [mailto:michael@walle.cc]
>>> Sent: Saturday, November 12, 2016 12:04 AM
>>> To: linux-kernel@vger.kernel.org
>>> Cc: linux-mmc@vger.kernel.org; Ulf Hansson; Adrian Hunter; yangbo lu;
>>> Michael Walle
>>> Subject: [PATCH v2] mmc: sdhci-of-esdhc: fixup PRESENT_STATE read
>>>
>>> Since commit 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy
>>> cards in __mmc_switch()") the ESDHC driver is broken:
>>> mmc0: Card stuck in programming state! __mmc_switch
>>> mmc0: error -110 whilst initialising MMC card
>>>
>>> Since this commit __mmc_switch() uses ->card_busy(), which is
>>> sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
>>> PRESENT_STATE register, specifically the DAT0 signal level bit. But the
>>> ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
>>> required to make the driver work again.
>>>
>>> Signed-off-by: Michael Walle <michael@walle.cc>
>>> Fixes: 87a18a6a5652 ("mmc: mmc: Use ->card_busy() to detect busy cards in
>>> __mmc_switch()")
>>> ---
>>> v2:
>>> - use lower bits of the original value (that was actually a typo)
>>> - add fixes tag
>>> - fix typo
>>>
>>> drivers/mmc/host/sdhci-of-esdhc.c | 12 ++++++++++++
>>> 1 file changed, 12 insertions(+)
>>>
>>> diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-
>>> of-esdhc.c
>>> index fb71c86..f9c84bb 100644
>>> --- a/drivers/mmc/host/sdhci-of-esdhc.c
>>> +++ b/drivers/mmc/host/sdhci-of-esdhc.c
>>> @@ -66,6 +66,18 @@ static u32 esdhc_readl_fixup(struct sdhci_host *host,
>>> return ret;
>>> }
>>> }
>>> + /*
>>> + * The DAT[3:0] line signal levels and the CMD line signal level is
>>> + * not compatible with standard SDHC register. Move the
>>> corresponding
>>> + * bits around.
>>> + */
>>> + if (spec_reg == SDHCI_PRESENT_STATE) {
>>> + ret = value & ~0xf8000000;
>>
>> [Lu Yangbo-B47093] I think the bits which should be cleaned before
>> following '|=' are 0x01f00000 not 0xf8000000, right?
>> :)
>
> Its neither 0x01f00000 nor 0xf8000000 :( I'll put the bits definition into
> the comment the next time, so everyone can review them. bit[31:24] are the
> line DAT[7:0] line signal level. bit[23] is command signal level. All other
> bits are the same as in the standard SDHC PRESENT_STATE register.
>
> I want to keep all but the upper 9 bits from the original value, therefore,
> this should be the correct mask:
> ret = value & ~0xff800000;

Why keep bits 22:20 ? Isn't it more logical to keep 19:0 (i.e. ret = value
& 0xfffff)

>
> -michael
>
>>
>>> + ret |= (value >> 4) & SDHCI_DATA_LVL_MASK;
>>> + ret |= (value << 1) & 0x01000000;
>>> + return ret;
>>> + }
>>> +
>>> ret = value;
>>> return ret;
>>> }
>>> --
>>> 2.1.4
>
>

\
 
 \ /
  Last update: 2016-11-14 10:44    [W:0.207 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site