lkml.org 
[lkml]   [2016]   [Oct]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4] media: Driver for Toshiba et8ek8 5MP sensor
Hi Pavel,

(Cc Laurent.)

On Sun, Oct 23, 2016 at 10:40:01PM +0200, Pavel Machek wrote:
> Hi!
>
> > Thanks, this answered half of my questions already. ;-)
> >
> > Do all the modes work for you currently btw.?
>
> Aha, went through my notes. This is what it does in 5MP mode, even on
> v4.9:
>
> pavel@n900:/my/fcam-dev$ ./camera.py
> ['-r']
> ['-l', '"et8ek8 3-003e":0 -> "video-bus-switch":1 [1]']
> ['-l', '"video-bus-switch":0 -> "OMAP3 ISP CCP2":0 [1]']
> ['-l', '"OMAP3 ISP CCP2":1 -> "OMAP3 ISP CCDC":0 [1]']
> ['-l', '"OMAP3 ISP CCDC":1 -> "OMAP3 ISP CCDC output":0 [1]']
> ['-V', '"et8ek8 3-003e":0 [SGRBG10 2592x1968]']
> ['-V', '"OMAP3 ISP CCP2":0 [SGRBG10 2592x1968]']
> ['-V', '"OMAP3 ISP CCP2":1 [SGRBG10 2592x1968]']
> ['-V', '"OMAP3 ISP CCDC":1 [SGRBG10 2592x1968]']
> ['-V', '"OMAP3 ISP CCDC":2 [SGRBG10 2592x1968]']
> Device /dev/video2 opened.
> Device `OMAP3 ISP CCDC output' on `media' is a video capture (without
> mplanes) device.
> Video format set: SGRBG10 (30314142) 2592x1968 (stride 5184) field
> none buffer size 10202112
> Video format: SGRBG10 (30314142) 2592x1968 (stride 5184) field none
> buffer size 10202112
> 4 buffers requested.
> length: 10202112 offset: 0 timestamp type/source: mono/EoF
> Buffer 0/0 mapped at address 0xb63a0000.
> length: 10202112 offset: 10203136 timestamp type/source: mono/EoF
> Buffer 1/0 mapped at address 0xb59e5000.
> length: 10202112 offset: 20406272 timestamp type/source: mono/EoF
> Buffer 2/0 mapped at address 0xb502a000.
> length: 10202112 offset: 30609408 timestamp type/source: mono/EoF
> Buffer 3/0 mapped at address 0xb466f000.
> 0 (0) [E] any 0 10202112 B 0.000000 2792.366987 0.001 fps ts mono/EoF
> Unable to queue buffer: Input/output error (5).
> Unable to requeue buffer: Input/output error (5).
> Unable to release buffers: Device or resource busy (16).
> pavel@n900:/my/fcam-dev$
>
> (gitlab.com fcam-dev branch good)
>
> Kernel will say
>
> [ 2689.598358] stream on success
> [ 2702.426635] Streamon
> [ 2702.426727] check_format checking px 808534338 808534338, h 984
> 984, w 1296 1296, bpline 2592 2592, size 2550528 2550528 field 1 1
> [ 2702.426818] configuring for 1296(2592)x984
> [ 2702.434722] stream on success
> [ 2792.276184] Streamon
> [ 2792.276306] check_format checking px 808534338 808534338, h 1968
> 1968, w 2592 2592, bpline 5184 5184, size 10202112 10202112 field 1 1
> [ 2792.276367] configuring for 2592(5184)x1968
> [ 2792.284240] stream on success
> [ 2792.368164] omap3isp 480bc000.isp: CCDC won't become idle!

This is Bad(tm).

It means that the driver waited for the CCDC to become idle to reprogram it,
but it didn't happen. This could be a problem in the number of lines
configured, or some polarity settings between the CCP2 receiver and the
CCDC. I suspect the latter, but I could be totally wrong here as well since
it was more than five years I worked on these things. :-I

> [ 2793.901550] omap3isp 480bc000.isp: Unable to stop OMAP3 ISP CCDC

And this is probably directly caused by the same problem. :-(

--
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@iki.fi XMPP: sailus@retiisi.org.uk

\
 
 \ /
  Last update: 2016-10-31 23:59    [W:0.184 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site