lkml.org 
[lkml]   [2016]   [Oct]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 6/5] KVM: x86: fix periodic lapic timer with hrtimers
2016-10-25 19:43 GMT+08:00 Radim Krčmář <rkrcmar@redhat.com>:
> 2016-10-25 07:39+0800, Wanpeng Li:
>> 2016-10-24 23:27 GMT+08:00 Radim Krčmář <rkrcmar@redhat.com>:
>>> 2016-10-24 17:09+0200, Paolo Bonzini:
>>>> On 24/10/2016 17:03, Radim Krčmář wrote:
>>> [...]
>>>>
>>>> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
>>>>
>>>> Go ahead, squash it into 5/5 and commit to kvm/queue. :)
>>>
>>> Did that, thanks.
>>>
>>> Wanpeng, the code is now under your name so please check it and/or
>>> complain.
>>
>> This patch 6/5 incurred regressions.
>>
>> - The latency of the periodic mode which is emulated by VMX preemption
>> is almost the same as periodic mode which is emulated by hrtimer.
>
> Hm, what numbers are you getting?

The two fixes look good to me. However, the codes which you remove in
kvm_lapic_switch_to_hv_timer() results in different numbers.

w/o remove hlt average latency = 2398462
w/ remove hlt average latency = 2403845

>
> When I ran the test with the original series, then it actually had worse

Did you test this by running my kvm-unit-tests/apic_timer_latency.flat?

> results with the VMX preemption than it did with the hrimer:
>
> hlt average latency = 1464151
> pause average latency = 1467605
>
> htl tests the hrtimer, pause tests the VMX preemption. I just replaced
> "hlt" with "pause" in the assembly loop.
>
> The worse result was because the VMX preemption period was computed
> incorrectly -- it was being added to now(). Some time passes between
> the expiration and reading of now(), so this time was extending the
> period while it shouldn't have.
>
> If I run the test with [6/5], it gets sane numbers:
>
> hlt average latency = 1465107
> pause average latency = 1465093
>
> The numbers are sane bacause the test is not computing latency (= how
> long after the timer should have fired have we received the interrupt)
> -- it is computing the duration of the period in cycles, which is much
> better right now.

Agreed.

>
>> - The oneshot mode test of kvm-unit-tests/apic_timer_latency.flat almost fail.
>
> Oops, silly mistake -- apic_timer_expired() was in the 'else' branch in
> [5/5] and I didn't invert the condition after moving it.
>
> diff --git a/arch/x86/kvm/lapic.c b/arch/x86/kvm/lapic.c
> index 6244988418be..d7e74c8ec8ca 100644
> --- a/arch/x86/kvm/lapic.c
> +++ b/arch/x86/kvm/lapic.c
> @@ -1354,8 +1354,8 @@ static void start_sw_period(struct kvm_lapic *apic)
> return;
>
> if (apic_lvtt_oneshot(apic) &&
> - ktime_after(apic->lapic_timer.target_expiration,
> - apic->lapic_timer.timer.base->get_time())) {
> + !ktime_after(apic->lapic_timer.target_expiration,
> + apic->lapic_timer.timer.base->get_time())) {
> apic_timer_expired(apic);
> return;
> }
>

It works.

> Paolo, can you squash that?
>
>> Btw, hope you can also apply the testcase for kvm-unit-tests. :)
>
> I will have some comments, because it would be nicer if it measured the
> latency ... expected_expiration is not computed correctly.

It measured the latency from guest programs the clock event device to
interrupt injected to guest after timer fire.

Regards,
Wanpeng Li

\
 
 \ /
  Last update: 2016-10-26 08:02    [W:0.130 / U:1.468 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site