lkml.org 
[lkml]   [2016]   [Oct]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 05/11] docs: Get rid of the "basic profiling" guide
Date
The document has not been touched in over 11 years and doesn't reflect how
profiling is done in the perf era.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
---
Documentation/admin-guide/basic-profiling.rst | 68 ---------------------------
Documentation/admin-guide/index.rst | 1 -
2 files changed, 69 deletions(-)
delete mode 100644 Documentation/admin-guide/basic-profiling.rst

diff --git a/Documentation/admin-guide/basic-profiling.rst b/Documentation/admin-guide/basic-profiling.rst
deleted file mode 100644
index 72babc71b771..000000000000
--- a/Documentation/admin-guide/basic-profiling.rst
+++ /dev/null
@@ -1,68 +0,0 @@
-Basic kernel profiling
-======================
-
-
-These instructions are deliberately very basic. If you want something clever,
-go read the real docs ;-)
-
-Please don't add more stuff, but feel free to
-correct my mistakes ;-) (mbligh@aracnet.com)
-
-Thanks to John Levon, Dave Hansen, et al. for help writing this.
-
-``<test>`` is the thing you're trying to measure.
-Make sure you have the correct ``System.map`` / ``vmlinux`` referenced!
-
-It is probably easiest to use ``make install`` for linux and hack
-``/sbin/installkernel`` to copy ``vmlinux`` to ``/boot``, in addition to
-``vmlinuz``, ``config``, ``System.map``, which are usually installed by default.
-
-Readprofile
------------
-
-A recent ``readprofile`` command is needed for 2.6, such as found in util-linux
-2.12a, which can be downloaded from:
-
- http://www.kernel.org/pub/linux/utils/util-linux/
-
-Most distributions will ship it already.
-
-Add ``profile=2`` to the kernel command line.
-
-Some ``readprofile`` commands::
-
- clear readprofile -r
- <test>
- dump output readprofile -m /boot/System.map > captured_profile
-
-Oprofile
---------
-
-Get the source (see Changes for required version) from
-http://oprofile.sourceforge.net/ and add ``idle=poll`` to the kernel command
-line.
-
-Configure with ``CONFIG_PROFILING=y`` and ``CONFIG_OPROFILE=y`` & reboot on new kernel::
-
- ./configure --with-kernel-support
- make install
-
-For superior results, be sure to enable the local APIC. If opreport sees
-a 0Hz CPU, APIC was not on. Be aware that idle=poll may mean a performance
-penalty.
-
-One time setup::
-
- opcontrol --setup --vmlinux=/boot/vmlinux
-
-Some ``opcontrol`` commands::
-
- clear opcontrol --reset
- start opcontrol --start
- <test>
- stop opcontrol --stop
- dump output opreport > output_file
-
-To only report on the kernel, run ``opreport -l /boot/vmlinux > output_file``
-
-A reset is needed to clear old statistics, which survive a reboot.
diff --git a/Documentation/admin-guide/index.rst b/Documentation/admin-guide/index.rst
index d737ae71efc6..2872c0c70ea4 100644
--- a/Documentation/admin-guide/index.rst
+++ b/Documentation/admin-guide/index.rst
@@ -58,4 +58,3 @@ configure specific aspects of kernel behavior to your liking.
binfmt-misc
mono
java
- basic-profiling
--
2.7.4
\
 
 \ /
  Last update: 2016-10-27 01:23    [W:0.105 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site