lkml.org 
[lkml]   [2016]   [Oct]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 01/10] Documentation: dt-bindings: Document STM32 ADC DT bindings
Date
This patch adds documentation of device tree bindings for the STM32 ADC.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
---
.../devicetree/bindings/iio/adc/st,stm32-adc.txt | 78 ++++++++++++++++++++++
1 file changed, 78 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt

diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
new file mode 100644
index 0000000..a9a8b3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
@@ -0,0 +1,78 @@
+STMicroelectronics STM32 ADC device driver
+
+STM32 ADC is a successive approximation analog-to-digital converter.
+It has several multiplexed input channels. Conversions can be performed
+in single, continuous, scan or discontinuous mode. Result of the ADC is
+stored in a left-aligned or right-aligned 32-bit data register.
+Conversions can be launched in software or using hardware triggers.
+
+The analog watchdog feature allows the application to detect if the input
+voltage goes beyond the user-defined, higher or lower thresholds.
+
+Each STM32 ADC block can have up to 3 ADC instances.
+
+Each instance supports two contexts to manage conversions, each one has its
+own configurable sequence and trigger:
+- regular conversion can be done in sequence, running in background
+- injected conversions have higher priority, and so have the ability to
+ interrupt regular conversion sequence (either triggered in SW or HW).
+ Regular sequence is resumed, in case it has been interrupted.
+
+Required properties:
+- compatible: Should be "st,stm32f4-adc".
+- reg: Offset and length of the ADC block register set.
+- interrupts: Must contain the interrupt for ADC.
+- clocks: Clock for the analog circuitry (common to all ADCs).
+- clock-names: Must be "adc".
+- vref-supply: Phandle to the vref input analog reference voltage.
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- A pinctrl state named "default" for each ADC channel may be defined to set
+ inX ADC pins in mode of operation for analog input on external pin.
+- gpios: Array of gpios that may be configured as EXTi trigger sources.
+
+Example:
+ adc: adc@40012000 {
+ compatible = "st,stm32f4-adc";
+ reg = <0x40012000 0x400>;
+ interrupts = <18>;
+ clocks = <&rcc 0 168>;
+ clock-names = "adc";
+ vref-supply = <&reg_vref>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&adc3_in8_pin>;
+ gpios = <&gpioa 11 0>,
+ <&gpioa 15 0>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc1: adc1-master@0 {
+ #io-channel-cells = <1>;
+ reg = <0x0>;
+ clocks = <&rcc 0 168>;
+ st,adc-channels = <8>;
+ };
+ ...
+ other adc child nodes follow...
+ };
+
+Contents of a stm32 adc child node:
+-----------------------------------
+An ADC block node should contain at least one subnode, representing an
+ADC instance available on the machine.
+
+Required properties:
+- reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200).
+- st,adc-channels: List of single-ended channels muxed for this ADC.
+- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in
+ Documentation/devicetree/bindings/iio/iio-bindings.txt
+
+Optional properties:
+- clocks: Input clock private to this ADC instance.
+- st,injected: Use injected conversion sequence on an ADC, rather than regular.
+- dmas: Phandle to dma channel for this ADC instance, only for regular
+ conversions. See ../../dma/dma.txt for details.
+- dma-names: Must be "rx" when dmas property is being used.
--
1.9.1
\
 
 \ /
  Last update: 2016-10-25 18:29    [W:0.128 / U:12.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site