lkml.org 
[lkml]   [2016]   [Jan]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] Documentation: atmel-at91: add DT bindings for fast startup
On Thu, Jan 28, 2016 at 06:19:16PM +0800, Wenyou Yang wrote:
> Add DT bindings to configurate the PMC_FSMR and PMC_FSPR registers
> to trigger a fast restart signal to PMC.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
> ---
>
> .../devicetree/bindings/arm/atmel-pmc.txt | 74 ++++++++++++++++++++
> 1 file changed, 74 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
> index 795cc78..8d45ff9f 100644
> --- a/Documentation/devicetree/bindings/arm/atmel-pmc.txt
> +++ b/Documentation/devicetree/bindings/arm/atmel-pmc.txt
> @@ -12,3 +12,77 @@ Examples:
> compatible = "atmel,at91rm9200-pmc";
> reg = <0xfffffc00 0x100>;
> };
> +
> +PMC Fast Startup Signals
> +
> +The PMC Fast Start Signals are used as the wake up source to trigger the PMC
> +to wake up the system from the ULP1 mode.
> +
> +required properties:
> +- compatible: Should be "atmel,sama5d2-pmc-fast-startup".

Why the compatible? Does this correspond to some h/w block rather than
features of the PMC? If it is simply because you want to have a separate
driver, that is not a good reason.

> +
> +optional properties:
> +- atmel,fast-startup-wake-up: boolean to enable the WKUP pin to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-secumod: boolean to enable the Security Mode to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu0: boolean to enable the PIOBU0 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu1: boolean to enable the PIOBU1 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu2: boolean to enable the PIOBU2 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu3: boolean to enable the PIOBU3 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu4: boolean to enable the PIOBU4 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu5: boolean to enable the PIOBU5 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu6: boolean to enable the PIOBU6 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-piobu7: boolean to enable the PIOBU7 Input to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-gmac-wol: boolean to enable the GMAC Wake-up On LAN
> + to trigger a fast restart signal to the PMC.
> +- atmel,fast-startup-rtc-alarm: boolean to enable the RTC Alarm to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-usb-resume: boolean to enable the USB Resume to trigger
> + a fast restart signal to the PMC.
> +- atmel,fast-startup-sdmmc-cd: boolean to enable the SDMMC Card Detect
> + to trigger a fast restart signal to the PMC.
> +- atmel,fast-startup-rxlp-match: boolean to enable the Backuo UART Receive
> + Match Condition to trigger a fast restart signal to the PMC.
> +- atmel,fast-startup-acc-comparison: boolean to enable the Analog Comparator
> + Controller (ACC) Comparison to to trigger a fast restart signal to the PMC.
> +
> +- atmel,fast-startup-wkup-pin-high: boolean to indicate if the WKUP Pin is
> + in the high level to trigger fast restart signal, otherwise low level.

Perhaps just make the above bool properties take a value to indicate
high or low triggered.

> +- atmel,fast-startup-piobu0-high: boolean to indicate if the PIOBU0 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.
> +- atmel,fast-startup-piobu1-high: boolean to indicate if the PIOBU1 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.
> +- atmel,fast-startup-piobu2-high: boolean to indicate if the PIOBU2 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.
> +- atmel,fast-startup-piobu3-high: boolean to indicate if the PIOBU3 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.
> +- atmel,fast-startup-piobu4-high: boolean to indicate if the PIOBU4 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.
> +- atmel,fast-startup-piobu5-high: boolean to indicate if the PIOBU5 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.
> +- atmel,fast-startup-piobu6-high: boolean to indicate if the PIOBU6 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.
> +- atmel,fast-startup-piobu7-high: boolean to indicate if the PIOBU7 Pin is
> + in the high level to trigger fast restart signal, otherwise low level.

This would be a long list in the DT if you set all these properties.
Perhaps this should all be expressed in a more compact form.

> +
> +Example:
> +
> + pmc: pmc@f0014000 {
> + compatible = "atmel,sama5d2-pmc";
> + reg = <0xf0014000 0x160>;
> +
> + pmc_fast_restart {
> + compatible = "atmel,sama5d2-pmc-fast-startup";
> + atmel,fast-startup-wake-up;
> + atmel,fast-startup-rtc-alarm;
> + };
> + };
> --
> 1.7.9.5
>

\
 
 \ /
  Last update: 2016-01-29 17:41    [W:0.460 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site