lkml.org 
[lkml]   [2016]   [Jan]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 1/3] MIPS: R6: Use lightweight SYNC instruction in smp_* memory barriers
On Wed, 27 Jan 2016, Joshua Kinard wrote:

> On 06/05/2015 09:10, Ralf Baechle wrote:
> >
> > Maciej,
> >
> > do you have an R4000 / R4600 / R5000 / R7000 / SiByte system at hand to
> > test this? I think we don't need to test that SYNC actually works as
> > intended but the simpler test that SYNC <stype != 0> is not causing a
> > illegal instruction exception is sufficient, that is if something like
> >
> > int main(int argc, charg *argv[])
> > {
> > asm(" .set mips2 \n"
> > " sync 0x10 \n"
> > " sync 0x13 \n"
> > " sync 0x04 \n"
> > " .set mips 0 \n");
> >
> > return 0;
> > }
> >
> > doesn't crash we should be ok.

No anomalies observed with these processors:

CPU0 revision is: 00000440 (R4400SC)
CPU0 revision is: 01040102 (SiByte SB1)

> I tried just compiling this on my SGI O2, which has an RM7000 CPU, and it is
> refusing to even compile (after fixing typos):
>
> # gcc -O2 -pipe sync_test.c -o sync_test
> {standard input}: Assembler messages:
> {standard input}:19: Error: invalid operands `sync 0x10'
> {standard input}:20: Error: invalid operands `sync 0x13'
> {standard input}:21: Error: invalid operands `sync 0x04'

Yeah, there is another typo there: you need to use `.set mips32' or
suchlike rather than `.set mips2' to be able to specify an operand. That
probably counts as a bug in binutils, as -- according to what I have
observed in the other thread -- the `stype' field has been defined at
least since the MIPS IV ISA.

> And the program compiles successfully and executes with no noticeable oddities
> or errors. Nothing in dmesg, no crashes, booms, or disappearance of small

You did disable SYNC emulation in the kernel though with a change like
below, did you?

> kittens. I did a quick disassembly to make sure all three got emitted:
>
> 004005e0 <main>:
> 4005e0: 27bdfff8 addiu sp,sp,-8
> 4005e4: afbe0004 sw s8,4(sp)
> 4005e8: 03a0f021 move s8,sp
> 4005ec: afc40008 sw a0,8(s8)
> 4005f0: afc5000c sw a1,12(s8)
> > 4005f4: 0000040f sync.p
> > 4005f8: 0000050f 0x50f
> > 4005fc: 0000010f 0x10f
> 400600: 00001021 move v0,zero

You could have used the -m switch to override the architecture embedded
with the ELF file, to have the instructions disassembled correctly, e.g.:

$ objdump -m mips:isa64 -d sync
[...]
00000001200008f0 <main>:
1200008f0: 0000040f sync 0x10
1200008f4: 000004cf sync 0x13
1200008f8: 0000010f sync 0x4
1200008fc: 03e00008 jr ra
120000900: 0000102d move v0,zero
...
[...]

What's interesting to note is that rev. 2.60 of the architecture did
actually change the semantics of plain SYNC (aka SYNC 0) from an ordering
barrier to a completion barrier. Previous architectural requirements for
plain SYNC were equivalent to rev. 2.60's SYNC_MB, and to implement a
completion barrier a dummy load had to follow.

Some implementers of the old plain SYNC did actually make it a completion
rather than ordering barrier and people even argued this was an
architectural requirement, as I recall from discussions in early 2000s.
On the other hand the implementations affected were UP-only processors
where about the only use for SYNC was to drain any write buffers of data
intended for MMIO accesses and such an implementation did conform even if
it was too heavyweight for architectural requirements. So I think it was
a reasonable implementation decision, saving 1-2 instructions where a
completion barrier was required. The only downside of this decision was
some programmers assumed such semantics was universally guaranteed, while
indeed it was not (before rev. 2.60).

Overall where backwards compatibility is required it looks to me like we
need to keep the implementation of any completion barriers (e.g. `iob') as
a SYNC followed by a dummy load.

Maciej

linux-mips-no-sync.diff
Index: linux/arch/mips/kernel/traps.c
===================================================================
--- linux.orig/arch/mips/kernel/traps.c
+++ linux/arch/mips/kernel/traps.c
@@ -672,6 +672,7 @@ static int simulate_rdhwr_mm(struct pt_r
return -1;
}

+#if 0
static int simulate_sync(struct pt_regs *regs, unsigned int opcode)
{
if ((opcode & OPCODE) == SPEC0 && (opcode & FUNC) == SYNC) {
@@ -682,6 +683,7 @@ static int simulate_sync(struct pt_regs

return -1; /* Must be something else ... */
}
+#endif

asmlinkage void do_ov(struct pt_regs *regs)
{
@@ -1117,8 +1119,10 @@ asmlinkage void do_ri(struct pt_regs *re
if (status < 0)
status = simulate_rdhwr_normal(regs, opcode);

+#if 0
if (status < 0)
status = simulate_sync(regs, opcode);
+#endif

if (status < 0)
status = simulate_fp(regs, opcode, old_epc, old31);
\
 
 \ /
  Last update: 2016-01-29 15:21    [W:0.079 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site