lkml.org 
[lkml]   [2016]   [Jan]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] serial: imx: fix dcd interrupt firing during probe
Hi Marcel,

[also added Lucas]

On 2015-12-30 19:12, Marcel Ziswiler wrote:
> Continuing on the Apalis iMX6 mainlining work started by Petr Štetiar I
> noticed that it only boots when rebooting from NXP's downstream 3.14.28
> kernel or mainline otherwise (e.g. when cold booted) I did not get any
> serial debug output at all. Enabling earlyprintk I got the following:
>
> [ 1.136806] INFO: trying to register non-static key.
> [ 1.136871] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25,
> base_baud = 5000000) is a IMX
> [ 1.150651] the code is fine but needs lockdep annotation.
> [ 1.150653] turning off the locking correctness validator.
> [ 1.150664] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.0-rc6-
> next-20151223-00002-g6008f30-dirty #27
> [ 1.150668] Hardware name: Freescale i.MX6 Quad/DualLite (Device
> Tree)
> [ 1.150675] Backtrace:
> [ 1.150701] [<c010c45c>] (dump_backtrace) from [<c010c654>]
> (show_stack+0x18/0x1c)
> [ 1.150722] r7:00000000 r6:c0d20848 r5:00000000 r4:00000000
> [ 1.150739] [<c010c63c>] (show_stack) from [<c03dadcc>]
> (dump_stack+0x8c/0xa4)
> [ 1.150760] [<c03dad40>] (dump_stack) from [<c016b60c>]
> (__lock_acquire+0x1d88/0x1eb4)
> [ 1.150774] r7:00000000 r6:c0d063f8 r5:c155f834 r4:e503bc20
> [ 1.150785] [<c0169884>] (__lock_acquire) from [<c016bf54>]
> (lock_acquire+0x74/0x94)
> [ 1.150803] r10:c0d6eb5e r9:e597b300 r8:00000019 r7:00000001
> r6:00000001 r5:60000193
> [ 1.150808] r4:00000000
> [ 1.150821] [<c016bee0>] (lock_acquire) from [<c08d49d4>]
> (_raw_spin_lock_irqsave+0x40/0x54)
> [ 1.150834] r7:000052c8 r6:c0481470 r5:40000193 r4:e503bc10
> [ 1.150852] [<c08d4994>] (_raw_spin_lock_irqsave) from [<c0481470>]
> (imx_rxint+0x20/0x2a4)
> [ 1.150862] r6:00000000 r5:000052d0 r4:e503bc10
> [ 1.150874] [<c0481450>] (imx_rxint) from [<c0482540>]
> (imx_int+0x170/0x1f4)
>
> Debugging a little further I noticed this actually happening after
> calling devm_request_irq() during serial_imx_probe() even before
> uart_add_one_port() did initialise the spin_lock acquired in
> imx_rxint(). Turns out the data carrier detect interrupt fired
> immediately upon requesting interrupts. This patch fixes this by
> explicitly disabling data carrier detect before requesting interrupts.

I actually hit a very similar issue on the Colibri iMX6 and hence looked
into this too. In our downstream tree, I fixed it in imx_startup, which
is probably the wrong place actually...

>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
>
> ---
>
> drivers/tty/serial/imx.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
> index 9362f54c..b1588f9 100644
> --- a/drivers/tty/serial/imx.c
> +++ b/drivers/tty/serial/imx.c
> @@ -2032,6 +2032,11 @@ static int serial_imx_probe(struct platform_device *pdev)
> UCR1_TXMPTYEN | UCR1_RTSDEN);
> writel_relaxed(reg, sport->port.membase + UCR1);
>
> + /* Disable data carrier detect before requesting interrupts */
> + reg = readl_relaxed(sport->port.membase + UCR3);
> + reg &= ~(UCR3_DCD);
> + writel_relaxed(reg, sport->port.membase + UCR3);
> +

Note that UCR3_DCD has a different meaning in DCE mode. As a DCE, the
bit should be kept 1 (we assume that the carrier is detected by
default...)

The dte_mode bit should be initialized at that point, hence just making
that code conditional should account for that.

What I also noticed is that the RI signal suffers the very same issue.
We do not use the signal on our Colibri board, but we should disable
that interrupt too.

--
Stefan

> clk_disable_unprepare(sport->clk_ipg);
>
> /*

\
 
 \ /
  Last update: 2016-01-25 19:41    [W:0.037 / U:1.712 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site