lkml.org 
[lkml]   [2015]   [Sep]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 7/7] tty: serial: msm: Remove 115.2 Kbps maximum baud rate limitation
Date
UART controller is capable to perform transfers up to 4 Mbps.
Remove artificial 115.2 Kbps limitation.

Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
---
drivers/tty/serial/msm_serial.c | 20 +++++++++++++++++---
1 file changed, 17 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 3f975392ebc0..223514979685 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -880,6 +880,7 @@ msm_find_best_baud(struct uart_port *port, unsigned int baud)
{ 3, 0xdd, 8 },
{ 2, 0xee, 16 },
{ 1, 0xff, 31 },
+ { 0, 0xff, 31 },
};

divisor = uart_get_divisor(port, baud);
@@ -891,16 +892,29 @@ msm_find_best_baud(struct uart_port *port, unsigned int baud)
return entry; /* Default to smallest divider */
}

-static int msm_set_baud_rate(struct uart_port *port, unsigned int baud)
+static int msm_set_baud_rate(struct uart_port *port, unsigned int baud,
+ unsigned long *saved_flags)
{
unsigned int rxstale, watermark, mask;
struct msm_port *msm_port = UART_TO_MSM(port);
const struct msm_baud_map *entry;
+ unsigned long flags;

entry = msm_find_best_baud(port, baud);

msm_write(port, entry->code, UART_CSR);

+ if (baud > 460800)
+ port->uartclk = baud * 16;
+
+ flags = *saved_flags;
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ clk_set_rate(msm_port->clk, port->uartclk);
+
+ spin_lock_irqsave(&port->lock, flags);
+ *saved_flags = flags;
+
/* RX stale watermark */
rxstale = entry->rxstale;
watermark = UART_IPR_STALE_LSB & rxstale;
@@ -1024,8 +1038,8 @@ static void msm_set_termios(struct uart_port *port, struct ktermios *termios,
msm_stop_dma(port, dma);

/* calculate and set baud rate */
- baud = uart_get_baud_rate(port, termios, old, 300, 115200);
- baud = msm_set_baud_rate(port, baud);
+ baud = uart_get_baud_rate(port, termios, old, 300, 4000000);
+ baud = msm_set_baud_rate(port, baud, &flags);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);

--
1.9.1


\
 
 \ /
  Last update: 2015-09-12 15:21    [W:0.059 / U:11.996 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site