lkml.org 
[lkml]   [2015]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/1] ARM: dts: sun7i: Enable axp209 driver on olinuxino lime2
Hi Oliver,

On Wed, Sep 09, 2015 at 03:26:44PM +0200, Olliver Schinagl wrote:
> The Olimex OLinuXino Lime2 uses the same AXP209 as was recently
> introduced this driver for its power regulation.
>
> Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
> ---
> arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 87 +++++++++----------------
> 1 file changed, 31 insertions(+), 56 deletions(-)
>
> diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
> index d5c796c..dd90a1d 100644
> --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
> @@ -71,14 +71,6 @@
> default-state = "on";
> };
> };
> -
> - reg_axp_ipsout: axp_ipsout {
> - compatible = "regulator-fixed";
> - regulator-name = "axp-ipsout";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - regulator-always-on;
> - };

Why are you removing that regulator?

> };
>
> &ahci {
> @@ -86,6 +78,10 @@
> status = "okay";
> };
>
> +&cpu0 {
> + cpu-supply = <&reg_dcdc2>;
> +};
> +
> &ehci0 {
> status = "okay";
> };
> @@ -112,57 +108,9 @@
> status = "okay";
>
> axp209: pmic@34 {
> - compatible = "x-powers,axp209";
> reg = <0x34>;
> interrupt-parent = <&nmi_intc>;
> interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> -
> - interrupt-controller;
> - #interrupt-cells = <1>;
> -
> - acin-supply = <&reg_axp_ipsout>;
> - vin2-supply = <&reg_axp_ipsout>;
> - vin3-supply = <&reg_axp_ipsout>;
> - ldo24in-supply = <&reg_axp_ipsout>;
> - ldo3in-supply = <&reg_axp_ipsout>;

And these supplies?

> - regulators {
> - vdd_rtc: ldo1 {
> - regulator-min-microvolt = <1300000>;
> - regulator-max-microvolt = <1300000>;
> - regulator-always-on;
> - };
> -
> - avcc: ldo2 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - vcc_csi0: ldo3 {
> - regulator-min-microvolt = <700000>;
> - regulator-max-microvolt = <3500000>;
> - regulator-always-on;
> - };
> -
> - vcc_csi1: ldo4 {
> - regulator-min-microvolt = <1250000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - vdd_cpu: dcdc2 {
> - regulator-min-microvolt = <700000>;
> - regulator-max-microvolt = <2275000>;
> - regulator-always-on;
> - };
> -
> - vdd_int: dcdc3 {
> - regulator-min-microvolt = <700000>;
> - regulator-max-microvolt = <3500000>;
> - regulator-always-on;
> - };
> - };
> };
> };
>
> @@ -243,6 +191,33 @@
> status = "okay";
> };
>
> +#include "axp209.dtsi"
> +
> +&reg_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1450000>;

This is outside of the operating voltages of the CPU.

> + regulator-name = "vdd-cpu";
> +};
> +
> +&reg_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-int-dll";
> +};
> +
> +&reg_ldo1 {
> + regulator-name = "vdd-rtc";
> +};
> +
> +&reg_ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "avcc";

You're changing the boundaries, why?

> +};
> +
> &reg_usb0_vbus {
> pinctrl-0 = <&usb0_vbus_pin_lime2>;
> gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>;
> --
> 2.1.4

Thanks!
Maxime

--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2015-09-10 20:21    [W:0.112 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site