lkml.org 
[lkml]   [2015]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCHv2 2/3] devicetree: Add new ANX7814 SlimPort transmitter binding.
Date
Hi Enric,

On Thursday 10 September 2015 16:11:03 Enric Balletbo Serra wrote:
> 2015-09-09 2:40 GMT+02:00 Rob Herring <robh@kernel.org>:
> > On 09/08/2015 02:25 AM, Enric Balletbo i Serra wrote:
> >> The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
> >> designed for portable devices.
> >>
> >> You can add support to your board with current binding.
> >>
> >> Example:
> >> anx7814: anx7814@38 {
> >> compatible = "analogix,anx7814";
> >> reg = <0x38>;
> >> pd-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
> >> reset-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
> >> };
> >>
> >> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> >> ---
> >>
> >> .../devicetree/bindings/video/anx7814.txt | 22 ++++++++++++++++
> >> 1 file changed, 22 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/video/anx7814.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/video/anx7814.txt
> >> b/Documentation/devicetree/bindings/video/anx7814.txt new file mode
> >> 100644
> >> index 0000000..a8cc746
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/video/anx7814.txt
> >> @@ -0,0 +1,22 @@
> >> +Analogix ANX7814 SlimPort (Full-HD Transmitter)
> >> +-----------------------------------------------
> >> +
> >> +The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
> >> +designed for portable devices.
> >> +
> >> +Required properties:
> >> +
> >> + - compatible : "analogix,anx7814"
> >> + - reg : I2C address of the device
> >> + - pd-gpios : Which GPIO to use for power down
> >> + - reset-gpios : Which GPIO to use for reset
> >> +
> >> +Example:
> >> +
> >> + anx7814: anx7814@38 {
> >> + compatible = "analogix,anx7814";
> >> + reg = <0x38>;
> >> + pd-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
> >> + reset-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
> >
> > No ports needed for describing data connections?
>
> IMHO I'm not sure if this is applicable here, in this case the bridge
> is transparent so it's not required another device node. For example,
> I've an evaluation board, whre I connect in one side an HDMI input
> signal an in the other side a DP monitor, the driver only configures
> the chip and waits for different events (cable plug, cable unplug, etc
> ..)

But what if the chip is connected to a display controller, for instance to the
HDMI output of an SoC ? Is that a use case for the hardware ?

--
Regards,

Laurent Pinchart



\
 
 \ /
  Last update: 2015-09-10 18:01    [W:0.041 / U:1.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site