lkml.org 
[lkml]   [2015]   [Aug]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 5/5] [media] c8sectpfe: Update DT binding doc with some minor fixes
Hi Lee,

On Fri, 28 Aug 2015, Lee Jones wrote:

> On Thu, 27 Aug 2015, Peter Griffin wrote:
>
> > Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> > ---
> > .../devicetree/bindings/media/stih407-c8sectpfe.txt | 16 +++++++---------
> > 1 file changed, 7 insertions(+), 9 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> > index e70d840..5d6438c 100644
> > --- a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> > +++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
> > @@ -55,21 +55,20 @@ Example:
> > status = "okay";
> > reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
> > reg-names = "stfe", "stfe-ram";
> > - interrupts = <0 34 0>, <0 35 0>;
> > + interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
> > interrupt-names = "stfe-error-irq", "stfe-idle-irq";
> > -
> > - pinctrl-names = "tsin0-serial", "tsin0-parallel", "tsin3-serial",
> > - "tsin4-serial", "tsin5-serial";
> > -
> > + pinctrl-names = "tsin0-serial",
> > + "tsin0-parallel",
> > + "tsin3-serial",
> > + "tsin4-serial",
> > + "tsin5-serial";
> > pinctrl-0 = <&pinctrl_tsin0_serial>;
> > pinctrl-1 = <&pinctrl_tsin0_parallel>;
> > pinctrl-2 = <&pinctrl_tsin3_serial>;
> > pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
> > pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
> > -
> > clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
> > - clock-names = "stfe";
> > -
> > + clock-names = "c8sectpfe";
>
> Are you sure you even need this property? I'm thinking that *-names
> properties are *usually* only required if there are more than one in a
> single property.

Yes that is true, but for tsout and merged input stream
functionality the driver will require additional clocks. As I
mentioned in a previous email I hope to add support for this in the
near future.

>
> > /* tsin0 is TSA on NIMA */
> > tsin0: port@0 {
> > tsin-num = <0>;
> > @@ -78,7 +77,6 @@ Example:
> > reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
> > dvb-card = <STV0367_TDA18212_NIMA_1>;
> > };
> > -
>
> My personal preference is to have a '\n' between nodes.

Yes mine as well, I removed it due to your earlier comment about "superflous \n".
I will add it back in again in v3.

>
> > tsin3: port@3 {
> > tsin-num = <3>;
> > serial-not-parallel;
>
> But these comments are pretty trivial, so agree or not, or fix-up or
> not, it's that big of a deal.

I agree all trivial, but will fixup in v3.
>
> Either way,
> Acked-by: Lee Jones <lee.jones@linaro.org>

Thanks & regards,

Peter.


\
 
 \ /
  Last update: 2015-08-28 19:41    [W:0.076 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site