lkml.org 
[lkml]   [2015]   [Aug]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 2/3] input: Add DT binding documentation for Colibri VF50 touchscreen
On 15-08-22 18:36:54, Stefan Agner wrote:
> On 2015-08-21 06:26, Sanchayan Maity wrote:
> > This adds device tree binding documentation for the Colibri VF50
> > touchscreen driver.
> >
> > Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
> > ---
> > .../bindings/input/touchscreen/colibri-vf50-ts.txt | 36 ++++++++++++++++++++++
> > 1 file changed, 36 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
> > b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
> > new file mode 100644
> > index 0000000..e615aa9
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
> > @@ -0,0 +1,36 @@
> > +* Toradex Colibri VF50 Touchscreen driver
> > +
> > +Required Properties:
> > +- compatible must be toradex,vf50-touchscreen
> > +- io-channels: adc channels being used by the Colibri VF50 module
> > +- xp-gpios: FET gate driver for input of X+
> > +- xm-gpios: FET gate driver for input of X-
> > +- yp-gpios: FET gate driver for input of Y+
> > +- ym-gpios: FET gate driver for input of Y-
> > +- interrupt-parent: phandle for the interrupt controller
> > +- interrupts: pen irq interrupt for touch detection
>
> I like the use of the interrupt interface for the touch detection pin.
> Maybe you can mention here that this is (typically) a GPIO...
>
> > +- pinctrl-names: "idle", "default", "gpios"
> > +- pinctrl-0: pinctrl node for idle state gpio pinmux
> > +- pinctrl-1: pinctrl node for touch detection state pinmux
>
> "touch detection" for default is rather confusing or even wrong. The
> Idle state is used for pen/touch detection, default is used for X/Y and
> Pressure measurement (maybe better described as touch measurement).

Ok. Understood. I see how my wordings can create confusion or are
misleading. Will fix.

- Sanchayan.

>
> > +- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers
> > +- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values
> > +
> > +Example:
> > +
> > + touchctrl: vf50_touchctrl {
> > + compatible = "toradex,vf50-touchscreen";
> > + io-channels = <&adc1 0>,<&adc0 0>,
> > + <&adc0 1>,<&adc1 2>;
> > + xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
> > + xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
> > + yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
> > + ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
> > + interrupt-parent = <&gpio0>;
> > + interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> > + pinctrl-names = "idle","default","gpios";
> > + pinctrl-0 = <&pinctrl_touchctrl_idle>;
> > + pinctrl-1 = <&pinctrl_touchctrl_default>;
> > + pinctrl-2 = <&pinctrl_touchctrl_gpios>;
> > + vf50-ts-min-pressure = <200>;
> > + status = "disabled";
> > + };
>
> Otherwise I agree with 1 and 2:
>
> Acked-by: Stefan Agner <stefan@agner.ch>
>
> --
> Stefan
>


\
 
 \ /
  Last update: 2015-08-23 18:41    [W:0.059 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site