lkml.org 
[lkml]   [2015]   [Jul]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC PATCH v2 1/3] serial: 8250: Fix autoconfig_irq() to avoid race conditions
Date
The following race conditions can happen when a serial port is used
as console.

Case1: CPU_B is used to detect an interrupt from a serial port,
but it can have interrupts disabled during the waiting time.
Case2: CPU_B clears UART_IER just after CPU_A sets UART_IER and then
a serial port may not make an interrupt.
Case3: CPU_A sets UART_IER just after CPU_B clears UART_IER.
This is an unexpected behavior for serial8250_console_write().

CPU_A [autoconfig_irq] | CPU_B [serial8250_console_write]
----------------------------|---------------------------------------
|
probe_irq_on() | spin_lock_irqsave(&port->lock,)
serial_outp(,UART_IER,0x0f) | serial_out(,UART_IER,0)
udelay(20); | uart_console_write()
probe_irq_off() |
| spin_unlock_irqrestore(&port->lock,)

Case1 and 2 can make autoconfig_irq() failed.
In these cases, the console doesn't work in interrupt mode and
"input overrun" (which can make operation mistakes) can happen
on some systems. Especially in the Case1, It is known that the
problem happens with high rate every boot once it occurs
because the boot sequence is always almost same.

port mutex makes sure that the autoconfig operation is exclusive of
any other concurrent HW access except by the console operation.
console lock is required in autoconfig_irq().

Signed-off-by: Taichi Kageyama <t-kageyama@cp.jp.nec.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
---
drivers/tty/serial/8250/8250_core.c | 6 ++++++
1 file changed, 6 insertions(+)

diff --git v4.2-rc4.org/drivers/tty/serial/8250/8250_core.c v4.2-rc4.work/drivers/tty/serial/8250/8250_core.c
index 37fff12..ed1e23e 100644
--- v4.2-rc4.org/drivers/tty/serial/8250/8250_core.c
+++ v4.2-rc4.work/drivers/tty/serial/8250/8250_core.c
@@ -1303,6 +1303,9 @@ static void autoconfig_irq(struct uart_8250_port *up)
inb_p(ICP);
}

+ if (uart_console(port))
+ console_lock();
+
/* forget possible initially masked and pending IRQ */
probe_irq_off(probe_irq_on());
save_mcr = serial_in(up, UART_MCR);
@@ -1334,6 +1337,9 @@ static void autoconfig_irq(struct uart_8250_port *up)
if (port->flags & UPF_FOURPORT)
outb_p(save_ICP, ICP);

+ if (uart_console(port))
+ console_unlock();
+
port->irq = (irq > 0) ? irq : 0;
}

--
2.4.6

\
 
 \ /
  Last update: 2015-07-29 21:10    [W:0.158 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site