lkml.org 
[lkml]   [2015]   [Jul]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 8/8] iio: mma8452: add devicetree property to allow all pin wirings
Am 2015-07-28 um 11:28 schrieb Mark Rutland:
> On Tue, Jul 28, 2015 at 10:11:29AM +0100, Martin Kepplinger wrote:
>>
>>
>> On 2015-07-27 19:33, Mark Rutland wrote:
>>> On Mon, Jul 27, 2015 at 03:37:48PM +0100, Martin Kepplinger wrote:
>>>> Am 2015-07-27 um 16:23 schrieb Mark Rutland:
>>>>> On Mon, Jul 27, 2015 at 03:08:15PM +0100, Martin Kepplinger wrote:
>>>>>> For the devices supported by the mma8452 driver, two interrupt pins are
>>>>>> available to route the interrupt signals to. By default INT1 is assumed.
>>>>>>
>>>>>> This adds a bitmask DT property for users to configure interrupt sources
>>>>>> for INT2, if that is the wired interrupt pin for them.
>>>>>
>>>>> This sounds like configureation rather than a HW property. Why does this
>>>>> need to be in the DT?
>>>>
>>>> It's a hardware property of the board that uses the device. There might
>>>> be boards that connect just one of them at random, which is the reason
>>>> for this DT property. There also might be exotic users who will want
>>>> to use both pins to route different interrupt sources to (not yet
>>>> supported, but no problem with such a bitmask).
>>>
>>> Ok, so I'm somewhat confused as to what the hardware looks like and what
>>> this means.
>>>
>>> Could you elaborate on how INT1 and INT2 are used? It looks like they're
>>> used as output pins, and so interrupt-names would seem appropriate for
>>> describing the combination which is wired up.
>>
>> They are just the chip's two possible interrupt lines for us to get
>> notified about event.
>
> Ok. So that matches my understanding.
>
>> You build a board, you use one of these 4 chips, wiring up just one of
>> the 2 interrupt pins. By far most people won't ever need both pins.
>>
>> DT describes your hardware, right? So you describe how you built your
>> board (wired the accelerometer chip) with this DT property.
>
> Ok.
>
>>> w.r.t. configuring the choice of output(s), that sounds like a runtime
>>> decision rather than something which needs to be configured statically.
>>
>> This won't be useful during runtime. (De)activating events is what you
>> do in iio sysfs.
>>
>> Even in the rare case (maybe supported in the future) when you want one
>> interrupt source on one pin and another source on the other pin, that
>> describes your hardware. You wire, say, data-ready to Linux and
>> motion-detection to some strange alarm system. When you change your
>> hardware (say, use Linux for both pins), I think it would justify
>> changing a DT property.
>
> In that case you would need additional properties anyway.
>
>> Btw, we are talking about very theoretical stuff here. For now (and even
>> possibly forever) we just don't ever want to break a DT propery we
>> introduce here, thus the bitmask.
>
> I don't think you need the bitmask.
>
> I think all you need is interrupt-names, e.g.
>
> dev1 {
> /* both wired up */
> interrupts = <&some_ic 0 47>, <&some_ic 5 62>;
> interrupt-names = "INT1", "INT2";
> }
>
> dev2 {
> /* only INT2 wired up */
> interrupts = <&some_ic 3 96>;
> interrupt-names = "INT2";
> }
>
> You can figure out which interrupts are wired up by trying to acquire
> them by name, then falling back to acquiting an anonymouos interrupt
> (assuming it's INT1) to keep compatible with existing DTBs. You can
> choose which to use arbitrarily, try to load balance, or whatever you'd
> like.
>
> If it's later necessary to route some interrupts to another device,
> additional properties can be added to accomodate that. We already know
> that the bitmask alone is not sufficient for that case.
>

Yes, this sounds reasonable indeed. I like the idea. I'm sorry I won't
rewrite patch 8/8 now. Relocation and a lot to do before holidays. I'll
be happy to write and test this properly in one month from now, if not
done by somebody until then.

Until then, since patches 1-7 only introduce a bindings document, they
shouldn't be problematic for devicetree people.


So if Jonathan and IIO people find anybody for review, feel free to take
patches 1-7. In any case, there is direct register access via debugfs to
at least somehow make the driver work for everybody ;)

so long, thanks.
martin

> Thanks,
> Mark.
>



\
 
 \ /
  Last update: 2015-07-29 20:39    [W:0.074 / U:0.312 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site