lkml.org 
[lkml]   [2015]   [Jun]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/4] dt-binding: power: Add Qualcomm SMBB binding
Date
Add the Qualcomm Switch-Mode Battery Charger and Boost device tree
binding.

Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
---
.../devicetree/bindings/power_supply/qcom_smbb.txt | 137 +++++++++++++++++++++
1 file changed, 137 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power_supply/qcom_smbb.txt

diff --git a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
new file mode 100644
index 000000000000..8a1d75978664
--- /dev/null
+++ b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
@@ -0,0 +1,137 @@
+Qualcomm Switch-Mode Battery Charger and Boost
+
+PROPERTIES
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Description: Must be one of:
+ - "qcom,pm8941-charger"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Description: Base address of registers for SMBB block
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Description: The format of the specifier is defined by the binding document
+ describing the node's interrupt parent. Must contain one
+ specifier for each of the following interrupts, in order:
+ - charge done
+ - charge fast mode
+ - charge trickle mode
+ - battery temperature ok
+ - battery present
+ - charger disconnected
+ - USB-in valid
+ - DC-in valid
+
+- interrupt-names:
+ Usage: required
+ Value type: <stringlist>
+ Description: Must contain the following list, strictly ordered:
+ "chg-done",
+ "chg-fast",
+ "chg-trkl",
+ "bat-temp-ok",
+ "bat-present",
+ "chg-gone",
+ "usb-valid",
+ "dc-valid"
+
+- battery-charge-control-limit:
+ Usage: optional (default: 1A, or pre-configured value)
+ Value type: <u32>; uA; range [100mA : 3A]
+ Description: Maximum charge current; May be clamped to safety limits.
+
+- fast-charge-low-watermark:
+ Usage: optional (default: 3.2V, or pre-configured value)
+ Value type: <u32>; uV; range [2.1V : 3.6V]
+ Description: Battery voltage limit above which fast charging may operate;
+ Below this value linear or switch-mode auto-trickle-charging
+ will operate.
+
+- fast-charge-high-watermark:
+ Usage: optional (default: 4.2V, or pre-configured value)
+ Value type: <u32>; uV; range [3.24V : 5V]
+ Description: Battery voltage limit below which fast charging may operate;
+ The fast charger will attempt to charge the battery to this
+ voltage. May be clamped to safety limits.
+
+- fast-charge-safe-voltage:
+ Usage: optional (default: 4.2V, or pre-configured value)
+ Value type: <u32>; uV; range [3.24V : 5V]
+ Description: Maximum safe battery voltage; May be pre-set by bootloader, in
+ which case, setting this will harmlessly fail. The property
+ 'fast-charge-high-watermark' will be clamped by this value.
+
+- fast-charge-safe-current:
+ Usage: optional (default: 1A, or pre-configured value)
+ Value type: <u32>; uA; range [100mA : 3A]
+ Description: Maximum safe battery charge current; May pre-set by bootloader,
+ in which case, setting this will harmlessly fail. The property
+ 'battery-charge-control-limit' will be clamped by this value.
+
+- auto-recharge-low-watermark:
+ Usage: optional (default: 4.1V, or pre-configured value)
+ Value type: <u32>; uV; range [3.24V : 5V]
+ Description: Battery voltage limit below which auto-recharge functionality
+ will restart charging after end-of-charge; The high cutoff
+ limit for auto-recharge is 5% above this value.
+
+- minimum-input-voltage:
+ Usage: optional (default: 4.3V, or pre-configured value)
+ Value type: <u32>; uV; range [4.2V : 9.6V]
+ Description: Input voltage level above which charging may operate
+
+- usb-charge-control-limit:
+ Usage: optional (default: 100mA, or pre-configured value)
+ Value type: <u32>; uA; range [100mA : 2.5A]
+ Description: Default USB charge current
+
+- dc-charge-control-limit:
+ Usage: optional (default: 100mA, or pre-configured value)
+ Value type: <u32>; uA; range [100mA : 2.5A]
+ Description: Default DC charge current
+
+- disable-dc:
+ Usage: optional (default: false)
+ Value type: boolean: <u32> or <empty>
+ Description: Disable DC charger
+
+- jeita-extended-temp-range:
+ Usage: optional (default: false)
+ Value type: boolean: <u32> or <empty>
+ Description: Enable JEITA extended temperature range; This does *not*
+ adjust the maximum charge voltage or current in the extended
+ temperature range. It only allows charging when the battery
+ is in the extended temperature range. Voltage/current
+ regulation must be done externally to fully comply with
+ the JEITA safety guidelines if this flag is set.
+
+EXAMPLE
+charger@1000 {
+ compatible = "qcom,pm8941-charger";
+ reg = <0x1000 0x700>;
+ interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+ <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+ interrupt-names = "chg-done",
+ "chg-fast",
+ "chg-trkl",
+ "bat-temp-ok",
+ "bat-present",
+ "chg-gone",
+ "usb-valid",
+ "dc-valid";
+
+ battery-charge-control-limit = <1000000>;
+ usb-charge-control-limit = <500000>;
+ dc-charge-control-limit = <1000000>;
+};
--
1.8.2.2


\
 
 \ /
  Last update: 2015-06-18 23:21    [W:0.115 / U:0.372 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site