lkml.org 
[lkml]   [2015]   [Jun]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 5/6] phy: twl4030-usb: add support for reading resistor on ID pin.
Hi,

On Thursday 16 April 2015 01:33 PM, NeilBrown wrote:
> From: NeilBrown <neilb@suse.de>
>
> The twl4030 phy can measure, with low precision, the
> resistance-to-ground of the ID pin.
>
> Add a function to read the value, and export the result
> via sysfs.

Little sceptical about adding new sysfs entries. Do you have a good reason to
add this?

Thanks
Kishon
>
> If the read fails, which it does sometimes, try again in 50msec.
>
> Acked-by: Pavel Machek <pavel@ucw.cz>
> Signed-off-by: NeilBrown <neilb@suse.de>
> ---
> .../ABI/testing/sysfs-platform-twl4030-usb | 22 +++++++
> drivers/phy/phy-twl4030-usb.c | 63 ++++++++++++++++++++
> 2 files changed, 85 insertions(+)
>
> diff --git a/Documentation/ABI/testing/sysfs-platform-twl4030-usb b/Documentation/ABI/testing/sysfs-platform-twl4030-usb
> index 512c51be64ae..425d23676f8a 100644
> --- a/Documentation/ABI/testing/sysfs-platform-twl4030-usb
> +++ b/Documentation/ABI/testing/sysfs-platform-twl4030-usb
> @@ -6,3 +6,25 @@ Description:
> Possible values: "on", "off".
>
> Changes are notified via select/poll.
> +
> +What: /sys/bus/platform/devices/*twl4030-usb/id
> +Description:
> + Read-only report on measurement of USB-OTG ID pin.
> +
> + The ID pin may be floating, grounded, or pulled to
> + ground by a resistor.
> +
> + A very course grained reading of the resistance is
> + available. The numbers given in kilo-ohms are roughly
> + the center-point of the detected range.
> +
> + Possible values are:
> + ground
> + 102k
> + 200k
> + 440k
> + floating
> + unknown
> +
> + "unknown" indicates a problem with trying to detect
> + the resistance.
> diff --git a/drivers/phy/phy-twl4030-usb.c b/drivers/phy/phy-twl4030-usb.c
> index 3a707dd14238..1d6f3e70193e 100644
> --- a/drivers/phy/phy-twl4030-usb.c
> +++ b/drivers/phy/phy-twl4030-usb.c
> @@ -379,6 +379,56 @@ static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
> }
> }
>
> +enum twl4030_id_status {
> + TWL4030_GROUND,
> + TWL4030_102K,
> + TWL4030_200K,
> + TWL4030_440K,
> + TWL4030_FLOATING,
> + TWL4030_ID_UNKNOWN,
> +};
> +static char *twl4030_id_names[] = {
> + "ground",
> + "102k",
> + "200k",
> + "440k",
> + "floating",
> + "unknown"
> +};
> +
> +enum twl4030_id_status twl4030_get_id(struct twl4030_usb *twl)
> +{
> + int ret;
> +
> + pm_runtime_get_sync(twl->dev);
> + if (twl->usb_mode == T2_USB_MODE_ULPI)
> + twl4030_i2c_access(twl, 1);
> + ret = twl4030_usb_read(twl, ULPI_OTG_CTRL);
> + if (ret < 0 || !(ret & ULPI_OTG_ID_PULLUP)) {
> + /* Need pull-up to read ID */
> + twl4030_usb_set_bits(twl, ULPI_OTG_CTRL,
> + ULPI_OTG_ID_PULLUP);
> + mdelay(50);
> + }
> + ret = twl4030_usb_read(twl, ID_STATUS);
> + if (ret < 0 || (ret & 0x1f) == 0) {
> + mdelay(50);
> + ret = twl4030_usb_read(twl, ID_STATUS);
> + }
> +
> + if (twl->usb_mode == T2_USB_MODE_ULPI)
> + twl4030_i2c_access(twl, 0);
> + pm_runtime_put_autosuspend(twl->dev);
> +
> + if (ret < 0)
> + return TWL4030_ID_UNKNOWN;
> + ret = ffs(ret) - 1;
> + if (ret < TWL4030_GROUND || ret > TWL4030_FLOATING)
> + return TWL4030_ID_UNKNOWN;
> +
> + return ret;
> +}
> +
> static void __twl4030_phy_power(struct twl4030_usb *twl, int on)
> {
> u8 pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
> @@ -532,6 +582,16 @@ static ssize_t twl4030_usb_vbus_show(struct device *dev,
> }
> static DEVICE_ATTR(vbus, 0444, twl4030_usb_vbus_show, NULL);
>
> +static ssize_t twl4030_usb_id_show(struct device *dev,
> + struct device_attribute *attr,
> + char *buf)
> +{
> + struct twl4030_usb *twl = dev_get_drvdata(dev);
> + return scnprintf(buf, PAGE_SIZE, "%s\n",
> + twl4030_id_names[twl4030_get_id(twl)]);
> +}
> +static DEVICE_ATTR(id, 0444, twl4030_usb_id_show, NULL);
> +
> static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
> {
> struct twl4030_usb *twl = _twl;
> @@ -709,6 +769,8 @@ static int twl4030_usb_probe(struct platform_device *pdev)
> platform_set_drvdata(pdev, twl);
> if (device_create_file(&pdev->dev, &dev_attr_vbus))
> dev_warn(&pdev->dev, "could not create sysfs file\n");
> + if (device_create_file(&pdev->dev, &dev_attr_id))
> + dev_warn(&pdev->dev, "could not create sysfs file\n");
>
> ATOMIC_INIT_NOTIFIER_HEAD(&twl->phy.notifier);
>
> @@ -753,6 +815,7 @@ static int twl4030_usb_remove(struct platform_device *pdev)
> pm_runtime_get_sync(twl->dev);
> cancel_delayed_work(&twl->id_workaround_work);
> device_remove_file(twl->dev, &dev_attr_vbus);
> + device_remove_file(twl->dev, &dev_attr_id);
>
> /* set transceiver mode to power on defaults */
> twl4030_usb_set_mode(twl, -1);
>
>


\
 
 \ /
  Last update: 2015-06-01 16:01    [W:0.134 / U:149.384 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site