lkml.org 
[lkml]   [2015]   [May]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 2/5] PCI: st: Add Device Tree bindings for sti pcie
On Fri, Apr 10, 2015 at 11:12:45AM +0200, Gabriel FERNANDEZ wrote:
> sti pcie is built around a Synopsis Designware PCIe IP.
>
> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>

Arnd, Rob, can you ack this?

> ---
> Documentation/devicetree/bindings/pci/st-pcie.txt | 53 +++++++++++++++++++++++
> 1 file changed, 53 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/st-pcie.txt
>
> diff --git a/Documentation/devicetree/bindings/pci/st-pcie.txt b/Documentation/devicetree/bindings/pci/st-pcie.txt
> new file mode 100644
> index 0000000..25fcab3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/st-pcie.txt
> @@ -0,0 +1,53 @@
> +STMicroelectronics STi PCIe controller
> +
> +This PCIe host controller is based on the Synopsis Designware PCIe IP
> +and thus inherits all the common properties defined in designware-pcie.txt.
> +
> +Required properties:
> + - compatible: "st,stih407-pcie"
> + - reg: base address and length of the pcie controller, mem-window address
> + and length available to the controller.
> + - interrupts: A list of interrupt outputs of the controller. Must contain an
> + entry for each entry in the interrupt-names property.
> + - interrupt-names: Should be "msi". STi interrupt that is asserted when an
> + MSI is received.
> + - st,syscfg : should be a phandle of the syscfg node. Also contains syscfg
> + offset for IP configuration.
> + - resets, reset-names: the power-down and soft-reset lines of PCIe IP.
> + Associated names must be "powerdown" and "softreset".
> + - phys, phy-names: the phandle for the PHY device.
> + Associated name must be "pcie"
> +
> +Optional properties:
> + - reset-gpio: a GPIO spec to define which pin is connected to the bus reset.
> +
> +Example:
> +
> +pcie0: pcie@9b00000 {
> + compatible = "st,pcie", "snps,dw-pcie";
> + device_type = "pci";
> + reg = <0x09b00000 0x4000>, /* dbi cntrl registers */
> + <0x2fff0000 0x00010000>, /* configuration space */
> + <0x40000000 0x80000000>; /* lmi mem window */
> + reg-names = "dbi", "config", "mem-window";
> + st,syscfg = <&syscfg_core 0xd8 0xe0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges = <0x82000000 0 0x20000000 0x20000000 0 0x0FFF0000>; /* non-prefetchable memory */
> + num-lanes = <1>;
> + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0 0 0 1 &intc GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, /* INT A */
> + <0 0 0 2 &intc GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, /* INT B */
> + <0 0 0 3 &intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, /* INT C */
> + <0 0 0 4 &intc GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; /* INT D */
> +
> + resets = <&powerdown STIH407_PCIE0_POWERDOWN>,
> + <&softreset STIH407_PCIE0_SOFTRESET>;
> + reset-names = "powerdown",
> + "softreset";
> + phys = <&phy_port0 PHY_TYPE_PCIE>;
> + phy-names = "pcie";
> +};
> --
> 1.9.1
>


\
 
 \ /
  Last update: 2015-05-06 00:41    [W:0.318 / U:0.896 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site