lkml.org 
[lkml]   [2015]   [May]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] psmouse - focaltech report finger width to userspace


30.05.2015 02:37, Dmitry Torokhov пишет:
> On Sat, May 30, 2015 at 02:00:59AM +0300, Dmitry Tunin wrote:
>> Focaltech touchpads report finger width in packet[5] of absolute packet.
>> Range for width in raw format is 0x10 - 0x70. Second half-byte is always 0.
>> 0xff is reported, when a large contact area is detected.
>> This can be handled in userspace.
>>
>> Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
>
> Let's add a few people...
>
>> ---
>> drivers/input/mouse/focaltech.c | 20 +++++++++++++++++---
>> 1 file changed, 17 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/input/mouse/focaltech.c b/drivers/input/mouse/focaltech.c
>> index 23d2594..0c3b698 100644
>> --- a/drivers/input/mouse/focaltech.c
>> +++ b/drivers/input/mouse/focaltech.c
>> @@ -105,6 +105,16 @@ struct focaltech_hw_state {
>>
>> /* True if the clickpad has been pressed. */
>> bool pressed;
>> +
>> + /*
>> + * Finger width 0-7 and 15 for a very big contact area.
>> + * 15 value stays until the finger is released.
>> + * Width is reported only in absolute packets.
>> + * Since hardware reports width only for last touching finger,
>> + * there is no need to store width for every specific finger, so
>> + * we keep only last value reported.
>> + */
>> + unsigned int width;
>> };
>>
>> struct focaltech_data {
>> @@ -112,7 +122,7 @@ struct focaltech_data {
>> struct focaltech_hw_state state;
>> };
>>
>> -static void focaltech_report_state(struct psmouse *psmouse)
>> +static void focaltech_report_state(struct psmouse *psmouse, bool abs)
>> {
>> struct focaltech_data *priv = psmouse->private;
>> struct focaltech_hw_state *state = &priv->state;
>> @@ -137,6 +147,7 @@ static void focaltech_report_state(struct psmouse *psmouse)
>> input_report_abs(dev, ABS_MT_POSITION_X, clamped_x);
>> input_report_abs(dev, ABS_MT_POSITION_Y,
>> priv->y_max - clamped_y);
>> + if (abs) input_report_abs(dev, ABS_TOOL_WIDTH, state->width);
>
> I am not sure this condition and the change in focaltech_process_packet
> are needed. The relative packets augment absolute one and we expect
> width not change so we can always report state->width (either updated or
> cached) and input core will drop dupes.
>
>> }
>> }
>> input_mt_report_pointer_emulation(dev, true);
>> @@ -187,6 +198,7 @@ static void focaltech_process_abs_packet(struct psmouse *psmouse,
>>
>> state->fingers[finger].x = ((packet[1] & 0xf) << 8) | packet[2];
>> state->fingers[finger].y = (packet[3] << 8) | packet[4];
>> + state->width = packet[5] >> 4;
>> state->fingers[finger].valid = true;
>> }
>>
>> @@ -228,22 +240,23 @@ static void focaltech_process_packet(struct psmouse *psmouse)
>> switch (packet[0] & 0xf) {
>> case FOC_TOUCH:
>> focaltech_process_touch_packet(psmouse, packet);
>> + focaltech_report_state(psmouse, false);
>> break;
>>
>> case FOC_ABS:
>> focaltech_process_abs_packet(psmouse, packet);
>> + focaltech_report_state(psmouse, true);
>> break;
>>
>> case FOC_REL:
>> focaltech_process_rel_packet(psmouse, packet);
>> + focaltech_report_state(psmouse, false);
>> break;
>>
>> default:
>> psmouse_err(psmouse, "Unknown packet type: %02x\n", packet[0]);
>> break;
>> }
>> -
>> - focaltech_report_state(psmouse);
>> }
>>
>> static psmouse_ret_t focaltech_process_byte(struct psmouse *psmouse)
>> @@ -331,6 +344,7 @@ static void focaltech_set_input_params(struct psmouse *psmouse)
>> __set_bit(EV_ABS, dev->evbit);
>> input_set_abs_params(dev, ABS_MT_POSITION_X, 0, priv->x_max, 0, 0);
>> input_set_abs_params(dev, ABS_MT_POSITION_Y, 0, priv->y_max, 0, 0);
>> + input_set_abs_params(dev, ABS_TOOL_WIDTH, 0, 15, 0, 0);
>> input_mt_init_slots(dev, 5, INPUT_MT_POINTER);
>> __set_bit(INPUT_PROP_BUTTONPAD, dev->propbit);
>> }
>> --
>> 1.9.1
>>
>
> Thanks.
>
Hi Dmitry,

I tested it again and it appears that you are correct. In previous versions I stored width of each finger in state->fingers[finger].width.
And it confused everything up. Then I changed it to state->width, because there is only one relevant width.
Really duplicates are removed. I am sending v 2.



\
 
 \ /
  Last update: 2015-05-30 16:41    [W:0.066 / U:2.108 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site