[lkml]   [2015]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v10 0/4] PCI: X-Gene: Add APM X-Gene v1 MSI/MSIX termination driver
This patch set adds MSI/MSIX termination driver support for APM X-Gene v1 SoC.
APM X-Gene v1 SoC supports its own implementation of MSI, which is not compliant
to GIC V2M specification for MSI Termination.

There is single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16 physical
HW IRQ lines and shared across all 5 PCIe ports. Starting from version 5 of
this patch series, the total MSI vectors this driver supports is reduced to 256
to maintain the correct set_affinity behavior for each MSI.

v10 changes:
1. Remove inline in helper functions
2. Simplify hwirq_to_cpu implementation

v9 changes:
1. Add more helpers for manipulating MSI messages
2. Improve code readability
3. Make PCI_XGENE_MSI selectable

v8 changes:
1. Add helper to read MSI registers
2. Resample interrupt status of the same group after handling interrupts
in that group
3. Error handling in case fail to allocate CPU mask for affinity setting

v7 changes:
1. Add more error handling cases
2. Clear spurious interrupts that may happen during driver probe
3. Not using free_irq for chained irqs
4. Improve GIC IRQ number look up in chained handler

v6 changes:
1. Correctly allocate MSI with bitmap_find_next_zero_area
2. Add notifier for CPU hotplug case
3. Driver clean up
4. Add more detailed information into device tree binding document
and move the device tree binding patch before the driver/dts patch

v5 changes:
1. Implement set_affinity for each MSI by statically allocating 2
MSI GIC IRQs for each X-Gene CPU core and moving MSI vectors around
these GIC IRQs to steer them to target CPU core. As a consequence,
the total MSI vectors that X-Gene v1 supports is reduced to 256.

v4 changes:
1. Remove affinity setting for each MSI
2. Add description about register layout, MSI termination address
and data
3. Correct total number of MSI vectors to 2048
4. Clean up error messages
5. Remove unused module code

v3 changes:
1. Implement MSI support using PCI MSI IRQ domain
2. Only use msi_controller to store IRQ domain

v2 changes:
1. Use msi_controller structure
2. Remove arch hooks arch_teardown_msi_irqs and arch_setup_msi_irqs

.../devicetree/bindings/pci/xgene-pci-msi.txt | 68 +++
arch/arm64/boot/dts/apm/apm-storm.dtsi | 27 +
drivers/pci/host/Kconfig | 10 +
drivers/pci/host/Makefile | 1 +
drivers/pci/host/pci-xgene-msi.c | 595 +++++++++++++++++++++
drivers/pci/host/pci-xgene.c | 21 +
7 files changed, 730 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/xgene-pci-msi.txt
create mode 100644 drivers/pci/host/pci-xgene-msi.c


 \ /
  Last update: 2015-05-29 20:41    [W:0.135 / U:3.984 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site