lkml.org 
[lkml]   [2015]   [May]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 10/13] staging: lustre: lnet: lnet: checkpatch.pl fixes
From
Date
On Fri, 2015-05-22 at 21:16 +0000, Drokin, Oleg wrote:
> On May 22, 2015, at 11:42 AM, Joe Perches wrote:
>
> > On Fri, 2015-05-22 at 08:08 +0000, Drokin, Oleg wrote:
> >> On May 22, 2015, at 1:06 AM, Julia Lawall wrote:
> >>
> >>> On Thu, 21 May 2015, Michael Shuey wrote:
> >>>
> >>>> That's a task (of many) I've been putting on the back burner until the code
> >>>> is cleaner. It's also a HUGE change, since there are debug macros
> >>>> everywhere, and they all check a #define'd mask to see if they should fire,
> >>>> and the behavior is likely governed by parts of the lustre user land tools
> >>>> as well.
> >>>>
> >>>> Suggestions are welcome. Do other parts of the linux kernel define complex
> >>>> debugging macros like these, or is this a lustre-ism? Any suggestions on
> >>>> how to handle this more in line with existing drivers?
> >>>
> >>> Once you decide what to do, you can use Coccinelle to make the changes for
> >>> you. So you shouldn't be put off by the number of code sites to change.
> >>>
> >>> The normal functions are pr_err, pr_warn, etc. Perhaps you can follow
> >>> Joe's suggestions if you really need something more complicated.
> >>
> >> Ideally leaving CERROR/CDEBUG in Lustre would be desirable from my perspective.
> >
> > My issue with CERROR is the name is little misleading.
> > It's actually a debugging message.
> > #define CERROR(format, ...) CDEBUG_LIMIT(D_ERROR, format, ## __VA_ARGS__)
>
> Except it's not a debugging message.
> There is a clear distinction.

Not really. If the first reading sjows that the mechanism it
goes through is called CDEBUG, a reasonable expectation should
be that it's a debugging message.

> CERROR is something that get's printed on the console, because it's believed
> to be serious error (At least that's how the theory for it's usage goes).
> It also gets rate-limited so that the console does not get overflown.
> (but the debug buffer gets the full version).
> (there's also LCONSOLE that always get's printed, but it does not get the
> prefixes like line numbers and stuff).
>
> CDEBUG on the other hand is a debugging message (of which ERROR messages are
> sort of a subset (D_ERROR mask)). You can fine-tune those to be noops or
> to go into console or to debug buffer only. Most of those are doing nothing
> because they are off in the default debug mask, until actually enabled.
>
> That CERROR usees CDEBUG underneath is just to share some common infrastructure.
>
> > I think it'd be clearer as
> > lustre_debug(ERROR, ...
> > even if the name and use style is a little longer.
>
> I wonder what is more clear about that in your opinion ve
> lustre_error/lustre_debug?

The fact that you have to explain this shows that it's
at least misleading unless you completely understand the
code.

It'd be more intelligible if this CERROR became lustre_err
and the actual debugging uses were lustre_dbg

Perhaps it needs a better explanation somewhere not in the
code but in some external documentation. I haven't looked.



\
 
 \ /
  Last update: 2015-05-23 02:41    [W:1.234 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site