lkml.org 
[lkml]   [2015]   [May]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] sc16is7xx: spi interface is added
On Thu, 14 May 2015 13:16:20 +0530, ram kiran wrote:
> > On Wed, 13 May 2015 16:27:58 +0530, ram.i hcltech wrote:
> >> spi interface for sc16is7xx is added along with Kconfig flag
> >> to enable spi or i2c, thus in a instance we can have either
> >> spi or i2c or both, in sync to the hw.
> >>
> >> Signed-off-by: ram.i hcltech <indrakanti_ram@hotmail.com>
> >> ---
> >>
> >> Changes in v2:
> >> -Added seprate flags for i2c and spi
> >> -Added space in the comments lines
> >> -Added MODULE_ALIAS for spi interface
> >> ---
> >> drivers/tty/serial/Kconfig | 27 +++++++++++++++--
> >> drivers/tty/serial/sc16is7xx.c | 69 +++++++++++++++++++++++++++++++++++++++++-
> >> 2 files changed, 92 insertions(+), 4 deletions(-)
> >>
> >> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> >> index f8120c1..8c505b2 100644
> >> --- a/drivers/tty/serial/Kconfig
> >> +++ b/drivers/tty/serial/Kconfig
> >> @@ -1181,13 +1181,34 @@ config SERIAL_SCCNXP_CONSOLE
> >>
> To avoid error or warning on build, i think this would be the probable solution.
> I thinking to go with this, any comments on this please.
>
> config SERIAL_SC16IS7XX
>     bool
>
> config SERIAL_SC16IS7XX_SELECT
>     tristate "SC16IS7xx serial support"
>     select SERIAL_CORE
>     depends on I2C || SPI_MASTER
>     select REGMAP_I2C if I2C
>     select REGMAP_SPI if SPI_MASTER
>     help
>       This selects support for SC16IS7xx serial ports.
>       Supported ICs are SC16IS740, SC16IS741, SC16IS750, SC16IS752,
>       SC16IS760 and SC16IS762. Select supported buses using options below.
>
> config SERIAL_SC16IS7XX_I2C
>     bool "SC16IS7xx for I2C interface"
>     depends on SERIAL_SC16IS7XX_SELECT
>     select SERIAL_SC16IS7XX
>     default y
>     help
>       Enable SC16IS7xx driver on I2C bus.
>
> config SERIAL_SC16IS7XX_SPI
>     bool "SC16IS7xx for spi interface"
>     depends on SERIAL_SC16IS7XX_SELECT
>     select SERIAL_SC16IS7XX
>     help
>       Enable SC16IS7xx driver on SPI bus.
>

This looks quite elegant! Should we aslo make SERIAL_SC16IS7XX depend
on SERIAL_SC16IS7XX_I2C || SERIAL_SC16IS7XX_SPI? Would that work?

I know little about kbuild but I'm worried that someone doing oldconfig
can still get SERIAL_SC16IS7XX selected while saying no to all the
others.

Other option would be to swap the names between SERIAL_SC16IS7XX and
SERIAL_SC16IS7XX_SELECT, oldconfig would run smoother.

Thanks!


\
 
 \ /
  Last update: 2015-05-14 10:41    [W:0.079 / U:0.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site