lkml.org 
[lkml]   [2015]   [Apr]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH V2] drivers/rtc/rtc-ds1307.c: Enable the mcp794xx alarm after programming time
Hi,

On 04/21/2015 03:51 AM, Nishanth Menon wrote:
> Alarm interrupt enable register is at offset 0x7, while the time
> registers for the alarm follow that. When we program Alarm interrupt
> enable prior to programming the time, it is possible that previous
> time value could be close or match at the time of alarm enable
> resulting in interrupt trigger which is unexpected (and does not match
> the time we expect it to trigger).
>
> To prevent this scenario from occuring, program the ALM0_EN bit only
> after the alarm time is appropriately programmed.
>
> Ofcourse, I2C programming is non-atomic, so there are loopholes where
> the interrupt wont trigger if the time requested is in the past at
> the time of programming the ALM0_EN bit. However, we will not have
> unexpected interrupts while the time is programmed after the interrupt
> are enabled.

I think it will be nice if you will mention that you going to follow
vendor recommendations - AN1491 Configuring the MCP794XX RTCC Family
http://ww1.microchip.com/downloads/en/AppNotes/01491A.pdf
;)
"Also, it is recommended that the alarm registers be loaded
before the alarm is enabled."

>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
> Changes in v2:
> - minor typo fix in comments
> - merged up code that I missed committing in
>
> V1: https://patchwork.kernel.org/patch/6245041/
>
> drivers/rtc/rtc-ds1307.c | 12 ++++++------
> 1 file changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
> index 4ffabb322a9a..3cd4783375a5 100644
> --- a/drivers/rtc/rtc-ds1307.c
> +++ b/drivers/rtc/rtc-ds1307.c
> @@ -742,17 +742,17 @@ static int mcp794xx_set_alarm(struct device *dev, struct rtc_wkalrm *t)
> regs[6] &= ~MCP794XX_BIT_ALMX_IF;
> /* Set alarm match: second, minute, hour, day, date, month. */
> regs[6] |= MCP794XX_MSK_ALMX_MATCH;
> -
> - if (t->enabled)
> - regs[0] |= MCP794XX_BIT_ALM0_EN;
> - else
> - regs[0] &= ~MCP794XX_BIT_ALM0_EN;
> + /* Disable interrupt. We will not enable until completely programmed */
> + regs[0] &= ~MCP794XX_BIT_ALM0_EN;
>
> ret = ds1307->write_block_data(client, MCP794XX_REG_CONTROL, 10, regs);
> if (ret < 0)
> return ret;
>
> - return 0;
> + if (!t->enabled)
> + return 0;
> + regs[0] |= MCP794XX_BIT_ALM0_EN;
> + return i2c_smbus_write_byte_data(client, MCP794XX_REG_CONTROL, regs[0]);

So, It seems, that right sequence should be:
- disable alarmX
- read alarmX regs
- configure alarmX regs
- load alarmX regs
- enable alarmX

More over, looks like, alarm/alarm IRQ should be enabled/disabled separately from set_alarm/RTC_ALM_SET
by RTC_AIE_ON, RTC_AIE_OFF. Should it?

> }
>
> static int mcp794xx_alarm_irq_enable(struct device *dev, unsigned int enabled)
>


--
regards,
-grygorii


\
 
 \ /
  Last update: 2015-04-22 16:01    [W:0.297 / U:0.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site