lkml.org 
[lkml]   [2015]   [Apr]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] drivers/rtc/rtc-ds1307.c: Enable the mcp794xx alarm after programming time
On 04/20/2015 06:55 PM, Nishanth Menon wrote:
> Alarm interrupt enable register is at offset 0x7, while the time
> registers for the alarm follow that. When we program Alarm interrupt
> enable prior to programming the time, it is possible that previous
> time value could be close or match at the time of alarm enable
> resulting in interrupt trigger which is unexpected (and does not match
> the time we expect it to trigger).
>
> To prevent this scenario from occurring, program the ALM0_EN bit only
> after the alarm time is appropriately programmed.
>
> Of course, I2C programming is non-atomic, so there are loopholes where
> the interrupt wont trigger if the time requested is in the past at
> the time of programming the ALM0_EN bit. However, we will not have
> unexpected interrupts while the time is programmed after the interrupt
> are enabled.
>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
> drivers/rtc/rtc-ds1307.c | 12 ++++++------
> 1 file changed, 6 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
> index 4ffabb322a9a..59f9ecf323d5 100644
> --- a/drivers/rtc/rtc-ds1307.c
> +++ b/drivers/rtc/rtc-ds1307.c
> @@ -742,17 +742,17 @@ static int mcp794xx_set_alarm(struct device *dev, struct rtc_wkalrm *t)
> regs[6] &= ~MCP794XX_BIT_ALMX_IF;
> /* Set alarm match: second, minute, hour, day, date, month. */
> regs[6] |= MCP794XX_MSK_ALMX_MATCH;
> -
> - if (t->enabled)
> - regs[0] |= MCP794XX_BIT_ALM0_EN;
> - else
> - regs[0] &= ~MCP794XX_BIT_ALM0_EN;
> + /* Disable interrupt. We will not enable until completely programed */
^^ typo here. s/programed/programmed
> + regs[0] &= ~MCP794XX_BIT_ALM0_EN;
>
> ret = ds1307->write_block_data(client, MCP794XX_REG_CONTROL, 10, regs);
> if (ret < 0)
> return ret;
>
> - return 0;
> + if (!t->enabled)
> + return 0;
> + regs[0] |= MCP7941X_BIT_ALM0_EN;

^^ messed up git commit --amend :(

> + return i2c_smbus_write_byte_data(client, MCP794XX_REG_CONTROL, regs[0]);
> }
>
> static int mcp794xx_alarm_irq_enable(struct device *dev, unsigned int enabled)
>

will repost a rev2 - apologies on the noise.
--
Regards,
Nishanth Menon


\
 
 \ /
  Last update: 2015-04-21 02:41    [W:0.046 / U:0.848 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site