lkml.org 
[lkml]   [2015]   [Apr]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v2 2/2] extcon-axp288: Add axp288 extcon driver support
Hi Ramakrishna,

When I apply this patch for build test on extcon-next branch,
conflict happen. you have to implement this patchset on latest extcon-next branch.

Also, This patch must need more clean-up and use latest extcon helper API.
When you implement extcon-axp288.c, I recommend you refer to merged extcon drivers.

On 04/03/2015 04:19 AM, Ramakrishna Pallala wrote:
> This patch adds the extcon support for AXP288 PMIC which
> has the BC1.2 charger detection capability. Additionally
> it also adds the USB mux switching support b/w SOC and PMIC
> based on GPIO control.
>
> Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
> ---
> drivers/extcon/Kconfig | 7 +
> drivers/extcon/Makefile | 1 +
> drivers/extcon/extcon-axp288.c | 479 ++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 5 +
> 4 files changed, 492 insertions(+)
> create mode 100644 drivers/extcon/extcon-axp288.c
>
> diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
> index 6a1f7de..b8627f7 100644
> --- a/drivers/extcon/Kconfig
> +++ b/drivers/extcon/Kconfig
> @@ -93,4 +93,11 @@ config EXTCON_SM5502
> Silicon Mitus SM5502. The SM5502 is a USB port accessory
> detector and switch.
>
> +config EXTCON_AXP288
> + tristate "AXP288 EXTCON support"

I recommend to add manufactor name of AXP288 PMIC chip.

> + depends on MFD_AXP20X && USB_PHY
> + help
> + Say Y here to enable support for USB peripheral detection
> + and USB MUX switching by AXP288 PMIC.
> +

Need to relocate EXTCON_AXP288 configuration alpabetically.

> endif # MULTISTATE_SWITCH
> diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
> index 0370b42..832ad79 100644
> --- a/drivers/extcon/Makefile
> +++ b/drivers/extcon/Makefile
> @@ -12,3 +12,4 @@ obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o
> obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o
> obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o
> obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o
> +obj-$(CONFIG_EXTCON_AXP288) += extcon-axp288.o

ditto.

> diff --git a/drivers/extcon/extcon-axp288.c b/drivers/extcon/extcon-axp288.c
> new file mode 100644
> index 0000000..2e75d45
> --- /dev/null
> +++ b/drivers/extcon/extcon-axp288.c
> @@ -0,0 +1,479 @@
> +/*
> + * extcon-axp288.c - X-Power AXP288 PMIC extcon cable detection driver
> + *
> + * Copyright (C) 2015 Intel Corporation
> + * Ramakrishna Pallala <ramakrishna.pallala@intel.com>

Need to add 'Author' in front of name.

> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/io.h>
> +#include <linux/slab.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +#include <linux/usb/phy.h>
> +#include <linux/notifier.h>
> +#include <linux/extcon.h>
> +#include <linux/regmap.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/mfd/axp20x.h>
> +
> +#define AXP288_PS_STAT_REG 0x00
> +#define PS_STAT_VBUS_TRIGGER (1 << 0)
> +#define PS_STAT_BAT_CHRG_DIR (1 << 2)
> +#define PS_STAT_VBUS_ABOVE_VHOLD (1 << 3)
> +#define PS_STAT_VBUS_VALID (1 << 4)
> +#define PS_STAT_VBUS_PRESENT (1 << 5)
> +
> +#define AXP288_BC_GLOBAL_REG 0x2c
> +#define BC_GLOBAL_RUN (1 << 0)
> +#define BC_GLOBAL_DET_STAT (1 << 2)
> +#define BC_GLOBAL_DBP_TOUT (1 << 3)
> +#define BC_GLOBAL_VLGC_COM_SEL (1 << 4)
> +#define BC_GLOBAL_DCD_TOUT_MASK 0x60
> +#define BC_GLOBAL_DCD_TOUT_300MS 0x0
> +#define BC_GLOBAL_DCD_TOUT_100MS 0x1
> +#define BC_GLOBAL_DCD_TOUT_500MS 0x2
> +#define BC_GLOBAL_DCD_TOUT_900MS 0x3
> +#define BC_GLOBAL_DCD_DET_SEL (1 << 7)
> +
> +#define AXP288_BC_VBUS_CNTL_REG 0x2d
> +#define VBUS_CNTL_DPDM_PD_EN (1 << 4)
> +#define VBUS_CNTL_DPDM_FD_EN (1 << 5)
> +#define VBUS_CNTL_FIRST_PO_STAT (1 << 6)
> +
> +#define AXP288_BC_USB_STAT_REG 0x2e
> +#define USB_STAT_BUS_STAT_MASK 0x0f
> +#define USB_STAT_BUS_STAT_OFFSET 0
> +#define USB_STAT_BUS_STAT_ATHD 0x0
> +#define USB_STAT_BUS_STAT_CONN 0x1
> +#define USB_STAT_BUS_STAT_SUSP 0x2
> +#define USB_STAT_BUS_STAT_CONF 0x3
> +#define USB_STAT_USB_SS_MODE (1 << 4)
> +#define USB_STAT_DEAD_BAT_DET (1 << 6)
> +#define USB_STAT_DBP_UNCFG (1 << 7)
> +
> +#define AXP288_BC_DET_STAT_REG 0x2f
> +#define DET_STAT_MASK 0xe0
> +#define DET_STAT_OFFSET 5
> +#define DET_STAT_SDP 0x1
> +#define DET_STAT_CDP 0x2
> +#define DET_STAT_DCP 0x3
> +
> +#define AXP288_PS_BOOT_REASON_REG 0x2
> +
> +#define AXP288_PWRSRC_IRQ_CFG_REG 0x40
> +#define PWRSRC_IRQ_CFG_MASK 0x1c
> +
> +#define AXP288_BC12_IRQ_CFG_REG 0x45
> +#define BC12_IRQ_CFG_MASK 0x2

I recommend to gather axp288 registers as following
by using 'enum' keyword and then add the mask definition
using the BIT(n) macro.

enum axp288_reg {
AXP288_REG_PS_STAT_REG = 0x00,
AXP288_REG_BC_GLOBAL_REG = 0x2c,
AXP288_REG_BC_VBUS_CNTL_REG = 0x2d,
AXP288_REG_BC_USB_STAT_REG = 0x2e,
AXP288_REG_BC_DET_STAT_REG = 0x2f,
...

AXP288_REG_END
};

Also, I think need more description about mask/offset definition.

> +
> +#define AXP288_PWRSRC_INTR_NUM 4

Don't need this definition. You can add AXP288_

> +
> +#define AXP288_DRV_NAME "axp288_extcon"

Don't need this definition. You use drive name in structure axp288_extcon_driver.

> +
> +#define AXP288_EXTCON_CABLE_SDP "Slow-charger"
> +#define AXP288_EXTCON_CABLE_CDP "Charge-downstream"
> +#define AXP288_EXTCON_CABLE_DCP "Fast-charger"

Use the capital letter for cable name instead of small letter.
I'll change all cable names by using captical letter.

> +
> +#define EXTCON_GPIO_MUX_SEL_PMIC 0
> +#define EXTCON_GPIO_MUX_SEL_SOC 1
> +
> +enum {

Need to add enum name to improve readability
and catch the correct meaning of this definitions.

> + VBUS_FALLING_IRQ = 0,
> + VBUS_RISING_IRQ,
> + MV_CHNG_IRQ,
> + BC_USB_CHNG_IRQ,

If AXP288_PWRSRC_INTR_NUM means the number of this interrupt,
you can add AXP288_PWRSRC_INTR_NUM value in this enum list
without separate defintion (#define AXP288_PWRSRC_INTR_NUM).

> +};
> +
> +static const char *axp288_extcon_cables[] = {
> + AXP288_EXTCON_CABLE_SDP,
> + AXP288_EXTCON_CABLE_CDP,
> + AXP288_EXTCON_CABLE_DCP,
> + NULL,
> +};
> +
> +struct axp288_extcon_info {
> + struct platform_device *pdev;

Define 'struct device *dev' instead of 'struct platform_device *pdev'.
I think you can support all case by using 'dev' instance in extcon driver.

> + struct regmap *regmap;
> + struct regmap_irq_chip_data *regmap_irqc;
> + struct axp288_extcon_pdata *pdata;

Are you sure that pdata is necessary? The axp288_extcon_pdata includes only gpio.
You have to get the gpio value by using gpiod helper funciton as following:
You can refer other extcon driver(extcon-usb-gpio.c)/

devm_gpiod_get(dev, "mux_cntl");

> + int irq[AXP288_PWRSRC_INTR_NUM];
> + struct extcon_dev *edev;
> + struct usb_phy *otg;
> + struct notifier_block extcon_nb;
> + struct extcon_specific_cable_nb cable;
> + bool is_sdp;

I can't find any 'if statemenet' using 'is_sdp' variable.
Just this driver store the false or true to 'is_sdp'.
Remove the 'is_sdp'.


> + bool usb_id_short;

What is meaning of usb_id_short? You need to add the description.

> +};
> +
> +static char *pwr_up_down_info[] = {

Add 'axp288' prefix to array name.

> + /* bit 0 */ "Last wake caused by user pressing the power button",
> + /* bit 2 */ "Last wake caused by a charger insertion",
> + /* bit 1 */ "Last wake caused by a battery insertion",
> + /* bit 3 */ "Last wake caused by SOC initiated global reset",
> + /* bit 4 */ "Last wake caused by cold reset",
> + /* bit 5 */ "Last shutdown caused by PMIC UVLO threshold",
> + /* bit 6 */ "Last shutdown caused by SOC initiated cold off",
> + /* bit 7 */ "Last shutdown caused by user pressing the power button",

I don't prefer to add following comment in front of each entry.

/* bit x */

> + NULL,
> +};

Need to add more detailed description why this array is necessary.

> +
> +/*
> + * Decode and log the given "reset source indicator"
> + * register and then clear it.
> + */
> +static void axp288_extcon_log_rsi(struct axp288_extcon_info *info,
> + char **pwrsrc_rsi_info, int reg)
> +{
> + char **rsi;

What is meaning of 'rsi'?

> + unsigned int val, i, clear_mask = 0;
> + int ret;
> +
> + ret = regmap_read(info->regmap, reg, &val);
> + for (i = 0, rsi = pwrsrc_rsi_info; *rsi; rsi++, i++) {
> + if (val & BIT(i)) {
> + dev_dbg(&info->pdev->dev, "%s\n", *rsi);
> + clear_mask |= BIT(i);
> + }
> + }
> +
> + /* Clear the register value for next reboot (write 1 to clear bit) */
> + regmap_write(info->regmap, reg, clear_mask);
> +}
> +
> +static int handle_chrg_det_event(struct axp288_extcon_info *info)
> +{
> + static bool notify_otg, notify_charger;
> + static char *cable;
> + int ret, stat, cfg, pwr_stat;
> + u8 chrg_type;
> + bool vbus_attach = false;
> +
> + ret = regmap_read(info->regmap, AXP288_PS_STAT_REG, &pwr_stat);
> + if (ret < 0) {
> + dev_err(&info->pdev->dev, "vbus status read error\n");
> + return ret;
> + }
> +
> + vbus_attach = (pwr_stat & PS_STAT_VBUS_PRESENT) && !info->usb_id_short;
> + if (vbus_attach) {
> + dev_dbg(&info->pdev->dev, "vbus present\n");
> + } else {
> + dev_dbg(&info->pdev->dev, "vbus not present\n");
> + goto notify_otg;
> + }
> +
> + /* Check charger detection completion status */
> + ret = regmap_read(info->regmap, AXP288_BC_GLOBAL_REG, &cfg);
> + if (ret < 0)
> + goto dev_det_ret;
> + if (cfg & BC_GLOBAL_DET_STAT) {
> + dev_dbg(&info->pdev->dev, "charger detection not complete!!\n");
> + goto dev_det_ret;
> + }
> +
> + ret = regmap_read(info->regmap, AXP288_BC_DET_STAT_REG, &stat);
> + if (ret < 0)
> + goto dev_det_ret;
> + dev_dbg(&info->pdev->dev, "stat:%x, cfg:%x\n", stat, cfg);
> +
> + chrg_type = (stat & DET_STAT_MASK) >> DET_STAT_OFFSET;
> + info->is_sdp = false;
> +
> + if (chrg_type == DET_STAT_SDP) {
> + dev_dbg(&info->pdev->dev, "sdp cable connecetd\n");
> + notify_otg = true;
> + notify_charger = true;
> + info->is_sdp = true;
> + cable = AXP288_EXTCON_CABLE_SDP;
> + } else if (chrg_type == DET_STAT_CDP) {
> + dev_dbg(&info->pdev->dev, "cdp cable connecetd\n");
> + notify_otg = true;
> + notify_charger = true;
> + cable = AXP288_EXTCON_CABLE_CDP;
> + } else if (chrg_type == DET_STAT_DCP) {
> + dev_dbg(&info->pdev->dev, "dcp cable connecetd\n");
> + notify_charger = true;
> + cable = AXP288_EXTCON_CABLE_DCP;
> + } else {
> + dev_warn(&info->pdev->dev,
> + "disconnect or unknown or ID event\n");
> + }
> +
> +notify_otg:
> + if (notify_otg) {
> + /*
> + * If VBUS is absent Connect D+/D- lines to PMIC for BC
> + * detection. Else connect them to SOC for USB communication.
> + */
> + if (info->pdata->gpio_mux_cntl != NULL)
> + gpiod_set_value(info->pdata->gpio_mux_cntl,
> + vbus_attach ? EXTCON_GPIO_MUX_SEL_SOC
> + : EXTCON_GPIO_MUX_SEL_PMIC);
> +
> + atomic_notifier_call_chain(&info->otg->notifier,
> + vbus_attach ? USB_EVENT_VBUS : USB_EVENT_NONE, NULL);
> + }
> +
> + if (notify_charger)
> + extcon_set_cable_state(info->edev, cable, vbus_attach);
> +
> + /* Clear the flags on disconnect event */
> + if (!vbus_attach) {
> + notify_otg = false;
> + notify_charger = false;
> + }
> +
> + return 0;
> +
> +dev_det_ret:
> + if (ret < 0)
> + dev_warn(&info->pdev->dev, "BC Mod detection error\n");
> +
> + return ret;
> +}
> +
> +static irqreturn_t axp288_extcon_isr(int irq, void *data)
> +{
> + struct axp288_extcon_info *info = data;
> + unsigned int i;
> + int ret;
> +
> + for (i = 0; i < AXP288_PWRSRC_INTR_NUM; i++) {
> + if (info->irq[i] == irq)
> + break;
> + }
> +
> + if (i == AXP288_PWRSRC_INTR_NUM) {
> + dev_warn(&info->pdev->dev, "spurious interrupt!!\n");
> + return IRQ_NONE;
> + }
> +
> + ret = handle_chrg_det_event(info);
> + if (ret < 0)
> + dev_warn(&info->pdev->dev, "error in PWRSRC INT handling\n");
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int axp288_extcon_registration(struct axp288_extcon_info *info)
> +{
> + int ret;
> +
> + /* Register with extcon */
> + info->edev = devm_kzalloc(&info->pdev->dev,
> + sizeof(struct extcon_dev), GFP_KERNEL);

Use devm_extcon_dev_allocate() instead of devm_kzalloc()

> + if (!info->edev)
> + return -ENOMEM;
> +
> + info->edev->name = "extcon-axp288";

Don't need to assing extcon device name. extcon_dev_register() will use the
device name as extcon device name.

> + info->edev->supported_cable = axp288_extcon_cables;
> + ret = extcon_dev_register(info->edev);

Use devm_extcon_dev_register() instead of extcon_dev_register.

> + if (ret)
> + dev_err(&info->pdev->dev, "extcon registration failed!!\n");
> +
> + return ret;
> +}

Don't need seprate this function. I prefer to execute devm_extcon_* function in probe funtion.

> +
> +static inline bool is_usb_host_mode(struct extcon_dev *evdev)
> +{
> + return !!evdev->state;
> +}

The state of extcon_dev means the state of all supported cables.
If you want to get the state of specific cable, you can use
extcon_get_cable_state().

> +
> +static int axp288_handle_extcon_event(struct notifier_block *nb,
> + unsigned long event, void *param)
> +{
> + struct axp288_extcon_info *info =
> + container_of(nb, struct axp288_extcon_info, extcon_nb);
> + struct extcon_dev *edev = param;
> + int usb_host = is_usb_host_mode(edev);
> +
> + dev_info(&info->pdev->dev,
> + "[extcon notification] evt:USB-Host val:%s\n",

I recommend to use the standard log mesasge and use dev_dbg instead of dev_info.
I think following message is very specific log.
[extcon notification] evt:USB-Host val:

> + usb_host ? "Connected" : "Disconnected");
> +
> + /*
> + * Set usb_id_short flag to avoid running charger detection logic
> + * in case usb host.
> + */
> + info->usb_id_short = usb_host;
> +
> + /*
> + * Connect the USB mux to SOC in case of usb host else connect
> + * it to PMIC.
> + */
> + if (info->pdata->gpio_mux_cntl != NULL) {

As I commented, need to remove pdata.

> + dev_dbg(&info->pdev->dev,
> + "usb_id_short=%d\n", info->usb_id_short);

Ditto. Need to modify log message.

> + if (info->usb_id_short)
> + gpiod_set_value(info->pdata->gpio_mux_cntl,
> + EXTCON_GPIO_MUX_SEL_SOC);
> + else
> + gpiod_set_value(info->pdata->gpio_mux_cntl,
> + EXTCON_GPIO_MUX_SEL_PMIC);
> + }
> +
> + return NOTIFY_OK;
> +}
> +
> +static int axp288_init_gpio_mux_cntl(struct axp288_extcon_info *info)
> +{
> + int ret;
> +
> + ret = gpio_request(desc_to_gpio(info->pdata->gpio_mux_cntl), "USB_MUX");
> + if (ret < 0) {
> + dev_err(&info->pdev->dev,
> + "usb mux gpio request failed:gpio=%d\n",
> + desc_to_gpio(info->pdata->gpio_mux_cntl));

You can change the error message as following:
"Failed to request the gpio"

> + return ret;
> + }
> + gpiod_direction_output(info->pdata->gpio_mux_cntl,
> + EXTCON_GPIO_MUX_SEL_PMIC);
> +
> + info->extcon_nb.notifier_call = axp288_handle_extcon_event;
> + ret = extcon_register_interest(&info->cable, NULL,
> + "USB-Host", &info->extcon_nb);

NAK.

Why do you register notifier_chain in this driver?

Only extcon provider driver can be included int drivers/extcon/ directory.
extcon_register_interest() function should be used for extcon consumer driver.

> + if (ret) {
> + dev_err(&info->pdev->dev, "failed to register extcon notifier\n");
> + return ret;
> + }
> +
> + if (info->cable.edev)
> + info->usb_id_short =
> + is_usb_host_mode(info->cable.edev);
> + if (info->usb_id_short)
> + gpiod_set_value(info->pdata->gpio_mux_cntl,
> + EXTCON_GPIO_MUX_SEL_SOC);
> +
> + return 0;
> +}
> +
> +static int axp288_extcon_probe(struct platform_device *pdev)
> +{
> + struct axp288_extcon_info *info;
> + struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
> + int ret, i, pirq;
> +
> + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
> + if (!info)
> + return -ENOMEM;
> +
> + info->pdev = pdev;
> + info->regmap = axp20x->regmap;
> + info->regmap_irqc = axp20x->regmap_irqc;

If axp288_extcon_info structure includes the axp20x_dev structure,
info->regmap and info->regmap_irqc is not necessary.

> + info->pdata = pdev->dev.platform_data;

I don't prefer to use platform_data. You have to get the platform data
from devicetree by using OF helper function.

> +
> + if (!info->pdata) {
> + /* TODO: Try ACPI provided pdata via device properties */
> + if (!device_property_present(&pdev->dev,
> + "axp288_extcon_data\n"))
> + dev_err(&pdev->dev, "no platform data\n");
> + return -ENODEV;
> + }
> + platform_set_drvdata(pdev, info);
> +
> + axp288_extcon_log_rsi(info, pwr_up_down_info,
> + AXP288_PS_BOOT_REASON_REG);

I need more detailed description.

> +
> + /* Register extcon device */
> + ret = axp288_extcon_registration(info);
> + if (ret < 0)
> + goto extcon_reg_failed;

Remove the call of axp288_extcon_registration()

> +
> + /* Get otg transceiver phy */
> + info->otg = usb_get_phy(USB_PHY_TYPE_USB2);
> + if (IS_ERR(info->otg)) {
> + dev_warn(&info->pdev->dev, "Failed to get otg transceiver!!\n");
> + ret = PTR_ERR(info->otg);
> + goto otg_reg_failed;
> + }
> +
> + for (i = 0; i < AXP288_PWRSRC_INTR_NUM; i++) {
> + pirq = platform_get_irq(pdev, i);
> + info->irq[i] = regmap_irq_get_virq(info->regmap_irqc, pirq);
> + if (info->irq[i] < 0) {
> + dev_warn(&info->pdev->dev,
> + "regmap_irq get virq failed for IRQ %d: %d\n",
> + pirq, info->irq[i]);
> + info->irq[i] = -1;
> + goto intr_reg_failed;
> + }
> + ret = request_threaded_irq(info->irq[i],

Use devm_request_threaded_irq().

> + NULL, axp288_extcon_isr,
> + IRQF_ONESHOT, AXP288_DRV_NAME, info);

You can use pdev->name instead of AXP288_DRV_NAME.

> + if (ret) {
> + dev_err(&pdev->dev, "request_irq fail :%d err:%d\n",
> + info->irq[i], ret);
> + goto intr_reg_failed;
> + }
> + }
> +
> + /* Set up gpio control for USB Mux */
> + if (info->pdata->gpio_mux_cntl != NULL) {
> + ret = axp288_init_gpio_mux_cntl(info);
> + if (ret < 0)
> + goto intr_reg_failed;
> + }
> +
> + /* Unmask VBUS interrupt */
> + regmap_write(info->regmap, AXP288_PWRSRC_IRQ_CFG_REG,
> + PWRSRC_IRQ_CFG_MASK);
> + regmap_update_bits(info->regmap, AXP288_BC_GLOBAL_REG,
> + BC_GLOBAL_RUN, 0);
> + /* Unmask the BC1.2 complte interrupts */
> + regmap_write(info->regmap, AXP288_BC12_IRQ_CFG_REG, BC12_IRQ_CFG_MASK);
> + /* Enable the charger detection logic */
> + regmap_update_bits(info->regmap, AXP288_BC_GLOBAL_REG,
> + BC_GLOBAL_RUN, BC_GLOBAL_RUN);
> +
> + return 0;
> +
> +intr_reg_failed:
> + for (; i > 0; i--) {
> + free_irq(info->irq[i - 1], info);
> + info->irq[i - 1] = -1;
> + }
> + usb_put_phy(info->otg);
> +otg_reg_failed:
> + extcon_dev_unregister(info->edev);
> +extcon_reg_failed:
> + return ret;
> +}
> +
> +static int axp288_extcon_remove(struct platform_device *pdev)
> +{
> + struct axp288_extcon_info *info = platform_get_drvdata(pdev);
> + int i;
> +
> + for (i = 0; i < AXP288_PWRSRC_INTR_NUM; i++)
> + free_irq(info->irq[i], info);

Don't need to free interrupt if you use devm_request_threaded_irq().

> + usb_put_phy(info->otg);
> + extcon_dev_unregister(info->edev);

Don't need to unregister extcon device if you use devm_extcon_*.

> + return 0;
> +}
> +
> +static struct platform_driver axp288_extcon_driver = {
> + .probe = axp288_extcon_probe,
> + .remove = axp288_extcon_remove,
> + .driver = {
> + .name = AXP288_DRV_NAME,
> + },
> +};
> +module_platform_driver(axp288_extcon_driver);
> +
> +MODULE_AUTHOR("Ramakrishna Pallala <ramakrishna.pallala@intel.com>");
> +MODULE_DESCRIPTION("X-Powers AXP288 extcon driver");
> +MODULE_LICENSE("GPL");
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index dfabd6d..4ed8071 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -275,4 +275,9 @@ struct axp20x_fg_pdata {
> int thermistor_curve[MAX_THERM_CURVE_SIZE][2];
> };
>
> +struct axp288_extcon_pdata {
> + /* GPIO pin control to switch D+/D- lines b/w PMIC and SOC */
> + struct gpio_desc *gpio_mux_cntl;
> +};
> +
> #endif /* __LINUX_MFD_AXP20X_H */
>

Thanks,
Chanwoo Choi


\
 
 \ /
  Last update: 2015-04-03 06:21    [W:0.195 / U:0.316 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site