lkml.org 
[lkml]   [2015]   [Apr]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH V1 6/6] devicetree: da9062: Add bindings for DA9062 driver
From: S Twiss <stwiss.opensource@diasemi.com>

Add device tree bindings for the DA9062 driver

Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>

---

This patch applies against linux-next and v4.0



Documentation/devicetree/bindings/mfd/da9062.txt | 107 +++++++++++++++++++++++
1 file changed, 107 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/da9062.txt

diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt
new file mode 100644
index 0000000..cf8f3f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9062.txt
@@ -0,0 +1,107 @@
+* Dialog DA9062 Power Management Integrated Circuit (PMIC)
+
+DA9062 consists of a large and varied group of sub-devices:
+
+Device Supply Names Description
+------ ------------ -----------
+da9062-regulator : : LDOs & BUCKs
+da9062-onkey : : On Key
+da9062-rtc : : Real-Time Clock
+da9062-watchdog : : Watchdog Timer
+
+======
+
+Required properties:
+
+- compatible : Should be "dlg,da9062".
+- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
+ modified to match the chip's OTP settings).
+- interrupt-parent : Specifies the reference to the interrupt controller for
+ the DA9062.
+- interrupts : IRQ line information.
+- interrupt-controller
+
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
+further information on IRQ bindings.
+
+Sub-nodes:
+
+- regulators : This node defines the settings for the LDOs and BUCKs. The
+ DA9062 regulators are bound using their names listed below:
+
+ buck1 : BUCK_1
+ buck2 : BUCK_2
+ buck3 : BUCK_3
+ buck4 : BUCK_4
+ ldo1 : LDO_1
+ ldo2 : LDO_2
+ ldo3 : LDO_3
+ ldo4 : LDO_4
+
+ The component follows the standard regulator framework and the bindings
+ details of individual regulator device can be found in:
+ Documentation/devicetree/bindings/regulator/regulator.txt
+
+
+- rtc : This node defines settings required for the Real-Time Clock associated
+ with the DA9062. There are currently no entries in this binding, however
+ compatible = "dlg,da9062-rtc" should be added if a node is created.
+
+
+- onkey : This node defines the OnKey settings for controlling the key
+ functionality of the device. The node should contain the compatible property
+ with the value "dlg,da9062-onkey".
+
+ Optional onkey properties:
+
+ - dlg,disable-key-power : Disable power-down using a long key-press. If this
+ entry exists the OnKey driver will remove support for the KEY_POWER key
+ press. If this entry does not exist then by default the key-press
+ triggered power down is enabled and the OnKey will support both KEY_POWER
+ and KEY_SLEEP.
+
+- watchdog: This node defines the settings for the watchdog driver associated
+ with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added
+ if a node is created.
+
+
+Example:
+
+ pmic0: da9062@58 {
+ compatible = "dlg,da9062";
+ reg = <0x58>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ rtc {
+ compatible = "dlg,da9062-rtc";
+ };
+
+ onkey {
+ compatible = "dlg,da9062-onkey";
+ dlg,disable-key-power;
+ };
+
+ watchdog {
+ compatible = "dlg,da9062-watchdog";
+ };
+
+ regulators {
+ DA9062_BUCK1: buck1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1570000>;
+ regulator-min-microamp = <500000>;
+ regulator-max-microamp = <2000000>;
+ regulator-boot-on;
+ };
+ DA9062_LDO1: ldo1 {
+ regulator-name = "LDO_1";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-boot-on;
+ };
+ };
+ };
+
--
end-of-patch for PATCH V1


\
 
 \ /
  Last update: 2015-04-17 17:01    [W:0.269 / U:12.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site