lkml.org 
[lkml]   [2015]   [Apr]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 3/3] phy: cygnus-usbphy: Add Broadcom Cygnus USB phy driver
Hi Kishon

I will address your comments on multi level if and error checking.
I have replied to your comments on phy power on and power off. Thanks

Arun
On 15-04-03 08:14 AM, Kishon Vijay Abraham I wrote:
> Hi,
>
> On Thursday 02 April 2015 02:20 AM, Arun Ramamurthy wrote:
>> This driver adds support for USB 2.0 host and device phy for
>> Broadcom's Cygnus chipset. The host controller is connected to
>> three separate phys and one of the phys (port 2) is connected to
>> the device controller
>>
>> Reviewed-by: Ray Jui <rjui@broadcom.com>
>> Reviewed-by: Scott Branden <sbranden@broadcom.com>
>> Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
>> ---
>> drivers/phy/Kconfig | 12 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-bcm-cygnus-usb.c | 484
>> +++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 497 insertions(+)
>> create mode 100644 drivers/phy/phy-bcm-cygnus-usb.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 2962de2..0aa62dc 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -291,4 +291,16 @@ config PHY_QCOM_UFS
>> help
>> Support for UFS PHY on QCOM chipsets.
>>
>> +config PHY_BCM_CYGNUS_USB
>> + tristate "Broadcom Cygnus USB PHY support"
>> + depends on OF
>> + depends on ARCH_BCM_CYGNUS || COMPILE_TEST
>> + select GENERIC_PHY
>> + default ARCH_BCM_CYGNUS
>> + help
>> + Enable this to support the USB PHY in Broadcom's Cygnus chip.
>> + The phys are capable of supporting host mode for all ports
>> + and device mode for port 2. The host or device configuration is
>> + read from the device tree.
>> +
>> endmenu
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index f080e1b..47a37fa 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -6,6 +6,7 @@ obj-$(CONFIG_GENERIC_PHY) += phy-core.o
>> obj-$(CONFIG_PHY_BERLIN_USB) += phy-berlin-usb.o
>> obj-$(CONFIG_PHY_BERLIN_SATA) += phy-berlin-sata.o
>> obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY) += phy-armada375-usb2.o
>> +obj-$(CONFIG_PHY_BCM_CYGNUS_USB) += phy-bcm-cygnus-usb.o
>> obj-$(CONFIG_BCM_KONA_USB2_PHY) += phy-bcm-kona-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
>> obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
>> diff --git a/drivers/phy/phy-bcm-cygnus-usb.c
>> b/drivers/phy/phy-bcm-cygnus-usb.c
>> new file mode 100644
>> index 0000000..b017e3b
>> --- /dev/null
>> +++ b/drivers/phy/phy-bcm-cygnus-usb.c
>> @@ -0,0 +1,484 @@
>> +/*
>> + * Copyright (C) 2015 Broadcom Corporation
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/module.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/io.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/delay.h>
>> +
>> +#define CDRU_USBPHY_CLK_RST_SEL_OFFSET 0x11b4
>> +#define CDRU_USBPHY2_HOST_DEV_SEL_OFFSET 0x11b8
>> +#define CDRU_SPARE_REG_0_OFFSET 0x1238
>> +#define CRMU_USB_PHY_AON_CTRL_OFFSET 0x00028
>> +#define CDRU_USB_DEV_SUSPEND_RESUME_CTRL_OFFSET 0x1210
>> +#define CDRU_USBPHY_P0_STATUS_OFFSET 0x11D0
>> +#define CDRU_USBPHY_P1_STATUS_OFFSET 0x11E8
>> +#define CDRU_USBPHY_P2_STATUS_OFFSET 0x1200
>> +#define CDRU_USBPHY_USBPHY_ILDO_ON_FLAG 1
>> +#define CDRU_USBPHY_USBPHY_PLL_LOCK 0
>> +#define CDRU_USB_DEV_SUSPEND_RESUME_CTRL_DISABLE 0
>> +#define PHY2_DEV_HOST_CTRL_SEL_HOST 1
>> +
>> +#define CRMU_USBPHY_P0_AFE_CORERDY_VDDC 1
>> +#define CRMU_USBPHY_P0_RESETB 2
>> +#define CRMU_USBPHY_P1_AFE_CORERDY_VDDC 9
>> +#define CRMU_USBPHY_P1_RESETB 10
>> +#define CRMU_USBPHY_P2_AFE_CORERDY_VDDC 17
>> +#define CRMU_USBPHY_P2_RESETB 18
>> +
>> +#define USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET 0x0408
>> +#define USB2_IDM_IDM_IO_CONTROL_DIRECT__clk_enable 0
>
> Did you run checkpatch on this patch?
I did run checkpatch and it passed. However I can see that the
indentation is ok, I will address that.
>> +#define USB2_IDM_IDM_RESET_CONTROL_OFFSET 0x0800
>> +#define USB2_IDM_IDM_RESET_CONTROL__RESET 0
>> +
>> +#define PLL_LOCK_RETRY_COUNT 1000
>> +#define MAX_PHY_PORTS 3
>> +
>> +static int power_bit[] = {CRMU_USBPHY_P0_AFE_CORERDY_VDDC,
>> + CRMU_USBPHY_P1_AFE_CORERDY_VDDC,
>> + CRMU_USBPHY_P2_AFE_CORERDY_VDDC};
>> +static int reset_bit[] = {CRMU_USBPHY_P0_RESETB,
>> + CRMU_USBPHY_P1_RESETB,
>> + CRMU_USBPHY_P2_RESETB};
>> +static int status_reg[] = {CDRU_USBPHY_P0_STATUS_OFFSET,
>> + CDRU_USBPHY_P1_STATUS_OFFSET,
>> + CDRU_USBPHY_P2_STATUS_OFFSET};
>> +
>> +struct bcm_phy_instance;
>> +
>> +struct bcm_phy_driver {
>> + void __iomem *usbphy_regs;
>> + void __iomem *usb2h_idm_regs;
>> + void __iomem *usb2d_idm_regs;
>> + struct bcm_phy_instance *ports[MAX_PHY_PORTS];
>> + spinlock_t lock;
>> + bool idm_host_enabled;
>> +};
>> +
>> +struct bcm_phy_instance {
>> + struct bcm_phy_driver *driver;
>> + struct phy *generic_phy;
>> + int port_no;
>> + bool host_mode; /* true - Host, false - device */
>> + bool power;
>> +};
>> +
>> +static inline int bcm_phy_cdru_usbphy_status_wait(u32 usb_reg, int
>> reg_bit,
>> + struct bcm_phy_driver *phy_driver)
>> +{
>> + /* Wait for the PLL lock status */
>> + int retry = PLL_LOCK_RETRY_COUNT;
>> + u32 reg_val;
>> +
>> + do {
>> + udelay(1);
>> + reg_val = readl(phy_driver->usbphy_regs +
>> + usb_reg);
>> + if (reg_val & (1 << reg_bit))
>> + return 0;
>> + } while (--retry > 0);
>> +
>> + return -EBUSY;
>> +
>> +}
>> +
>> +static struct phy *bcm_usb_phy_xlate(struct device *dev,
>> + struct of_phandle_args *args)
>> +{
>> + struct bcm_phy_driver *phy_driver = dev_get_drvdata(dev);
>> + struct bcm_phy_instance *port = NULL;
>> + int i;
>> +
>> + if (!phy_driver)
>> + return ERR_PTR(-EINVAL);
>
> use ENODEV here to make phy_optional_get happy.

>> +
>> + if (WARN_ON(args->args_count != 1))
>> + return ERR_PTR(-EINVAL);
>
> same here..

>> +
>> + if (WARN_ON(args->args[0] < 0 || args->args[0] > 1))
>> + return ERR_PTR(-EINVAL);
>
> here..

>> +
>> + for (i = 0; i < ARRAY_SIZE(phy_driver->ports); i++) {
>> + struct bcm_phy_instance *p = phy_driver->ports[i];
>> +
>> + if (p && p->generic_phy->dev.of_node == args->np) {
>> + port = p;
>> + break;
>> + }
>> + }
>> +
>> + if (!port) {
>> + dev_err(dev, "Failed to locate phy %s\n", args->np->name);
>> + return ERR_PTR(-EINVAL);
>> + }
>> +
>> + port->host_mode = args->args[0];
>> +
>> + return port->generic_phy;
>> +}
>> +
>> +static int bcm_phy_init(struct phy *generic_phy)
>> +{
>> + struct bcm_phy_instance *port = phy_get_drvdata(generic_phy);
>> + struct bcm_phy_driver *phy_driver = port->driver;
>> + unsigned long flags;
>> + u32 reg_val;
>> +
>> + spin_lock_irqsave(&phy_driver->lock, flags);
>
> if (port->port_no != 2)
> return;
>
> avoids multi level if..else.

>> +
>> + /*
>> + * Only PORT 2 is capable of being device and host
>> + * Default setting is device, check if it is set to host.
>> + */
>> + if (port->port_no == 2) {
>> + if (port->host_mode) {
>> + writel(PHY2_DEV_HOST_CTRL_SEL_HOST,
>> + phy_driver->usbphy_regs +
>> + CDRU_USBPHY2_HOST_DEV_SEL_OFFSET);
>> + } else {
>> + /*
>> + * Disable suspend/resume signals to device controller
>> + * when a port is in device mode.
>> + */
>> + reg_val = readl(phy_driver->usbphy_regs +
>> + CDRU_USB_DEV_SUSPEND_RESUME_CTRL_OFFSET);
>> + reg_val |=
>> + 1 << CDRU_USB_DEV_SUSPEND_RESUME_CTRL_DISABLE;
>> + writel(reg_val, phy_driver->usbphy_regs +
>> + CDRU_USB_DEV_SUSPEND_RESUME_CTRL_OFFSET);
>> + }
>> + }
>> +
>> + spin_unlock_irqrestore(&phy_driver->lock, flags);
>> + return 0;
>> +}
>> +
>> +static int bcm_phy_shutdown(struct phy *generic_phy)
>> +{
>> + struct bcm_phy_instance *port = phy_get_drvdata(generic_phy);
>> + struct bcm_phy_driver *phy_driver = port->driver;
>> + unsigned long flags;
>> + int i;
>> + u32 reg_val, powered_on_phy;
>> + bool power_off_flag = true;
>> +
>> + spin_lock_irqsave(&phy_driver->lock, flags);
>> +
>> + /* power down the phy */
>> + reg_val = readl(phy_driver->usbphy_regs +
>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>> + reg_val &= ~(1 << power_bit[port->port_no]);
>> + reg_val &= ~(1 << reset_bit[port->port_no]);
>> + writel(reg_val, phy_driver->usbphy_regs +
>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>> + port->power = false;
>> +
>> + /*
>> + * If a port is configured to device and it is being shutdown,
>> + * turn off the clocks to the usb device controller.
>> + */
>> + if (port->port_no == 2 && !port->host_mode) {
>> + reg_val = readl(phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> + reg_val &= ~(1 << USB2_IDM_IDM_IO_CONTROL_DIRECT__clk_enable);
>> + writel(reg_val, phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> +
>> + reg_val = readl(phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>> + reg_val |= 1 << USB2_IDM_IDM_RESET_CONTROL__RESET;
>> + writel(reg_val, phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>
> just do a spin_unlock_irqrestore and return here. With that we can remove
> multiple levels of if..else.
>> + } else {
>> + /*
>> + * If the phy being shutdown provides clock and reset to
>> + * the host controller, change it do a different powered on phy
> %s/do/to/
>
> Won't this cause a glitch or something?
We might submit patches for this later, we are still doing some testing.
>
>> + * If all phys are powered off, shut of the host controller
>> + */
>> + reg_val = readl(phy_driver->usbphy_regs +
>> + CDRU_USBPHY_CLK_RST_SEL_OFFSET);
>> + powered_on_phy = reg_val;
>> + if (reg_val == port->port_no) {
>> + for (i = 0; i < ARRAY_SIZE(phy_driver->ports); i++) {
>> + if (phy_driver->ports[i] &&
>> + phy_driver->ports[i]->power &&
>> + phy_driver->ports[i]->host_mode) {
>> + power_off_flag = false;
>> + powered_on_phy = i;
> "break" here?
>> + }
>> + }
>> + }
>> +
>> + if (power_off_flag) {
>> + /*
>> + * Put the host controller into reset state and
>> + * disable clock.
>> + */
>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> + reg_val &=
>> + ~(1 << USB2_IDM_IDM_IO_CONTROL_DIRECT__clk_enable);
>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> +
>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>> + reg_val |= (1 << USB2_IDM_IDM_RESET_CONTROL__RESET);
>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>> + phy_driver->idm_host_enabled = 0;
>> + } else {
>> + writel(powered_on_phy, phy_driver->usbphy_regs +
>> + CDRU_USBPHY_CLK_RST_SEL_OFFSET);
>> + }
>> + }
>> +
>> + spin_unlock_irqrestore(&phy_driver->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +static int bcm_phy_poweron(struct phy *generic_phy)
>> +{
>> + struct bcm_phy_instance *port = phy_get_drvdata(generic_phy);
>> + struct bcm_phy_driver *phy_driver = port->driver;
>> + unsigned long flags;
>> + int ret;
>> + u32 reg_val;
>> + bool clock_reset_flag = true;
>> +
>> + spin_lock_irqsave(&phy_driver->lock, flags);
>> +
>> + /* Bring the AFE block out of reset to start powering up the PHY */
>> + reg_val = readl(phy_driver->usbphy_regs +
>> CRMU_USB_PHY_AON_CTRL_OFFSET);
>> + reg_val |= 1 << power_bit[port->port_no];
>> + writel(reg_val, phy_driver->usbphy_regs +
>> CRMU_USB_PHY_AON_CTRL_OFFSET);
>> +
>> + /* Check for power on and PLL lock */
>> + ret = bcm_phy_cdru_usbphy_status_wait(status_reg[port->port_no],
>> + CDRU_USBPHY_USBPHY_ILDO_ON_FLAG, phy_driver);
>> + if (ret < 0) {
>> + dev_err(&generic_phy->dev,
>> + "Timed out waiting for USBPHY_ILDO_ON_FLAG on port %d",
>> + port->port_no);
>> + goto err_shutdown;
>> + }
>> + ret = bcm_phy_cdru_usbphy_status_wait(status_reg[port->port_no],
>> + CDRU_USBPHY_USBPHY_PLL_LOCK, phy_driver);
>> + if (ret < 0) {
>> + dev_err(&generic_phy->dev,
>> + "Timed out waiting for USBPHY_PLL_LOCK on port %d",
>> + port->port_no);
>> + goto err_shutdown;
>> + }
>> + port->power = true;
>> +
>> + /* Check if the port 2 is configured for device */
>> + if (port->port_no == 2 && !port->host_mode) {
>> + /*
>> + * Enable clock to USB device and get the USB device
>> + * out of reset.
>> + */
>> + reg_val = readl(phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> + reg_val |= 1 << USB2_IDM_IDM_IO_CONTROL_DIRECT__clk_enable;
>> + writel(reg_val, phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> +
>> + reg_val = readl(phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>> + reg_val &= ~(1 << USB2_IDM_IDM_RESET_CONTROL__RESET);
>> + writel(reg_val, phy_driver->usb2d_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>> +
>> + } else {
>> + reg_val = readl(phy_driver->usbphy_regs +
>> + CDRU_USBPHY_CLK_RST_SEL_OFFSET);
>> +
>> + /*
>> + * Check if the phy that is configured to provide clock
>> + * and reset is powered on.
>> + */
>> + if (reg_val >= 0 && reg_val < ARRAY_SIZE(phy_driver->ports))
>> + if (phy_driver->ports[reg_val])
>> + if (phy_driver->ports[reg_val]->power)
>> + clock_reset_flag = false;
>> +
>> + /* if not set the current phy */
>> + if (clock_reset_flag) {
>> + reg_val = port->port_no;
>> + writel(reg_val, phy_driver->usbphy_regs +
>> + CDRU_USBPHY_CLK_RST_SEL_OFFSET);
>
> Not sure if this is the right thing to do. We don't want to be powering on
> some other PHY when the request was to enable this PHY. Same w.r.t
> shutdown.
This logic is to check if the phy specified in the
CDRU_USBPHY_CLK_RST_SEL_OFFSET is turned on. If it is not, the register
value is changed to this current phy that is being powered on. We do not
power on any other phys
>> + }
>> + }
>> +
>> + if (!phy_driver->idm_host_enabled) {
>> + /* Enable clock to USB and get the USB out of reset */
>
> What if one PHY resets the USB when another is using it?
This reset is for the HOST controller and not the phy. The
idm_host_enabled flag will prevent a PHY from powering on and resetting
the controller if another phy has already done so.
>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> + reg_val |= 1 << USB2_IDM_IDM_IO_CONTROL_DIRECT__clk_enable;
>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>> +
>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>> + reg_val &= ~(1 << USB2_IDM_IDM_RESET_CONTROL__RESET);
>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>> + phy_driver->idm_host_enabled = true;
>> + }
>> +
>> + spin_unlock_irqrestore(&phy_driver->lock, flags);
>> + return 0;
>> +
>> +err_shutdown:
>> + spin_unlock_irqrestore(&phy_driver->lock, flags);
>> + bcm_phy_shutdown(generic_phy);
>> + return ret;
>> +}
>> +
>> +static struct phy_ops ops = {
>> + .init = bcm_phy_init,
>> + .power_on = bcm_phy_poweron,
>> + .power_off = bcm_phy_shutdown,
>> +};
>> +
>> +static const struct of_device_id bcm_phy_dt_ids[] = {
>> + { .compatible = "brcm,cygnus-usb-phy", },
>> + { }
>> +};
>> +
>> +static int bcm_phy_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct bcm_phy_driver *phy_driver;
>> + struct phy_provider *phy_provider;
>> + struct device_node *child;
>> + struct resource *res;
>> + int error;
>> + u32 reg_val;
>> +
>> + phy_driver = devm_kzalloc(dev, sizeof(struct bcm_phy_driver),
>> + GFP_KERNEL);
>> + if (!phy_driver)
>> + return -ENOMEM;
>> +
>> + spin_lock_init(&phy_driver->lock);
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> check return value of res.
>
will fix
>> + phy_driver->usbphy_regs = devm_ioremap_nocache(dev, res->start,
>> + resource_size(res));
>> + if (!phy_driver->usbphy_regs) {
>> + dev_err(dev, "Failed to remap usbphy_regs\n");
>> + return -ENOMEM;
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> same here..
>
will fix
>> + phy_driver->usb2h_idm_regs = devm_ioremap_nocache(dev, res->start,
>> + resource_size(res));
>> + if (!phy_driver->usb2h_idm_regs) {
>> + dev_err(dev, "Failed to remap usb2h_idm_regs\n");
>> + return -ENOMEM;
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
>
> here too..
will fix
>> + phy_driver->usb2d_idm_regs = devm_ioremap_nocache(dev, res->start,
>> + resource_size(res));
>> + if (!phy_driver->usb2d_idm_regs) {
>> + dev_err(dev, "Failed to remap usb2d_idm_regs\n");
>> + return -ENOMEM;
>> + }
>> +
>> + dev_set_drvdata(dev, phy_driver);
>> +
>> + phy_driver->idm_host_enabled = false;
>> +
>> + /* Shut down all ports. They can be powered up as required */
>> + reg_val = readl(phy_driver->usbphy_regs +
>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>> + reg_val &= ~(1 << CRMU_USBPHY_P0_AFE_CORERDY_VDDC);
>> + reg_val &= ~(1 << CRMU_USBPHY_P0_RESETB);
>> + reg_val &= ~(1 << CRMU_USBPHY_P1_AFE_CORERDY_VDDC);
>> + reg_val &= ~(1 << CRMU_USBPHY_P1_RESETB);
>> + reg_val &= ~(1 << CRMU_USBPHY_P2_AFE_CORERDY_VDDC);
>> + reg_val &= ~(1 << CRMU_USBPHY_P2_RESETB);
>> + writel(reg_val, phy_driver->usbphy_regs +
>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>> +
>> + for_each_available_child_of_node(dev->of_node, child) {
>> + struct bcm_phy_instance *port;
>> + u32 port_no;
>> +
>> + if (of_property_read_u32(child, "reg", &port_no)) {
>> + dev_err(dev, "missing reg property in node %s\n",
>> + child->name);
>> + return -EINVAL;
>> + }
>> +
>> + if (port_no >= ARRAY_SIZE(phy_driver->ports)) {
>> + dev_err(dev, "invalid reg in node %s: %u\n",
>> + child->name, port_no);
>> + return -EINVAL;
>> + }
>> +
>> + port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
>> + if (!port)
>> + return -ENOMEM;
>> +
>> + port->generic_phy = devm_phy_create(dev, child, &ops);
>> + if (IS_ERR(port->generic_phy)) {
>> + error = PTR_ERR(port->generic_phy);
>> + dev_err(dev, "Failed to create phy %u: %d",
>> + port_no, error);
>> + return error;
>> + }
>> +
>> + port->port_no = port_no;
>> + port->driver = phy_driver;
>> + phy_set_drvdata(port->generic_phy, port);
>> +
>> + phy_driver->ports[port_no] = port;
>> + }
>> +
>> + phy_provider = devm_of_phy_provider_register(dev,
>> bcm_usb_phy_xlate);
>> + if (IS_ERR(phy_provider)) {
>> + error = PTR_ERR(phy_provider);
>> + dev_err(dev, "Failed to register as phy provider: %d\n",
>> + error);
>> + return error;
>> + }
>> +
>> + platform_set_drvdata(pdev, phy_driver);
>
> dev_get_drvdata should be sufficient.
>
I assume you mean dev_set_drvdata. Will fix.
> Thanks
> Kishon


\
 
 \ /
  Last update: 2015-04-15 00:21    [W:3.125 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site