lkml.org 
[lkml]   [2015]   [Apr]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/3] Phy: DT binding documentation for Broadcom Cygnus USB PHY driver
Date
Broadcom's Cygnus chip has a USB 2.0 host controller connected to
three separate phys. One of the phs (port 2) is also connectd to
a usb 2.0 device controller

Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
.../bindings/phy/brcm,cygnus-usb-phy.txt | 69 ++++++++++++++++++++++
1 file changed, 69 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt

diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
new file mode 100644
index 0000000..d1a9a65
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt
@@ -0,0 +1,69 @@
+BROADCOM CYGNUS USB PHY
+
+Required Properties:
+ - compatible: brcm,cygnus-usb-phy
+ - reg : usbphy_regs - Base address of phy registers
+ usb2h_idm_regs - Base address of host idm registers
+ usb2d_idm_regs - Base address of device idm registers
+ - phy-cells - must be 1 for each port declared. This is because the node
+ that uses the phy must provide one integers, 0 for device
+ and 1 for host
+
+NOTE: port 0 and port 1 are host only and port 2 can be configured for host or
+device.
+
+Example of phy :
+ usbphy0: usbphy@0x0301c000 {
+ compatible = "brcm,cygnus-usb-phy";
+ reg = <0x0301c000 0x2000>,
+ <0x18115000 0x1000>,
+ <0x18111000 0x1000>;
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ usbphy0_0: usbphy0@0 {
+ #phy-cells = <1>;
+ reg = <0>;
+ status = "okay";
+ phy-supply = <&vbus_p0>;
+ };
+
+ usbphy0_1: usbphy0@1 {
+ #phy-cells = <1>;
+ reg = <1>;
+ status = "okay";
+ };
+
+ usbphy0_2: usbphy0@2 {
+ #phy-cells = <1>;
+ reg = <2>;
+ status = "okay";
+ phy-supply = <&vbus_p2>;
+ };
+ };
+
+Example of node using the phy:
+
+ /* This nodes declares all three ports as host */
+
+ ehci0: usb@0x18048000 {
+ compatible = "generic-ehci";
+ reg = <0x18048000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usbphy0_0 1 &usbphy0_1 1 &usbphy0_2 1>;
+ status = "okay";
+ };
+
+ /*
+ * This node declares port 2 phy
+ * and configures it for device
+ */
+
+ usbd_udc_dwc1: usbd_udc_dwc@0x1804c000 {
+ compatible = "iproc-udc";
+ reg = <0x1804c000 0x2000>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usbphy0_2 0>;
+ phy-names = "usb";
+ };
--
2.3.4


\
 
 \ /
  Last update: 2015-04-01 23:21    [W:0.145 / U:0.564 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site