lkml.org 
[lkml]   [2015]   [Apr]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V3 1/1] serial: 8250_pci: port failed after wakeup from S3
Date
Serial ports of F81504/F81508/F81512 will failed when wakeup from S3(STR).

It's due to when the system wakeup from S3(STR), this PCI device's
configuration space from 0x40 to 0x40 + max_port * 0x08 should be
re-configured.

We move all initialization from pci_fintek_setup() to pci_fintek_init() and
set it to pci_serial_quirks .init section. It's will re-init this device when
system wakeup from pciserial_resume_ports().

Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
---
drivers/tty/serial/8250/8250_pci.c | 114 ++++++++++++++++---------------------
1 file changed, 50 insertions(+), 64 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 98e5a6d..08da4d3 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1690,88 +1690,71 @@ static int pci_fintek_setup(struct serial_private *priv,
struct uart_8250_port *port, int idx)
{
struct pci_dev *pdev = priv->dev;
- unsigned long iobase;
u8 config_base;
+ u16 iobase;
+
+ config_base = 0x40 + 0x08 * idx;
+
+ /* Get the io address from configuration space */
+ pci_read_config_word(pdev, config_base + 4, &iobase);
+
+ dev_dbg(&pdev->dev, "%s: idx=%d iobase=0x%x", __func__, idx, iobase);
+
+ port->port.iotype = UPIO_PORT;
+ port->port.iobase = iobase;
+
+ return 0;
+}
+
+static int pci_fintek_init(struct pci_dev *dev)
+{
+ unsigned long iobase;
+ u32 max_port, i;
u32 bar_data[3];
+ u8 config_base;

- /*
- * Find each UARTs offset in PCI configuraion space
- */
- switch (idx) {
- case 0:
- config_base = 0x40;
+ switch (dev->device) {
+ case 0x1104: /* 4 ports */
+ case 0x1108: /* 8 ports */
+ max_port = dev->device & 0xff;
break;
- case 1:
- config_base = 0x48;
- break;
- case 2:
- config_base = 0x50;
- break;
- case 3:
- config_base = 0x58;
- break;
- case 4:
- config_base = 0x60;
- break;
- case 5:
- config_base = 0x68;
- break;
- case 6:
- config_base = 0x70;
- break;
- case 7:
- config_base = 0x78;
- break;
- case 8:
- config_base = 0x80;
- break;
- case 9:
- config_base = 0x88;
- break;
- case 10:
- config_base = 0x90;
- break;
- case 11:
- config_base = 0x98;
+ case 0x1112: /* 12 ports */
+ max_port = 12;
break;
default:
- /* Unknown number of ports, get out of here */
return -EINVAL;
}

/* Get the io address dispatch from the BIOS */
- pci_read_config_dword(pdev, 0x24, &bar_data[0]);
- pci_read_config_dword(pdev, 0x20, &bar_data[1]);
- pci_read_config_dword(pdev, 0x1c, &bar_data[2]);
-
- /* Calculate Real IO Port */
- iobase = (bar_data[idx/4] & 0xffffffe0) + (idx % 4) * 8;
+ pci_read_config_dword(dev, 0x24, &bar_data[0]);
+ pci_read_config_dword(dev, 0x20, &bar_data[1]);
+ pci_read_config_dword(dev, 0x1c, &bar_data[2]);

- dev_dbg(&pdev->dev, "%s: idx=%d iobase=0x%lx config_base=0x%2x\n",
- __func__, idx, iobase, config_base);
+ for (i = 0; i < max_port; ++i) {
+ /* UART0 configuration offset start from 0x40 */
+ config_base = 0x40 + 0x08 * i;

- /* Enable UART I/O port */
- pci_write_config_byte(pdev, config_base + 0x00, 0x01);
+ /* Calculate Real IO Port */
+ iobase = (bar_data[i / 4] & 0xffffffe0) + (i % 4) * 8;

- /* Select 128-byte FIFO and 8x FIFO threshold */
- pci_write_config_byte(pdev, config_base + 0x01, 0x33);
+ /* Enable UART I/O port */
+ pci_write_config_byte(dev, config_base + 0x00, 0x01);

- /* LSB UART */
- pci_write_config_byte(pdev, config_base + 0x04, (u8)(iobase & 0xff));
+ /* Select 128-byte FIFO and 8x FIFO threshold */
+ pci_write_config_byte(dev, config_base + 0x01, 0x33);

- /* MSB UART */
- pci_write_config_byte(pdev, config_base + 0x05, (u8)((iobase & 0xff00) >> 8));
+ /* LSB UART */
+ pci_write_config_byte(dev, config_base + 0x04,
+ (u8)(iobase & 0xff));

- /* irq number, this usually fails, but the spec says to do it anyway. */
- pci_write_config_byte(pdev, config_base + 0x06, pdev->irq);
+ /* MSB UART */
+ pci_write_config_byte(dev, config_base + 0x05,
+ (u8)((iobase & 0xff00) >> 8));

- port->port.iotype = UPIO_PORT;
- port->port.iobase = iobase;
- port->port.mapbase = 0;
- port->port.membase = NULL;
- port->port.regshift = 0;
+ pci_write_config_byte(dev, config_base + 0x06, dev->irq);
+ }

- return 0;
+ return max_port;
}

static int skip_tx_en_setup(struct serial_private *priv,
@@ -2814,6 +2797,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_fintek_setup,
+ .init = pci_fintek_init,
},
{
.vendor = 0x1c29,
@@ -2821,6 +2805,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_fintek_setup,
+ .init = pci_fintek_init,
},
{
.vendor = 0x1c29,
@@ -2828,6 +2813,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_fintek_setup,
+ .init = pci_fintek_init,
},

/*
--
1.9.1


\
 
 \ /
  Last update: 2015-04-01 08:41    [W:0.058 / U:0.920 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site