lkml.org 
[lkml]   [2015]   [Apr]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 4/4] Documentation: extcon: usb-gpio: update usb-gpio binding description
On 01/04/15 10:23, Robert Baldyga wrote:
> Add information about VBUS pin detection support, 'debounce' property
> and some other details.
>
> Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>

Acked-by: Roger Quadros <rogerq@ti.com>

cheers,
-roger

> ---
> .../devicetree/bindings/extcon/extcon-usb-gpio.txt | 28 ++++++++++++++++++++--
> 1 file changed, 26 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
> index af0b903..7096f39 100644
> --- a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
> +++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
> @@ -1,16 +1,40 @@
> USB GPIO Extcon device
>
> -This is a virtual device used to generate USB cable states from the USB ID pin
> -connected to a GPIO pin.
> +This is a virtual device used to generate USB cable states from the USB
> +ID and VBUS signals connected to GPIO pins.
> +
> +The extcon cable states USB and USB_HOST are actually VBUS and !ID
> +pin states and do not indicate what mode the USB needs to operate in.
> +That decision is done by the USB stack.
> +
> +Some devices have only one of these GPIO pins, so we support cases when
> +only one of them is present. Hence properties 'id-gpio' and 'vbus-gpio'
> +are described as optional, but at least one of them has to be present
> +in extcon-usb-gpio node.
> +
> +In general we have three cases:
> +1. If VBUS and ID gpios are present we pass them as is
> + USB-HOST = !ID, USB = VBUS
> +2. If only VBUS gpio is present we assume that ID pin is always High.
> + USB-HOST = false, USB = VBUS.
> +3. If only ID pin is available we infer the VBUS pin states based on ID.
> + USB-HOST = !ID, USB = ID
>
> Required properties:
> - compatible: Should be "linux,extcon-usb-gpio"
> +
> +Optional properties
> - id-gpio: gpio for USB ID pin. See gpio binding.
> +- vbus-gpio: gpio for USB VBUS pin. See gpio binding.
> +- debounce: gpio debounce time in milliseconds (u32).
> +
>
> Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below:
> extcon_usb1 {
> compatible = "linux,extcon-usb-gpio";
> id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
> + vbus-gpio = <&gpio6 2 GPIO_ACTIVE_HIGH>;
> + debounce = <25>;
> }
>
> &omap_dwc3_1 {
>



\
 
 \ /
  Last update: 2015-04-01 14:01    [W:0.100 / U:0.432 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site